-
TP-Link TD-W8900G - page 1
Rev ： 1.0. 1 ...
-
TP-Link TD-W8900G - page 2
I COPYRIGHT & TRADEMARKS Specifications are subjec t to change without notice. is a registered trademark of TP-LINK Technologies Co., Ltd. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specificat ions may be reproduced in any form or b y any means or used to make any derivativ ...
-
TP-Link TD-W8900G - page 3
TD-W8900G 54M Wireless ADSL2+ Router User Guide II FCC ST A TEMENT This equipment has been tested and found to comply wi th the limits for a Class B digital device, pursuant to part 15 of the FCC Ru les. These limits are designed to pr ovide reasonable protectio n against harmful interference in a residential installation. This equipment ge nerates ...
-
TP-Link TD-W8900G - page 4
TD-W8900G 54M Wireless ADSL2+ Router User Guide III National Restrictions 2400.0-2483.5 MHz Country Restriction Reason/remark Bulgaria General authorization r equire d for outdoor use and public service France Outdoor use limited to 10 mW e.i.r.p. w ithin the b and 2454-2483.5 MHz Military Radiol ocation use. Refarming of the 2.4 GHz band has been ...
-
TP-Link TD-W8900G - page 5
TD-W8900G 54M Wireless ADSL2+ Router User Guide IV Package contents The following contents should be found in your box: ¾ One TD-W8900G 54M Wireless ADSL2+ Router ¾ One DC power Adapter for TD-W8900G 54M Wireless ADSL2+ Router ¾ Quick Installation Guide ¾ One RJ45 cable ¾ Two RJ11 cables ¾ One ADSL splitter ¾ One Resource CD for TD-W8900G 54 ...
-
TP-Link TD-W8900G - page 6
TD-W8900G 54M Wireless ADSL2+ Router User Guide V CONTENTS Chapter 1. About This U ser Guide .......................................................................... 1 1.1 Purpose ..................................................................................................................... 1 1.2 Conventions ................................ ...
-
TP-Link TD-W8900G - page 7
TD-W8900G 54M Wireless ADSL2+ Router User Guide VI 5.5 Wireless LAN Configuration .................................................................................... 55 5.5.1 Wireless – Basic ............................................................................................................. 55 5.5.2 Wireless – Security .............. ...
-
TP-Link TD-W8900G - page 8
1 Chapter 1. About This User Guide 1.1 Purpose For helping user know about TD-W8900G 54M Wirele ss ADSL2+ Router better , use it accurately and adequately , maintain it expediently , we write this User Guide. This Guide introduces the product comprehensively , including the prod uct’s f unctions, p arameters and specifications. It also explains h ...
-
TP-Link TD-W8900G - page 9
TD-W8900G 54M Wireless ADSL2+ Router User Guide 2 Chapter 2. Product Overview 2.1 Overview of the Router Thank you for choosing the TD-W8900G 54M Wirel ess ADSL2+ Router . The Router is designed to provide a simple and cost-effective ADSL Internet connection for a private Ethernet or 802.11g/802.11b wireless network. The Router is easy to use. The ...
-
TP-Link TD-W8900G - page 10
TD-W8900G 54M Wireless ADSL2+ Router User Guide 3 ¾ AFE to support Annex A/ B/C/I/J/K, Land M deployments. ¾ Provides external splitter . ¾ Adopts Advanced DMT modulati on and demodulation technology . ¾ Supports bridge mode and Router function. ¾ Multi-user sharing a high-speed Internet connection ¾ Conn ecting the internet on demand and dis ...
-
TP-Link TD-W8900G - page 11
TD-W8900G 54M Wireless ADSL2+ Router User Guide 4 2.4 T ransmit Dat a-rate ¾ Maximum Download S peed : 24Mbps （ ADSL2+), 8Mbps （ ADSL). ¾ Maximum Upload S peed : 1Mbps. ¾ Supports 54/48/36/24/18/ 12/9/6Mbps (IEEE 802.1 1g) and 1 1/5.5/2/1Mbps (IEEE 802.1 1b) WLAN data transfer rates. ...
-
TP-Link TD-W8900G - page 12
TD-W8900G 54M Wireless ADSL2+ Router User Guide 5 Chapter 3. Hardware Installation Guide 3.1 The Front Panel The Router’s LEDs are located on the front panel. Figure 3-1 The LED indicators on the front panel include the Power , Sys tem , ADSL , WLAN and 1-4 (LAN) . The ADSL, WLAN and 1-4 (LAN) indicators m onitor link status and activity (Link/Ac ...
-
TP-Link TD-W8900G - page 13
TD-W8900G 54M Wireless ADSL2+ Router User Guide 6 3.3 The Back Panel The Router's ports, where the cables are connected, and RESET button are located on the back panel. Figure 3-2 ¾ Line: Connect to the Modem Port of Splitter or to the telephone line. ¾ Reset Button: There are two wa ys to reset the Router 's factory defaults. Press the ...
-
TP-Link TD-W8900G - page 14
TD-W8900G 54M Wireless ADSL2+ Router User Guide 7 connection. ¾ The Router can be placed on a shelf or desktop. ¾ Operating temperature : 0 ℃ ~40 ℃ (32 ℉ ~104 ℉ ). ¾ Operating Humidity : 10% ~ 90% RH Non-congealing. 3.6 Connecting the Router Before installing the Router, please make sure y our broadband service provided by yo ur ISP is a ...
-
TP-Link TD-W8900G - page 15
TD-W8900G 54M Wireless ADSL2+ Router User Guide 8 connection represents the WAN interface, the connection to the Internet. It is the physical link to the service provider’s network back bone and ultimately to the Internet. 3.6.2.2. Hub or Switch to Router Connection Connect the Router to an uplink port (MDI-II) on an Ethernet hub or switch with a ...
-
TP-Link TD-W8900G - page 16
TD-W8900G 54M Wireless ADSL2+ Router User Guide 9 Figure 4-1 ) Note: Do not mix up the user name and password with your ADSL account user name and password which needed for PPP connections. 2. The default screen shows as below. Change the VPI or VCI values which are used to define a unique path for your c onnection. If you have been given speci fic ...
-
TP-Link TD-W8900G - page 17
TD-W8900G 54M Wireless ADSL2+ Router User Guide 10 3. On the Connection Type screen, you can select a connec tion type (PPPoA, PPPoE, MER, IPoA or Bridging), which is provided by your ISP. We select PPPoE mode (For example), and then click “Next “to continue. Figure 4-3 4. Enter the PPP Username and PPP Pass word provided by your I SP. If PPPoE ...
-
TP-Link TD-W8900G - page 18
TD-W8900G 54M Wireless ADSL2+ Router User Guide 11 Figure 4-4 5. Use the default setting of this screen click “Next” to continue. Figure 4-5 6. Use the default IP Address 192.168.1.1 and Subnet Mask 255.255.255.0. Us e the default setting of “ Enable DHCP Server ”, and click “Next” to continue. ...
-
TP-Link TD-W8900G - page 19
TD-W8900G 54M Wireless ADSL2+ Router User Guide 12 Figure 4-6 7. Use the default setting “ Enable Wireless ”. Default SSID is “TP-LI NK”, then click “Next”. Figure 4-7 8. You will see the WAN Setup-Summary screen below, click " Save/Reboot " to save these settings and reboot the Router. ...
-
TP-Link TD-W8900G - page 20
TD-W8900G 54M Wireless ADSL2+ Router User Guide 13 Figure 4-8 ) Note: The reboot process will take a wh ile to complete, please wait befo re reopening your web browser. 4.2 Configure PC Your PC needs a network adapter. You may directly connect your adapter to the Router, or you may connect your adapter to a Hub/Switch, and then connect the Hub/Swit ...
-
TP-Link TD-W8900G - page 21
TD-W8900G 54M Wireless ADSL2+ Router User Guide 14 Figure 4-9 2. In the Network Connections window, right-click on LAN (Local Area Conn ection), then click Properties. Figure 4-10 3. In the General tab of Internet Protocol (TCP/IP) Properties menu, highlight Internet Protocol (TCP/IP) under “This c onnection uses the following item s:” by click ...
-
TP-Link TD-W8900G - page 22
TD-W8900G 54M Wireless ADSL2+ Router User Guide 15 Click on the Properties button. Figure 4-11 4. Select “Obtain an IP address automatically ” by clicking the radio-button. Click OK Figure 4-12 ¾ Configure the IP address manually Open TCP/IP Properties of the LAN card in your PC, enter the IP address as 192.168.1.* (* is any value between 2 to ...
-
TP-Link TD-W8900G - page 23
TD-W8900G 54M Wireless ADSL2+ Router User Guide 16 ¾ Now, you can run the Ping command in t he command prompt to ve rify the network connection between your PC and the Router. The following example is in Windows XP Operating System. Open a command prompt, From the Start menu on your desktop, select run tab, type cmd in the field, and type ping 192 ...
-
TP-Link TD-W8900G - page 24
TD-W8900G 54M Wireless ADSL2+ Router User Guide 17 ) Note: a) The 1/2/3/4 LEDs of LAN port which you link to on the Router and LEDs on your PC's adapter should be lit. b) If the TCP/IP configurati on for your PC is correct? ) Note: If the Router's IP address is 192. 168.1.1, your PC's IP address must be within the range of 192.168.1. ...
-
TP-Link TD-W8900G - page 25
TD-W8900G 54M Wireless ADSL2+ Router User Guide 18 Figure 5-1 There are six main menus shown on the screen, they are Device Info , Quick Setup , Advanced Setup , Wireless , Diagnostics and Management . Additional menus will be available after you click one of the main menus. Click one of the ma in menus, and you will be able to configure the corres ...
-
TP-Link TD-W8900G - page 26
TD-W8900G 54M Wireless ADSL2+ Router User Guide 19 Figure 5-2 ) Note: Click the other submenus under the main menu Device Info , you will be able to view the corresponding information about WAN , Statistics , Route , ARP and DHCP . 5.3 Quick Setup Please refer to the Chapter 4 to get the detailed information. 5.4 Advanced Setup Choose “ Advanced ...
-
TP-Link TD-W8900G - page 27
TD-W8900G 54M Wireless ADSL2+ Router User Guide 20 Figure 5-3 ¾ W AN Port Information T able: This table describes the W AN port settings and the relevant manipulation to each interface. ¾ Remove: Select the check box in the table (shown in Figure 5-3) and then click the Remove tab, the corresponding interfac e will be deleted in the table. ¾ Ad ...
-
TP-Link TD-W8900G - page 28
TD-W8900G 54M Wireless ADSL2+ Router User Guide 21 Figure 5-4 1. Follow the instructions below to configure the A TM PVC on the screen (shown in Figure 5-4). Make sure you have the necessary in formation before you configure it. 1) Enter the VPI and VCI values provided by your ISP, they should not be changed unless you have been instructed to chang ...
-
TP-Link TD-W8900G - page 29
TD-W8900G 54M Wireless ADSL2+ Router User Guide 22 service, the Quality of Serv ice menu will be added to the W eb-based Utility, the detailed configuration will be described in 5.4.5 Quality of Service . 2. Select the Connection T ype in the next screen (shown in Figure 5-5). Figure 5-5 1) Select the Connection Type and Encapsulation Mode your ISP ...
-
TP-Link TD-W8900G - page 30
TD-W8900G 54M Wireless ADSL2+ Router User Guide 23 1. PPPoA If you choose connection type PPPoA on the screen above (shown in Figure 5-5), you will see the screen belo w (shown in Figure 5-6). Follow the instru ctions to configure the WAN Interface. Figure 5-6 1) Enter the PPP Username and PPP Password provided by you r ISP exactly, select the Auth ...
-
TP-Link TD-W8900G - page 31
TD-W8900G 54M Wireless ADSL2+ Router User Guide 24 Figure 5-7 5) Enable the IGMP Multicast and WAN Service on the screen above, if you are not sure about the IGMP, just leave the default setting. Note that if you want to adopt the PPPoA service, you have to select the Enable WAN Service option in the screen above, or else the service will not take ...
-
TP-Link TD-W8900G - page 32
TD-W8900G 54M Wireless ADSL2+ Router User Guide 25 The information is same as the information in Figure 5-3. 2. PPPoE If you choose PPPoE in the previous screen (shown in Figure 5-5), the configuration is similar to PPPoA , the only difference is that you should set the PPPoE Service Name on the corresponding screen. You can refer to Chapter 4 to a ...
-
TP-Link TD-W8900G - page 33
TD-W8900G 54M Wireless ADSL2+ Router User Guide 26 the following IP Address , and then enter the WAN IP Address and WAN Subnet Mask . 2) Configure the default gateway . If you are provided a dynamic gateway address, please select obtain default gateway automatically , and then the Router will automatically get gateway parameters from your ISP. If y ...
-
TP-Link TD-W8900G - page 34
TD-W8900G 54M Wireless ADSL2+ Router User Guide 27 the screen above, or else the service will not take effect. ¾ service name: You can enter the service name in the text box o r leave the default name. ) Note: If you select the NAT and Security check box on the screen (shown in Figure 5-10), the NAT and Securit y menu will be added to the Web- bas ...
-
TP-Link TD-W8900G - page 35
TD-W8900G 54M Wireless ADSL2+ Router User Guide 28 Figure 5-12 1) If you want to adopt the Bridge service, you have to select the Enable Bridge Service option in the screen above, or else the service will not take effect. 2) Enter the service name in this screen, otherwise leave the default setting. 3) Click the Next button, and you will s ee the n ...
-
TP-Link TD-W8900G - page 36
TD-W8900G 54M Wireless ADSL2+ Router User Guide 29 5.4.2 LAN Choose “ Advanced Setup ” Æ “ LAN ”, and you will see the LAN screen (shown in Figure 5-14 ) ， the section allows you to configure the Router’s LAN ports settings. Figure 5-14 ¾ IP Address: Y ou can configure the Router ’s IP Ad dress and Subnet Mask for LAN Interface. ...
-
TP-Link TD-W8900G - page 37
TD-W8900G 54M Wireless ADSL2+ Router User Guide 30 ¾ DHCP Server: These settings allow you to confi gure the Router‘s Dynamic Host Configuration Protocol (DHCP) server function. The DHCP serv er is enabled by default for the Router ’s Ethernet LAN interf ace. DHCP service will supply IP settings to computers which are configured to automatical ...
-
TP-Link TD-W8900G - page 38
TD-W8900G 54M Wireless ADSL2+ Router User Guide 31 3. Type the MAC Address(00:13:8F:A9:E6:CA for in stance) of the computer which you want to reserve an IP(192.168.1.100 for instance) for in the MAC Address text box; 4. Type the IP Address(192.168.1.100 for instance) you have reserve d in the Reserved IP Address text box; 5. Click save botton to sa ...
-
TP-Link TD-W8900G - page 39
TD-W8900G 54M Wireless ADSL2+ Router User Guide 32 Figure 5-15 Choose “ Advanced Setup ” Æ “ NAT ”, there are four submenus under the main men u : Virtual Servers , Port Triggering , DMZ Host and ALG . Click any of them, and you will be able to configure the corre sponding function. 5.4.3.1. Virtual Servers Choose “ Ad vanced Set up ” ...
-
TP-Link TD-W8900G - page 40
TD-W8900G 54M Wireless ADSL2+ Router User Guide 33 ¾ Virtual Server T able: The table indicates the informati on about the Virtual Server entries. Server Name: This is the name of the Virtual Server . It is ex clusive and must be filled in. External Port St art: The base number of External Ports. Y ou can type a service port or leave it bl ...
-
TP-Link TD-W8900G - page 41
TD-W8900G 54M Wireless ADSL2+ Router User Guide 34 Figure 5-17 2. Select the service which you want to use from the drop-down lis t. If the list does not have the service you need, type the name of the custom service in the text box. 3. Type the IP Address of the computer in the Server IP Address text box. 4. Enter the External Port Start, External ...
-
TP-Link TD-W8900G - page 42
TD-W8900G 54M Wireless ADSL2+ Router User Guide 35 only need to enter the Server IP Address for the Virtual Server. 5.4.3.2. Port Triggering Choose “ Advanced Set up ” Æ “ NAT ” Æ “ Port Triggering ”, you can set Port Triggering on the screen (shown in Figure 5-18). Some applications require that specific ports in the Router's fi ...
-
TP-Link TD-W8900G - page 43
TD-W8900G 54M Wireless ADSL2+ Router User Guide 36 1. Click the Add button (pop-up Figure 5-18), and then you will se t the new Port Triggering in the next screen (shown in Figure 5-19). Figure 5-19 2. Select the application from the drop-down list. If the list does not have the application that you want, select the Custom application radio-button, ...
-
TP-Link TD-W8900G - page 44
TD-W8900G 54M Wireless ADSL2+ Router User Guide 37 Figure 5-20 To add a new DMZ Host : You can enter the computer 's IP address and then click Save/Apply to activate the DMZ host you set on this page. ) Note: DMZ host forwards all the ports at the same ti me. Any PC whose port is being forwarded must have its DHCP client function di sabled and ...
-
TP-Link TD-W8900G - page 45
TD-W8900G 54M Wireless ADSL2+ Router User Guide 38 Figure 5-22 5.4.4.1. IP Filtering The IP address filtering feature makes it possible fo r administrators to contro l user's access to the Internet, which is based on user's IP . The IP address filtering includes Outgoing and Incoming , the detailed descriptions are provided below. IP Filt ...
-
TP-Link TD-W8900G - page 46
TD-W8900G 54M Wireless ADSL2+ Router User Guide 39 Figure 5-24 2. Enter the Filter name for the rule, it is excl usive and must be filled. 3. Select the protocol: TCP/UDP , TCP , UDP or ICMP in the drop-down list for the connection between the Source IP address and Destination IP address. 4. Enter a Source IP Address in dotted-decimal notati on for ...
-
TP-Link TD-W8900G - page 47
TD-W8900G 54M Wireless ADSL2+ Router User Guide 40 Figure 5-25 Setup an Incoming IP Filtering rule: 1. Click the Add button (pop-up Figure 5-25), and t hen you will set the new rule in the next screen (shown in Figure 5-26). Figure 5-26 2. Enter the Filter name for the rule, it is excl usive and must be filled in. 3. Select Protocol in the drop- do ...
-
TP-Link TD-W8900G - page 48
TD-W8900G 54M Wireless ADSL2+ Router User Guide 41 ) Note: When you add a Incoming IP Filtering entry, you must configure at leas t one condition on the screen above except the Filter name. If you leave Protocol blank, it means that the rule is effective to all protocols, if you leave the Sour ce IP address and/or Destination IP address blank, it s ...
-
TP-Link TD-W8900G - page 49
TD-W8900G 54M Wireless ADSL2+ Router User Guide 42 1. Click the Add button (pop-up Figure 5-27), then you will set th e new rule in the next screen (shown in Figure 5-28). Figure 5-28 2. Select Protocol Type in the drop-down list for the rule. 3. Enter Destination MAC Address and Source MAC Address in the text box. 4. Select Frame Direction in the ...
-
TP-Link TD-W8900G - page 50
TD-W8900G 54M Wireless ADSL2+ Router User Guide 43 Figure 5-29 To setup a Parental Control rule: 1. Click the Add button (pop-up Figure 5-29), and t hen you will set the new rule in the next screen (shown in Figure 5-30). Figure 5-30 2. Enter the User Name of the LAN device c onnected to the Router. 3. To restrict the device where t he browser is r ...
-
TP-Link TD-W8900G - page 51
TD-W8900G 54M Wireless ADSL2+ Router User Guide 44 Figure 5-31 Click the Add button, and you can configure t he QoS on the next screen (shown in Figure 5-32). ...
-
TP-Link TD-W8900G - page 52
TD-W8900G 54M Wireless ADSL2+ Router User Guide 45 Figure 5-32 After you specify the condition, click the Save/Apply button to save the entry. ) Note: A rule must be consisting of a class name and at least one condition abo ve. All of the specified conditions in this classificati on rule must be satisfied with the rule to take effect. 5.4.6 Routing ...
-
TP-Link TD-W8900G - page 53
TD-W8900G 54M Wireless ADSL2+ Router User Guide 46 Figure 5-33 5.4.6.1. Default Gateway Choose “ Ad vanced Set up ” Æ “ Routing ” Æ “ Defau lt Gatewa y ”, you can see the Default Gateway screen, this screen allows you to configure the default gateway (shown in Figure 5- 34). Figure 5-34 If the Enable automatic Assigned Default Gatew a ...
-
TP-Link TD-W8900G - page 54
TD-W8900G 54M Wireless ADSL2+ Router User Guide 47 enabled PVC(s). If the check-box is not selected, enter the static Default Gateway IP and/or a WAN Interface , you can leave the WAN Interface default. Then click Save/Appl y butt on to save it. ) Note: If changing the Automatic Assigned Default Gateway from unselected to selected, you have to rebo ...
-
TP-Link TD-W8900G - page 55
TD-W8900G 54M Wireless ADSL2+ Router User Guide 48 2. Enter the following data: ¾ Destination Network Address: The Destination Network Address is the address of the network or host that you want to assign to a static route. ¾ Subnet Mask: The Subnet Mask determines whi ch portion of an IP Addre ss is the network portion, and which portion is the ...
-
TP-Link TD-W8900G - page 56
TD-W8900G 54M Wireless ADSL2+ Router User Guide 49 5.4.7 DNS When you select the connection type PPPoE, PPPoA , MER or IPoA for WAN configuration, you will see the DNS menu in the Web-based Utility (shown in Figure 5-38). It includes DNS Server and Dynamic DNS submenus. Figure 5-38 5.4.7.1. DNS Server Choose “ Advanced Setu p ” Æ “ DNS ” ? ...
-
TP-Link TD-W8900G - page 57
TD-W8900G 54M Wireless ADSL2+ Router User Guide 50 ) Note: You have to reboot the Router to make the new configuration take effect. 5.4.7.2. Dynamic DNS Choose “ Ad vanced Set up ” Æ “ DNS ” Æ “ Dynamic DNS ”, you can see the D ynamic DNS screen, this screen allows you to confi gure the Dynamic DNS (shown in Figure 5-40). The Router o ...
-
TP-Link TD-W8900G - page 58
TD-W8900G 54M Wireless ADSL2+ Router User Guide 51 Figure 5-41 ) Note: This page allows you to add a Dynamic DNS address from DynDNS.org,TZO or No-IP . 2. Select D-DNS provider (DynDNS.org,TZO or No-IP) in the drop-down list. 3. Enter the Hostname of the DNS Server, and select the corresponding Interface for the DDNS, you can leave it default. 4. T ...
-
TP-Link TD-W8900G - page 59
TD-W8900G 54M Wireless ADSL2+ Router User Guide 52 Figure 5-42 You can select the modulation type, phone line pair and the capabilit y of Bitswap or SRA. After you set them up, click the Save/Apply button to save the configurations. 5.4.9 Port Mapping Choose “ Advanced Setup ” Æ “ Port Mapping ”, you can see the Port Mapping screen, this s ...
-
TP-Link TD-W8900G - page 60
TD-W8900G 54M Wireless ADSL2+ Router User Guide 53 Figure 5-43 Click the Add/Edit button, and then you can configure the Port Mapping in the next screen (shown in Figure 5-44). After you confi gure the settings, click the Save/Appl y button to sa ve it. ...
-
TP-Link TD-W8900G - page 61
TD-W8900G 54M Wireless ADSL2+ Router User Guide 54 Figure 5-44 ...
-
TP-Link TD-W8900G - page 62
TD-W8900G 54M Wireless ADSL2+ Router User Guide 55 5.5 Wireless LAN Configuration The menus used to configure Wirele ss LAN settings available in t he Wireless directory including Basic, Security, MAC Filter, Ad vanced, and Statistics menus. The Wireless Basic, Security, MAC Filter, Advanced, and Statis tics are described below. 5.5.1 Wireless – ...
-
TP-Link TD-W8900G - page 63
TD-W8900G 54M Wireless ADSL2+ Router User Guide 56 ¾ Region: Restrict the channel set and transmit power. Click " Apply " to configure the basic wireless options. 5.5.2 Wireless – Security Choose “ Wireless ” Æ ” Security ”, you will see the screen of Wireless-Security settings shown as below. Figure 5-46 This page allows you ...
-
TP-Link TD-W8900G - page 64
TD-W8900G 54M Wireless ADSL2+ Router User Guide 57 Figure 5-47 ¾ Encryption strength: Select the appropriate level of enc ryption, 64-bit, 128-bit or 152-bit. ¾ Current Netw ork Key: To indicate which WEP key to use, select a transmission key number. ¾ Network Key 1-4: If you want to manually enter the WEP keys, then enter them in the network Ke ...
-
TP-Link TD-W8900G - page 65
TD-W8900G 54M Wireless ADSL2+ Router User Guide 58 3. In Network key 1 list, enter 5 ASCII c haracters or 10 hexadecim al digits for 64-bit encryption keys, enter 13 ASCII characte rs or 26 hexadecimal digits for 128-bit encryption keys, enter 16 ASCII characte rs or 32 hexadecimal digits for 152-bit encryption keys. 4. Click the Save/Apply button ...
-
TP-Link TD-W8900G - page 66
TD-W8900G 54M Wireless ADSL2+ Router User Guide 59 Figure 5-49 ¾ WPA Group ReKey Interval: Enter the Key Renewal period, wh ich tells the Router how often it should change encryption keys. ¾ RADIUS Server IP Address: The IP address of the RADIUS server. ¾ RADIUS Port: The port of the RADIUS server. The default number is 1812. ¾ RADIUS key: The ...
-
TP-Link TD-W8900G - page 67
TD-W8900G 54M Wireless ADSL2+ Router User Guide 60 Figure 5-50 5.5.2.3. WPA-PSK WPA-PSK requires a shared key and does not use a separate server for aut hentication. PSK keys can be ASCII or Hex type. Figure 5-51 ¾ WPA Pre-Shared Key: Enter the key shared by the Router and your other network devices. It must have 8-63 ASCII characters or 64 Hexade ...
-
TP-Link TD-W8900G - page 68
TD-W8900G 54M Wireless ADSL2+ Router User Guide 61 ASCII or Hex type. 3. Change the Group Ke y Interval as desired or use the default setting. 4. Click the Save/Apply button to save the new configuration. Figure 5-52 ) Note: If you click the option “ Click here to display ”, the Figure 5-53 will pop-up, and it shows the password you have set. F ...
-
TP-Link TD-W8900G - page 69
TD-W8900G 54M Wireless ADSL2+ Router User Guide 62 Figure 5-54 5.5.2.5. WPA2-PSK To configure WPA2-PSK settings, select the WPA2-PSK option from the drop-down list. The menu will change to offer the appropriate settings . WPA2-PSK requires a shared key and does not use a separate server for authentication. PSK keys can be ASCII or Hex type. Figure ...
-
TP-Link TD-W8900G - page 70
TD-W8900G 54M Wireless ADSL2+ Router User Guide 63 Figure 5-56 5.5.2.7. Mixed WPA2/WPA-PSK To configure Mixed WPA2/WPA-PSK settings, select the Mixed WPA2/WPA-PSK option from the drop-down list. The menu will change to offer the appropriate settings. The steps of this setting are the same with WPA-PSK. Figure 5-57 5.5.3 Wireless -- MAC Filter Choos ...
-
TP-Link TD-W8900G - page 71
TD-W8900G 54M Wireless ADSL2+ Router User Guide 64 Figure 5-58 Wireless access can be filtered by using the MAC addresses of the wireless devices transmitting within your network’s RADIUS. To filter wire less users by MAC Address, either permitting or blocking access. If you do not wish to filter users by MAC Address, select Disabled. ¾ Allow: C ...
-
TP-Link TD-W8900G - page 72
TD-W8900G 54M Wireless ADSL2+ Router User Guide 65 Figure 5-60 ¾ Channel: Select the channel you want to use from the drop-dow n List of Channel. This field determines which operating frequen cy will be used. It is not necessary to change the wireless channel unless you notice interferenc e problems with another nearby access point. ¾ Fragmentati ...
-
TP-Link TD-W8900G - page 73
TD-W8900G 54M Wireless ADSL2+ Router User Guide 66 the Router. 5.5.5 Wireless – Statistics Choose “ Wireless ” Æ ” Statistics ”, you will see the screen of Wireless-Statistics setting shown as below. Figure 5-61 This page shows authenticated wirele ss stations and their status. ¾ BSSID: Displays the connected wire less station's MA ...
-
TP-Link TD-W8900G - page 74
TD-W8900G 54M Wireless ADSL2+ Router User Guide 67 5.7 Management Choose “ Management ”, there are six submenus under the main menu. They are Settings , System Log , TR-069 client , Internet Time , Access Control , Update Software and Reboot . Click any of them, and you will be able to configure the corre sponding function. 5.7.1 Settings This ...
-
TP-Link TD-W8900G - page 75
TD-W8900G 54M Wireless ADSL2+ Router User Guide 68 Figure 5-65 2. Click the Save button, and save the file as the appointed file (shown in Figure 5-66). Figure 5-66 5.7.1.2. Update Choose “ Management ” Æ “ Settings ” Æ “ Update ”, you can see the Update screen, this screen (shown in Figure 5- 67) allows you to update the Router’s s ...
-
TP-Link TD-W8900G - page 76
TD-W8900G 54M Wireless ADSL2+ Router User Guide 69 Figure 5-67 To update the Router’s settings: 1. Click the Brow se button to locate the update file for the device, and you can also enter the exact path to the Setting file in the text box. 2. After you have selected the file for updating the settings, click the Update S ettings button. ) Note: T ...
-
TP-Link TD-W8900G - page 77
TD-W8900G 54M Wireless ADSL2+ Router User Guide 70 Figure 5-69 T o View the System Log: Click the Vie w System Log button, you will see the screen (shown in Figure 5-70) which displays the Router ’s recent logs. Figure 5-70 ¾ Refresh: Click the button, the informati on in the table will be updated. ¾ Close: Click the button, the screen will be ...
-
TP-Link TD-W8900G - page 78
TD-W8900G 54M Wireless ADSL2+ Router User Guide 71 Figure 5-71 ¾ Disable/Enable: Select the Enable to log the events, if you don’t want to log these event s, please select Disable . ¾ Log Level: Select the Log level in the drop-down list, for the Log level, all events above or equal to the selected level will be logged. ¾ Display Level: Select ...
-
TP-Link TD-W8900G - page 79
TD-W8900G 54M Wireless ADSL2+ Router User Guide 72 Figure 5-72 To set the Router’s time: 1. Select automatically synchronize with Internet time servers. 2. Select the First NTP time server and/or t he Second NTP time server in the drop-down list severally. 3. Select your local time zone. 4. Click Save/Apply button. ) Note: a) This setting will be ...
-
TP-Link TD-W8900G - page 80
TD-W8900G 54M Wireless ADSL2+ Router User Guide 73 Figure 5-73 ¾ Inform: You can select the checkbox to disable or enable the Inform Interval. ¾ Inform Interval: Type the interval time of your Router contact with the ACS . ¾ ACS URL: Please accept this information from your ISP. And through ACS (Auto-Configuration Server) you can perform auto-co ...
-
TP-Link TD-W8900G - page 81
TD-W8900G 54M Wireless ADSL2+ Router User Guide 74 5.7.5 Access Control This section provides three submenus including Services , Addresses and Passw ord (shown i n Figure 5-74), the detailed descriptions are provided below. Figure 5-74 5.7.5.1. Services Choose “ Management ” Æ “ Acces s Control ” Æ “ Services ”, you can see the Servi ...
-
TP-Link TD-W8900G - page 82
TD-W8900G 54M Wireless ADSL2+ Router User Guide 75 screen, this screen (shown in Figure 5-76) allows you to conf igure the IP Address for managing the Router. Figure 5-76 To add the IP Address: 1. Click the Add button. You can add a new IP Address in the next screen (shown in Figure 5-77 ). Figure 5-77 2. Enter the IP address of the managem ent sta ...
-
TP-Link TD-W8900G - page 83
TD-W8900G 54M Wireless ADSL2+ Router User Guide 76 Figure 5-78) which allows you to change t he factory default password of the Router. Figure 5-78 To change the password: 1. Enter the Old Password in the text box. 2. Enter the Ne w Pa ss wo r d and Confirm Pass w ord . The Confirm Password should be the same as the New Password. 3. Click the Save/ ...
-
TP-Link TD-W8900G - page 84
TD-W8900G 54M Wireless ADSL2+ Router User Guide 77 ¾ Up date Sof tware: After you have selected the latest sof t ware, click the button. To update the Router's software: 1. Downl oad the latest software upgrade file from the TP-LINK website ( www.tp-link.com). 2. C lick Bro w se to view the folders and select the image file or enter the exact ...
-
TP-Link TD-W8900G - page 85
TD-W8900G 54M Wireless ADSL2+ Router User Guide 78 Chapter 6. Appendix Appendix A: Glossary Access Point - A device that allows wireless-equipped computers and other devices to communicate with a wired network. Also us ed to expand the range of a wireless network. Ad-hoc Netw ork - An ad-hoc network is a group of co mputers, each with a wireless ad ...
-
TP-Link TD-W8900G - page 86
TD-W8900G 54M Wireless ADSL2+ Router User Guide 79 Ethernet - IEEE standard network protocol that specifies how data is placed on and retrieved from a common transmission medium. Firewall - A set of related programs located at a net work gateway server that protects the resources of a network from users from other networks. Gateway - A device that ...
-
TP-Link TD-W8900G - page 87
TD-W8900G 54M Wireless ADSL2+ Router User Guide 80 adapters. PPPoE ( P oint to P oint P rotocol o ver E thernet) - PPPoE stands for Point to Point protocol over Ethernet, this protocol is used as a type of broadband connection that provides authentication (username and password) in addition to data transport. PPPoA (P oint to P oint P rotocol over ...
-
TP-Link TD-W8900G - page 88
TD-W8900G 54M Wireless ADSL2+ Router User Guide 81 VLAN ID (0-4095) - Indicates the ID number of the VLAN being configured. Up to 256 VLANs can be created. WAN ( W ide A rea N etwork) - Networks that cover a large geographical area. Web-based Utility - The web page that allows you to manage the Router. WEP (W ired E quivalent P rivacy ) - A data pr ...
-
TP-Link TD-W8900G - page 89
TD-W8900G 54M Wireless ADSL2+ Router User Guide 82 Appendix B: S pecifications Supporting Standards and Protocols ANSI T1.413, ITU G.992.1, IT U G.992.2, ITU G.992.3, ITU G.992.5, IEEE 802.11b , IEEE 802.11g , IEEE 802.3, IEEE 802.3u, TCP/IP, IPoA , PPPoA , PPPoE, SNTP, HTTP, DHCP, ICMP, N AT LAN Ports 4 10/100M Auto-Negotiation RJ45 ports （ Auto ...
Avez-vous une question à propos de TP-Link TD-W8900G?
Utiliser le formulaire ci-dessous
Si vous n’avez pas résolu votre problème avec TP-Link TD-W8900G, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec TP-Link TD-W8900G il est probable qu’il a envie de partager la façon de le résoudre.