Français dropdown-ico

Manuel d’utilisation hussman ESSS-0303

24 pages 0.79 mb
Télécharger

Aller à la page of 24

Summary
  • hussman ESSS-0303 - page 1

    /Chino ESSS / ESS Self Ser vice Match ESC / ESCS Re v .0303 Installation & Operation Manual ESSS / ESS Self Ser vice Cases (Match ESC / ESCS) p/n IGSS-ESSS / ESS-0303 INST ALLA TION & O PE RA T IO N GUIDE ...

  • hussman ESSS-0303 - page 2

    IGSS-ESS/ESSS-0303 2 /Chino A publication of Hussmann ® Chino 13770 Ramona A v enue • Chino , California 91710 (909) 628-8942 F AX (909) 590-4910 (800) 395-9229 K eep this booklet with the case at all times f or futur e refer ence . THIS BOOKLET CONT AINS INFORMA TION ON: ESSS: Refrigerated Self Service cases Matc hes Multidec k Ser- vice Cases ...

  • hussman ESSS-0303 - page 3

    Rev.0 303 3 Cut & Plan Vie ws ESSS 8" CASE FRONT 8" DRAIN AND ELECTRICAL MECHANICAL STUB UP AREA 18" X 18" REFRIG. MECHANICAL STUB UP AREA 18" X 18" ESS (ESSS) Plan View Scale = 1/4" 8'-2" (V ARIABLE LENGTHS) 1" 1" 43 5 / 8 " (49 1 / 4 " / 46 3 / 4 ") ESS Self-Service Scale = ...

  • hussman ESSS-0303 - page 4

    IGSS-ESS/ESSS-0303 4 LOCA TION The refrigerated mer chandisers hav e been designed for use only in air conditioned stor es where temperatur e and humidity ar e maintained at or below 75°F and 55% rela- tive humidity . DO NO T allow air conditioning, electric fans, ov ens, open doors or windows (etc .) to cr eate air cur - r ents ar ound the mercha ...

  • hussman ESSS-0303 - page 5

    Rev.0 303 5 Do not use cam locks to pull cases together. 2. Secur e joint backer . Located behind cart bumper supor t at joints. T o adjust scr ews holding bumper cart to case on either side or the joint and slide extrusion to center of joint. This piece suppor ts the forn t panel at the joint. 3. Apply bead of silicone to top of bulkheads. 4. Slip ...

  • hussman ESSS-0303 - page 6

    IGSS-ESS/ESSS-0303 6 Plumbing WASTE OUTLET AND P-TRAP The waste outlet is located off the center of the case on one side allowing drip piping to be run lengthwise under the fixture. A 1-1/2" P-trap and thr eaded adapter ar e supplied with each fixture. The P-trap must be installed to pr ev ent air leakage and insect entrance into the fixtur e ...

  • hussman ESSS-0303 - page 7

    Rev.0 303 7 Refrigeration REFRIGERANT TYPE The standard r efrigerant will be R-22 unless otherwise specified on the customer or der . Check the serial plate on the case for inf ormation. PIPING The refrigerant line outlets ar e located under the case . Locate first the electrical box, the outlets are then on the same side of the case but at the opp ...

  • hussman ESSS-0303 - page 8

    IGSS-ESS/ESSS-0303 8 Electrical WIRING COLOR CODE GREEN GROUND PURPLE ANTI-SWEA T ORANGE LIGHTS YELLO W RECEPT ACLE RED / BLACK T -ST A T /SOLENOID 230V BLACK / WHITE T - S TAT / S O L E N O I D 115V BRO WN F AN MO T ORS CASE MUST BE GROUNDED NOTE: Refer to label affixed to case to determine the actual configuration as checked in the “TYPE INSTAL ...

  • hussman ESSS-0303 - page 9

    Rev.0 303 9 User Information Joi n t Tr i m ESSS Only (ESS dows not ha ve joint trim) CAMLOCK & SEALANT LOCA TIONS CAMLO CK AC CESS PA N E L APPL Y SEALANT TO S H ADED AREA JOINT BACKER LOCA TION CAMLOCK L OCA TI ON S SEAL AROUND PIPING ACCESS HOLES BOL T INSIDE WEDGES CAMLOCK L OCA TI ON STOCKING Improper temperatur e and lighting will cause s ...

  • hussman ESSS-0303 - page 10

    IGSS-ESS/ESSS-0303 10 deh ydration pr ocess. The only other moistur e within the case is that in the pr oduct itself. A single lev el of meat will dr y out faster than a fully loaded case of 3–4 lev els of meat. IMPOR T ANT STEPS 1. Do not set temperatur e too cold, as this causes pr oduct deh ydration. Product T emperature: 33°–35°! Set ther ...

  • hussman ESSS-0303 - page 11

    Rev.0 303 11 attracts dust and dirt to the surface . Blotting with a clean damp cloth is recommended to r emove charge. ANTIST A TIC CO A TINGS F or acrylic used indoors, antistatic coatings successfully pre v ent the accumulation of an electr ostatic charge for periods of sev eral months—if the surface is not washed or wiped down with a w et clo ...

  • hussman ESSS-0303 - page 12

    IGSS-ESS/ESSS-0303 12 Maintenance ELECTRICAL PRECAUTIONS BEFORE SERVICING – Always disconnect electrical power at the main disconnect when servicing or replacing any electrical component This includes (but not limited to) Fans, Heaters, Thermostats, and Lights. REPLACING FLUORESCENT LAMPS Fluorescent lamps ar e furnished with moisture r esistant ...

  • hussman ESSS-0303 - page 13

    Rev.0 303 13 Specifications NOTES: These refrigerated merchandisers have been designed for use in stores where temperatures and humidity are maintained at or below 75°F and 55%RH. Stores are responsible for setting their cases approprately in conditions which vary from the above. The number of defrosts and/or the duration may vary for cases displa ...

  • hussman ESSS-0303 - page 14

    IGSS-ESS/ESSS-0303 14 Electrical Schematics Light Switch Overhead Canopy Lights Ledge Light (Optional) Ballats WH3-120-164 (125-04-0118) Thermostat Suction Solenoid Duplex Receptacles GFCI Dedicated Line Evaporator Fan Cap Case to Case Harness Single case Pigtail F17T8-SPX30 (2) 125-04-0101 125-04-0110 125-04-0111 125-04-0113 125-04- 0113 125-04- 0 ...

  • hussman ESSS-0303 - page 15

    Rev.0 303 15 Light Switch Front Lights (optional) Ledge Lights (optional) Ballast WH3-120-164 (125-04-0118) Thermostat Liquid Solenoid Duplex Receptacles GFCI Dedicated Line Ballast Extension Box (Switched Power) Evaporator Fans Cap Case to Case Harness Single case Pigtail F32T8-SPX30 (2) 125-04-0103 125-04-0101 125-04-0108 125-04-0110 125-04-0111 ...

  • hussman ESSS-0303 - page 16

    IGSS-ESS/ESSS-0303 16 Light Switch Front Lights Ledge Lights (Optional) Ballast WH3-120-164 (125-04-0118) Thermostat Liquid Solenoid Duplex Receptacles GFCI Dedicated Line Ballast Extension Box (Switched Power) Evaporator Fans Cap Case to Case Harness Single case Pigtail F25T8-SPX30 (2) Plenum extension Evaporator Fans 125-04-0104 125-04-0101 125-0 ...

  • hussman ESSS-0303 - page 17

    Rev.0 303 17 Light Switch Front Lights Ledge Lights (Optional) Ballast WH3-120-164 (125-04-0118) Thermostat Liquid Solenoid Duplex Receptacles GFCI Dedicated Line Ballast Extension Box (Switched Power) Evaporator Fans Cap Case to Case Harness Single case Pigtail F32T8-SPX30 (2) Plenum extension Evaporator Fans 125-04-0105 125-04-0101 125-04-0108 12 ...

  • hussman ESSS-0303 - page 18

    IGSS-ESS/ESSS-0303 18 Light Switch Front Lights Ledge Lights (Optional) Ballasts WH3-120-164 (125-04-0118) Thermostat Liquid Solenoid F32T8-SPX30 (1) Duplex Receptacles GFCI Dedicated Line Ballast Extension Box (Switched Power) Evaporator Fans Cap Case to Case Harness Single case Pigtail F25T8-SPX30 (2) Plenum extension Evaporator Fans Plenum exten ...

  • hussman ESSS-0303 - page 19

    Rev.0 303 19 Light Switch Front Lights Ledge Lights (Optional) Ballasts WH3-120-164 (125-04-0118) Thermostat Liquid Solenoid F32T8-SPX30 (1) Duplex Receptacles GFCI Dedicated Line Ballast Extension Box (Switched Power) Evaporator Fans Cap Case to Case Harness Single case Pigtail F32T8-SPX30 (2) Plenum extension Evaporator Fans Plenum extension Evap ...

  • hussman ESSS-0303 - page 20

    IGSS-ESS/ESSS-0303 20 APPENDIX A. – Temperature Guidlines The refrigerators should be operated according to the manufacturer’s published engineering specifications for entering air temperatures for specific equipment applications. Table 1 shows the typical temperature of the air entering the food zone one hour before the start of defrost and on ...

  • hussman ESSS-0303 - page 21

    Rev.0 303 21 only in Fahrenheit shall be accurate to 2°F. The thermometer should be checked for proper calibration. (It should read 32°F when the stem is immersed in an ice water bath). b) LOCATION – The probe or sensing element of the thermometer should be located in the airstream where the air first enters the display or storage area, and not ...

  • hussman ESSS-0303 - page 22

    IGSS-ESS/ESSS-0303 22 ...

  • hussman ESSS-0303 - page 23

    Rev.0 303 23 Limited W arranty This warranty is made to the original user at the original installation site and is not transf erable . Hussmann merchandisers ar e war ranted to be free fr om def ect in material and workmanship under normal use and ser vice for a period of one (1) y ear fr om the date of original installation (not to exceed fifteen ...

  • hussman ESSS-0303 - page 24

    IGSS-ESS/ESSS-0303 24 The MODEL NAME and SERIAL NUMBER is required in or der to pr ovide you with the correct parts and information for y our particular unit. They can be found on a small metal plate on the unit. Please note them below for futur e refer ence . MODEL: SERIAL NUMBER: /Chino Additional copies of this publication may be obtained b y co ...

Fabricant hussman Catégorie Refrigerator

Les documents que nous recevons du fabricant de l'appareilhussman ESSS-0303 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques hussman
- manuels d’utilisations ESSS-0303
- fiches produit hussman
- dépliants
- ou étiquettes-énergie hussman ESSS-0303
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation hussman ESSS-0303.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation hussman ESSS-0303, manuels d’entretien, brefs manuels ou manuels de l’utilisateur hussman ESSS-0303. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit hussman ESSS-0303.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil hussman ESSS-0303, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser hussman ESSS-0303 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs hussman ESSS-0303.

Le manuel d’utilisation complet hussman, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel hussman ESSS-0303 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières hussman ESSS-0303, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lhussman ESSS-0303 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil hussman ESSS-0303 - qui devraient nous aider dans les premières étapes lors de l'utilisation hussman ESSS-0303
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de hussman ESSS-0303
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service hussman ESSS-0303 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de hussman ESSS-0303?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec hussman ESSS-0303, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec hussman ESSS-0303 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)