Français dropdown-ico

Manuel d’utilisation Drolet 1800 EPA

40 pages 0.71 mb
Télécharger

Aller à la page of 40

Summary
  • Drolet 1800 EPA - page 1

    READ AND KEEP THIS MANUAL FOR REFERENCE OWNER’S MANUAL ESCAPE 1800 EPA WOOD STOVE US ENVIRONMENTAL PROTECTION AGENCY PHASE II CERTIFIED WOOD STOVE Verified and tested following ULC S627 and UL 1482 Standards by: Manufactured by : STOVE BUILDER INTERNATIONAL INC. 1700, Léon-Harmel, Québec (Québec) G1N 4R9 Tel : (418 ) 527-3060 Fax : (418 ) 527- ...

  • Drolet 1800 EPA - page 2

    1 INTRODUCTION Stove Builder International, one of the most im portant wood stove and fireplace manufacturers in North America, congratulates you on your purch ase and wishes to help you get maxim um satisfaction from your wood stove. In the pa ges that follow, we will give you advice on wood heating and controlled combustion as well as t echnical ...

  • Drolet 1800 EPA - page 3

    2 TABLE OF CONTENTS 1.1 GENERAL INST ALLATION ........................................................................................................... ........... 3 1.2 POSITIONING THE ST OVE.......................................................................................................... ............. 4 1.3 CLEARANCES .................. ...

  • Drolet 1800 EPA - page 4

    3 SECTION 1.0 - INSTALLATION When installed and operated as described in th ese instructions, the Escape 1800 EPA wood stove is suitable for use as a freestanding wood stove in residential installations. The Escape 1800 EPA wood stove is not intended for installation in a bedroom or a mobile hom e. In Canada, the CSA B365 Installation Code for Soli ...

  • Drolet 1800 EPA - page 5

    4 1.2 POSITIONING THE STOVE It is very important to position the wood stove in an area that will favour the m ost efficient heat distribution throughout the house. The stove should therefore be installed in the room where the most time is spent, and in the m ost spacious room possible. Recall that wood stoves produce radiating heat, the heat we fee ...

  • Drolet 1800 EPA - page 6

    5 Figure 1.3 Clearances to combustible materials ...

  • Drolet 1800 EPA - page 7

    6 1.3.1 Reduced clearances using shielding You may decrease the minim um clearances to com bustible materials by installing heat radiation shields between the walls or the ceiling and the stove. Those heat radiation sh ields must be installed permanently, and must be made of a heat-resistant or heat-tolerant material. Consult the table below: Reduc ...

  • Drolet 1800 EPA - page 8

    7 1.4 FLOOR PROTECTOR If the stove is to be installed on top of a com bustible floor, it must be guarded by a non-com bustible material extending at least 18” (300mm ) from the fr ont and 8” (200mm ) from the sides and the back of the firebox., as shown in Figure 1.4 below. Please note that a floor protection is required with the pedestal model ...

  • Drolet 1800 EPA - page 9

    8 SECTION 2.0 CHIMNEY (FLUE SYSTEM) 2.1 DEFINITIONS For clarity, the following definitions should be used with respect to these instructions: • A chimney system consists of a connector off the top of the stove, and a chimne y , which attaches to the connector and terminates outside the house. • A chimney can be a masonry chimney (of masonry con ...

  • Drolet 1800 EPA - page 10

    9 If you are using a masonry chimney, it is im porta nt that it be built in compliance with the specifications of the Building Code. It must be lin ed with f ire clay bricks, or clay tiles, sealed together with fire cement, or have a listed solid fuel burning stainless steel liner. Round chim neys are the most efficient. The interior diameter of th ...

  • Drolet 1800 EPA - page 11

    10 FIGURE 2.2 Minimum Height of the Chimney 2.2.1 Step by step installation of your factory-built chimney The way to install your chimney may vary from one chim ney manufacturer to another. The instructions contained i n this manual ar e based on the re comme ndations of chimney manufacturers whose products are sold at many North American retailers ...

  • Drolet 1800 EPA - page 12

    11 Typical installation through the wall FIGURE 2.2.1 (A) Typical installation through the wall 1- Start by positioning your stove where you would like it to go, taking into account the minimum clearances to combustible material. You will then be able to determin e where the chim ney will pass through the wall. You will probably have to adjust the ...

  • Drolet 1800 EPA - page 13

    12 2- Once the opening completed, you need to frame in the area to allow for the installation of a w all thimble. A wall thimble is not required for installations through concrete walls. 3- You m ust first secure the wall thimble into th e exterior wall surface. Then, do the same inside and fasten the trim plate. 4- Then, from outside the building, ...

  • Drolet 1800 EPA - page 14

    13 6- You can start to add chimney sections. W e recomm end that you also use locking bands to secure all connections. You w ill need to secure the chimney to the house using wall bands. Wall bands wrap around the chimney and then attach to the wall. Install the first one 3 feet above the wall support. Then, you will need another band for each 8 fe ...

  • Drolet 1800 EPA - page 15

    14 8- Finally, twist on your rain cap and you can head back inside. 9- You are now ready to connect your chimney to your stove. Simply install the inter-connecting stove pipe between the stove pipe adapter and the stove. You can follow the instructions in the following section (section 2.3) of this manual called « CHIMNEY CONNECTOR». Ceiling supp ...

  • Drolet 1800 EPA - page 16

    15 Typical installation through the ceiling FIGURE 2.2.1 (B) Typical Installation Through the Ceiling 1. Place your stove where you would like it located and use a plumb line to mark the ceiling directly above your stove flue. You will probably ha ve to adjust this position slightly to en sure that your chimney will run between the joists . You can ...

  • Drolet 1800 EPA - page 17

    16 2. Before you install the ceiling support, you need to frame the area. 3. To install the ceiling support, just slide the a ssembly into the framed opening from below. Once you ensure that the finishing plate is flus h with the underside of the ceiling and assembly is level, secure it with screws. 4. Once the support is secure, you can begin to a ...

  • Drolet 1800 EPA - page 18

    17 6. Now, you can add additional chim ney sections. Continue adding chim ney lengths until a height of about 2 feet below the next ceiling level. An attic insulation shield must be installed where a chimney passes from a lower living space into an upper living space or attic space. It is designed to keep insulation materials away from the chim ney ...

  • Drolet 1800 EPA - page 19

    18 9. You are now ready to connect your chimney to your stove. Sim ply install the inter-connecting stove pipe between the stove pipe adapter and the stove. You can follow the instructions in the following section (section 2.3) of this manual called « CHIMNEY CONNECTOR». 2.2.2 Typical installation through an existing masonry chimney You can also ...

  • Drolet 1800 EPA - page 20

    19 FIGURE 2.2.2 (A) Typical Installation Through an Existing Masonry Chimney ...

  • Drolet 1800 EPA - page 21

    20 FIGURE 2.2.2 (B) Factory Built Thimble ...

  • Drolet 1800 EPA - page 22

    21 FIGURE 2.2.2 (C) Brick Thimble 2.3 CHIMNEY CONNECTOR Your chimney connector (comm only called stove pipe) and chimney must have the same diameter as the stove’s exhaust outlet. The stove pipe must be m ade of aluminized or cold roll steel with a minimum 24-gauge thickness (0.021" or 0.53 mm). It is strictly forbidden to use galvanized ste ...

  • Drolet 1800 EPA - page 23

    22 FIGURE 2.3 (A) Connecting Sections 1/4" RISE PER FOOT FIGURE 2.3 (B) Minimum Slope ...

  • Drolet 1800 EPA - page 24

    23 2.4 DRAFT Your E.P.A Drolet stove’s performance will be optim ised if it is installed with a chimney (flue) system that provides an adequate draft. The draf t is the force that m oves air from the appliance up through the chimney and is predominantly affected by the height and diam eter of the chimney, as well as the stack temperatures of the ...

  • Drolet 1800 EPA - page 25

    24 2.6 THE ADVANTAGE OF INSTALLING A BLOWER (FAN) A blower can be installed at the back of your E. P.A Drolet stove. This option is necessary if you wish to redistribute into a room the heat trapped at the back of your stove. By forcing hot air toward the front, the blower enables you to extend the ra diation and convection power of your stove. You ...

  • Drolet 1800 EPA - page 26

    25 SECTION 3.0 OPERATION Keep these instructions for future reference. WARNING: • ANY MODIFICATION OF THE APPLIANCE THAT HAS NOT BEEN APPROVED IN WRIT ING BY THE TESTING AUTHORITY IS CONSIDERED AS BREACHING CSA B365 ( CANADA ), AND ANSI NFPA 211 (USA). • DO NOT USE FLAMMABLE LIQUIDS OR AEROSOLS TO START OR REKINDLE T HE FIRE . • DO NOT USE FL ...

  • Drolet 1800 EPA - page 27

    26 3.1 SAFETY INFORMATION • These stoves are designed for safe operation WHEN BURNING WOOD ONLY . Altering or modifying the unit or installation without pr oper authorisation will void the certification, warranty, and safety listing, and may result in a safety hazard. • For safety reasons, never lea ve the unit unattende d with the door open or ...

  • Drolet 1800 EPA - page 28

    27 • Although the ceramic glass is extremely durabl e under any norm al use, a few precautions are required. Do not attempt to push logs further into the fire by using the door, as the glass may break if any solid object heavily contacts it. • Never operate the stove with the door open, or cracked slightly open, except briefly during the lighti ...

  • Drolet 1800 EPA - page 29

    28 Wood species Energy yield (millions of BTU/cord) Oak 29 Sugar Maple 28 Beech 26 Yellow birch 25 Ash 24 High energy yield Elm 23 Larch (Tamarack) 23 Red Maple 23 Douglas red fir 23 Silver birch 22 Alder 18 Poplar 17 Medium energy yield Hemlock 17 Spruce 17 Pine 17 Bass 16 Low energy yield Fir 13 Data provided by Energy, Mines and Resources – Ca ...

  • Drolet 1800 EPA - page 30

    29 3.2.2 Simple wood moisture test Add one large piece of wood to the top of an establishe d fire. If it starts to burn on three sides within one minute, it is dry and seasoned and right for burni ng. If it turns black and starts to burn in about three minutes or more, it is dam p. If it turns bl ack and does not start burning until five minutes or ...

  • Drolet 1800 EPA - page 31

    30 Intensity Draft Setting Low Push Control to end of travel. Medium Low Pull Control by 3/8” from closed position. Medium High Pull Control by 3/4” from closed position High Pull Control to end of travel. Table 3.4 Closing the draft control down too soon will lower combustion efficiency, and may result in creosote build-up in the chimney (whic ...

  • Drolet 1800 EPA - page 32

    31 3.5 MAINTAINING THE FIRE Once the wood has been consumed (or partially consum ed) and you have obtained a good bed of embers, you should reload the unit. In order to do so, open the air control to its maxim um for approximately 15 seconds prior to opening the st ove door. Then, proceed by opening the door very slowly. Open it by 2” to 4” (52 ...

  • Drolet 1800 EPA - page 33

    32 SECTION 4.0 MAINTENANCE 4.1 CLEANING AND PAINTING YOUR STOVE Clean the stove frequently so that soot, ash, and creosote do not accumulate. Do not attempt to clean the stove when the unit is hot. Special care mu st be taken with plated surfaces in order to maintain the finish at its original brilliance. Do not use an abrasive cleaner which will s ...

  • Drolet 1800 EPA - page 34

    33 4.3 GASKETING It is recommended that you change the door gasket (which makes your stove door air tight) once a year, in order to insure good control over the co mbustion, m aximum efficiency and security. To change the door gasket, simply remove the dam age d one. Carefully clean th e gasket groove, apply a high temperature silicone sold for thi ...

  • Drolet 1800 EPA - page 35

    34 4.5 CHIMNEY (FLUE) CLEANING Regular chimney (flue) maintenance, as well as good burning practices, are required to prevent chimney fires. When wood (especially green wood) is burned without adequate heat or air supply, it produces tar and other organic vapours ( smoke ), which combine with expelled mo isture to form creosote. The creosote vapour ...

  • Drolet 1800 EPA - page 36

    35 4.6 BAFFLE INSTALLATION FOR ESCAPE 1800 MODEL All firebrick and ceramic wool baffles must be properly in place for correct burning operation. Have any damaged firebricks replaced. Check the firebricks annually for damage and replace if they are broken or damaged. See figure 4.6.1 (B) for the firebrick layout. Figure 4.6.1 (A) – Baffle installa ...

  • Drolet 1800 EPA - page 37

    36 Figure 4.6.1 (B) - Firebrick layout for Escape 1800 model ...

  • Drolet 1800 EPA - page 38

    37 4.5 SECONDARY AIR TUBE REPLACEMENT (see Figure 4.11) 1. Remove cotter pin at RH end of tube. 2. Slide tube to left and lower tube end below RH plenum. 3. Slide tube to right to remove. 4. Reassemble in reverse order using a new co tter pin. The cotter pin is a hamm erlock style and locks into place by hitting the head sharply with a hammer. 5. N ...

  • Drolet 1800 EPA - page 39

    38 SECTION 5.0 SPECIFICATIONS Fuel Type Cordwood Test Standards ULC S627 (CSA B366.2) & UL 1482 residential. Heat Output Maximum of 68000 BTU/hr . EPA test (63% default efficiency). Maximum of 75000 BTU/hr. with seasoned cordwood. Range Will vary with usage depending on the type and condition of cord wood. Shipping Weight 421 lbs (191 kg) Fireb ...

  • Drolet 1800 EPA - page 40

    39 1700, Léon-Harmel street, Quebec (Quebec) G1N 4R9 tel. : (418) 527-3060 fax : (418) 527-4311 e-mail : tech@sbi-international.com web site : ht tp :/ /www.d ro le t. ca LIMITED LIFETIME WARRANTY The warranty of the manufacturer extends only to the original consumer purchaser and is not transferable. This warranty covers brand new products only, ...

Fabricant Drolet Catégorie Stove

Les documents que nous recevons du fabricant de l'appareilDrolet 1800 EPA peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Drolet
- manuels d’utilisations 1800 EPA
- fiches produit Drolet
- dépliants
- ou étiquettes-énergie Drolet 1800 EPA
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Drolet 1800 EPA.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Drolet 1800 EPA, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Drolet 1800 EPA. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Drolet 1800 EPA.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Drolet 1800 EPA, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Drolet 1800 EPA par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Drolet 1800 EPA.

Le manuel d’utilisation complet Drolet, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Drolet 1800 EPA - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Drolet 1800 EPA, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lDrolet 1800 EPA qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Drolet 1800 EPA - qui devraient nous aider dans les premières étapes lors de l'utilisation Drolet 1800 EPA
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Drolet 1800 EPA
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Drolet 1800 EPA dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Drolet 1800 EPA?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Drolet 1800 EPA, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Drolet 1800 EPA il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)