Français dropdown-ico

Manuel d’utilisation RedMax HC510DV

44 pages 1.52 mb
Télécharger

Aller à la page of 44

Summary
  • RedMax HC510DV - page 1

    OWNER / OPERA T OR MANUAL CUT -OFF SA W T2069-93110 (310) HC510DV The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. W ARNING Before using our products, please read this manual carefully to understand the proper use of your unit. W ARNING Diamond wheel ...

  • RedMax HC510DV - page 2

    ...

  • RedMax HC510DV - page 3

    SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. ■ WARNINGS IN THE MANUAL This mark indicates i ...

  • RedMax HC510DV - page 4

    2. Specifications Model Name and Number ···································································CUT-OFF SAW, HC510DV Overall Size (with 14 in. Blade)(LxWxH) ························· 29.4(735)x9.4(235)x19.8(495) in. (mm) Dry Weight (excluding Blad ...

  • RedMax HC510DV - page 5

    If warning label peel off or become soiled and impossible to read, you should contact the dealer from which you purchased the product to order new labels and affix them in the required location(s). Never modify your machine. We won't warrant the machine, if you use the remodeled machine or you don't observe the proper usage written in the ...

  • RedMax HC510DV - page 6

     6  For safe operation and maintenance, symbols are indicated on the machine. According to these indications, please be careful not to take a mistake. (a) The port to refuel the "MIX GASOLINE" Position: FUEL TANK CAP (b) Choke will close when pulling the choke knob Position: CHOKE KNOB (c) It indicates the start (I) and stop (O) dir ...

  • RedMax HC510DV - page 7

     7  5. For safe operation ■ BEFORE USING THE MACHINE a. Cut-off saws are high-speed cutting tools and very dangerous to operate; therefore it is very important that you read and fully understand the contents of the owner’s manual before using. b. This unit has been designed for use in cutting concrete products, stone and cast-iron pipe at ...

  • RedMax HC510DV - page 8

     8  exposes the operator to Whitefinger disease. This condition produces numerous burning sensations and interferes with the ability to feel and regulate temperature. Get medical advise at once if you experience these symptoms. h. Be sure to keep this manual handy so that you may refer to it later whenever any questions arise. i. Always be su ...

  • RedMax HC510DV - page 9

    refill the tank of the unit in any place where there is a boiler, stove, wood fire, electrical sparks, welding sparks, or any other source of heat or fire which might ignite the fuel. 2. Never smoke while operating the unit or refilling its fuel tank. 3. When refilling the tank, always turn off the engine and allow it to cool down. Take a careful l ...

  • RedMax HC510DV - page 10

     10  the other one’s presence and how to sign the danger etc. d. Fix the cutting object if it is unfixed. e. Never operate the engine without wheel guard. f. Adjust the wheel guard to deflect sparks, dust, and material away from the operator and flammable materials. g. Inspect the entire unit for loose fasteners and fuel leakage. Make sure ...

  • RedMax HC510DV - page 11

    i. Do not cut above shoulder height. j. If someone calls out while working or if you wish to continue work in another spot, or if you want to check the unit, always be sure to turn off the engine before making your next move. k. Never touch the spark plug or plug cord while the engine is in operation. Doing so may result in being subjected to an el ...

  • RedMax HC510DV - page 12

    Use adequate cutter blades suited to materials to be cut. Use of inadequate cutter blades may cause irregular wear of blades, poor cutting performances, or irregular overheating, etc. Continuance of those inadequate operations may damage the blades and cause serious accidents. ■ CHANGE OF DUST STOPPER • To apply 12 inch blades, the dust stopper ...

  • RedMax HC510DV - page 13

    ■ MOUNTING OF CUTTER BLADE The flange bolt shall be securely fixed. (Fixing torque: 266~434 in-lbs (30~50 N·m)) Insufficient fixing of the bolt may cause brake away of the blade and is extremely dangerous. 1. Unscrew a flange bolt and remove flange washer (A). 2. Mount a cutter blade on flange washer (B) aligning its centre hole correctly with a ...

  • RedMax HC510DV - page 14

     14  7. Fuel ■ RECOMMENDED MIXING RATIO GASOLINE 50:OIL 1 • Exhaust emission are controlled by the fundamental engine parameters and components(eq., carburation, ignition timing and port timing) without addition of any major hardware or the introduction of an inert material during combustion. • These engines are certified to operate on ...

  • RedMax HC510DV - page 15

    7. Fuel  15  again for at least one minute. As some oils may be difficult to agitate depending on oil ingredients, sufficient agitation is necessary for the engine to last long. Be careful that, if the agitation is insufficient, there is an increased danger of early piston seizing due to abnormally lean mixture. 5. Put a clear indication on t ...

  • RedMax HC510DV - page 16

     16  ■ STARTING ENGINE •B efore starting the engine, check if there is any problem such as loose fitting of cutter blade or fuel leakages. •P lace the machine on the ground and hold securely when starting. Do not start the engine while hanging it by one hand because the cutter blade may contact with the ground or other obstacles. • As ...

  • RedMax HC510DV - page 17

    8. Operation In case of restarting immediately after stopping the engine, pull the starter knob with the choke knob pushed in (choke open). 4. Push down a safety lock above the rear handle and pull the throttle lever. Push in a start setting button and set the throttle lever to a starting position. (OP3) (1) Safety lock (2) Start setting button (3) ...

  • RedMax HC510DV - page 18

     18  pulled, push in the choke knob and pull the rope until it starts. Otherwise, remove a spark plug to dry its electrode, and reassemble. Try again the starting operation. 8. When the engine is started, lightly pull the throttle lever and unlock the start setting button. In case of cold start of the engine, apply 1~2 minutes of warming up o ...

  • RedMax HC510DV - page 19

     19  8. Operation ■ CUTTING OPERATION • For cutting, hold the machine in your body centre and lead the dust hose through both legs. Lightly bend the knees and keep a stable posture. •W hen applying the cutter blade to a work, start with low speed to form a guide notch, and then cut with full throttle. Do not forcedly press the cutter bl ...

  • RedMax HC510DV - page 20

     20  9. Maintenance • Be sure to stop the engine for check and maintenance. • Do not modify the machine nor disassemble the engine. •U se RedMax genuine or specified spare parts and oils. ■ AIR CLEANER The air cleaner is adhered with much dusts produced by a cutting operation. At the end of day’s operation, be sure to check and clea ...

  • RedMax HC510DV - page 21

    or damaged. • Avoid dusts to penetrate into the engine when removing the air filter. Cover an air inlet with a cloth after removing the filter. • To keep the engine performance, change the air filter at every 20 hours of operation. ■ SPARK PLUG Do not touch the spark plug by bare hands immediately after stopping the engine. There is a danger ...

  • RedMax HC510DV - page 22

     22  ■ COOLING AIR PASSAGE • Do not touch the cylinder, muffler or spark plug by bare hands immediately after stopping the engine. There is a danger of burn for its high temperature. • On the starting inspection, check the muffler and clean if there are adhered wood chips or dry leaves. Those may cause overheating of the muffler. Also t ...

  • RedMax HC510DV - page 23

    9. Maintenance This machine is equipped with a spring loaded semi-automatic tensioner. Therefore, by slackening cutting head fixing nuts and bolts, correct tension is always maintained. (MA6) Apply following procedures if readjustment is required: (1) Cutting head (2) Spring (3) Drive case 1. Slacken 3 pieces of flange nuts which are holding the cu ...

  • RedMax HC510DV - page 24

     24  MA11 9. Maintenance 3. Slacken a stay bolt on opposite side and remove together with a washer. (MA10) (1) Stay (2) Washer (3) Bolt 4. Slacken a semi-auto tensioner bolt using angle wrench. Push the cutting head toward the engine while swinging it up and down to slacken the belt tension. (MA11) (1) Push toward the engine (2) Bolt (3) Slac ...

  • RedMax HC510DV - page 25

    MA14 9. Maintenance 2. Put the belt into a pulley groove on the main body. Then engage fan drive spline axle of the drive case with splines on the main body. 3. Assemble the drive case to the main body with 2 nuts and 4 screws. 4. Put the belt into the cutting head pulley. 5. Apply tension on the belt by screwing in the belt tensioner bolt to the e ...

  • RedMax HC510DV - page 26

     26  9. Maintenance 4. Tighten the centre bolt of the idler pulley to fix the belt adjustment plate. 5. Fit the belt cover as original. ■ ENGINE ADJUSTMENT (MA15) It is dangerous if the cutter blade continues to turn even fingers are removed from the throttle lever. In case it is not solved by readjusting an idle adjust screw with following ...

  • RedMax HC510DV - page 27

    4. Make a test cut adjust the H needle for best cutting power, not for maximum speed. Standard Idle Speed: 2300~2700 rpm. (1) Idle adjust screw (T) (2) Low speed needle (L) (3) High speed needle (H) 9. Maintenance  27  ...

  • RedMax HC510DV - page 28

     28  9. Maintenance ■ STARTER ROPE EXCHANGE When exchanging the starter rope, pay attention so that built-in recoil spring does not jump out. Mistake in operation may end up with injury to the eye, etc. by jumped out spring. The starter rope wears and deteriorates with usage. In case the rope becomes shaggy or partially worn, suggest exchan ...

  • RedMax HC510DV - page 29

    9. Maintenance In case irregular wear is observed on a recoil boss or reel bore, exchange for new components. 5. Remove the rope from the reel. 6. Make a knot in end of new rope and lead it through a reel hole from outside. Pull the rope hard to engage the knot into a reel pit and put end of the knot into a reel notch. (MA19) (1) Notch In case the ...

  • RedMax HC510DV - page 30

     30  9. Maintenance rope slowly be retracted to the reel. 12. Pull the rope 2~3 times to confirm if it is fully retracted. If it is not fully retracted, pull it out halfway and while holding the reel with left hand, hitch the rope to the reel notch and turn additional 2~3 turns clockwise. Excessive turns of reel cause overload on the coil spr ...

  • RedMax HC510DV - page 31

    10. Storage When discharging fuel, be careful not to spill fuel and completely wipe off if spilled. Also, securely close a cap of storage tank. • In case the machine is left for long time, inside of the carburetor may be clogged and cause engine failure (starting failure or poor output power). • During storage, make fuel tank cap loose. If it i ...

  • RedMax HC510DV - page 32

     32  11 . T roubleshooting guide Case 1. Starting failure CHECK PROBABLE CAUSES ACTION fuel tank ➞ incorrect fuel ➞ drain it and with correct fuel fuel filter ➞ fuel filter is clogged ➞ clean carburetor adjustment screw ➞ out of normal range ➞ adjust to normal range sparking (no spark) ➞ spark plug is fouled/wet ➞ clean/dry ? ...

  • RedMax HC510DV - page 33

    12. Parts list NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/or replacement. 2. KOMATSU ZENOAH does not warrant the machines, which have been damaged by the use of any parts other than those specified by the company. 3. When placing parts orders for repair and/or replacement, check if the model name and th ...

  • RedMax HC510DV - page 34

    12. Parts list Fig.1 CUTTER UNIT HC510DV (S/N 200101 and up)  34  ...

  • RedMax HC510DV - page 35

    Key# Part Number Description Q'ty 1 2894-61100 CASE COMP 1 2 01252-60510 • BOLT 1 3 06004-06001 • BEARING 4 4 2670-21220 • SEAL 1 5 2894-64110 SHAFT, inlet 1 6 2894-64120 PULLEY 1 7 2894-64210 FAN 1 8 2894-64250 SPACER 1 9 2894-64300 SHAFT COMP 1 10 01643-30823 WASHER 1 11 3350-43231 NUT 1 12 2894-64410 COVER, fan 1 13 2894-64420 SEAL 1 ...

  • RedMax HC510DV - page 36

    Fig.2 POWER UNIT (1) HC510DV (S/N 200101 and up)  36  12. Parts list ...

  • RedMax HC510DV - page 37

    Key# Part Number Description Q'ty 61 2810-72110 • CAP 1 62 1400-72121 • SPRING 1 63 2670-71320 • TUBE 1 64 2810-71250 • GROMMET 1 65 2670-14220 SCREW M5x20 2 66 2670-71510 CORD 1 67 T2069-71600 SWITCH ASS'Y 1 71 2670-14130 SCREW 1 72 3699-90512 SPARKPLUG NGK BPM8Y 1 73 2810-21270 PLATE 1 74 0260-30410 SCREW 2 75 2884-75000 STARTER ...

  • RedMax HC510DV - page 38

    12. Parts list Fig.3 POWER UNIT (2) HC510DV (S/N 200101 and up)  38  ...

  • RedMax HC510DV - page 39

    Key# Part Number Description Q'ty Key# Part Number Description Q'ty 1 2884-31110 COVER, cylinder 1 2 2670-14320 SCREW M5x14 5 3 2884-82603 PLATE COMP 1 4 2884-82630 • SEAL 1 5 2884-82640 • SEAL, plate 1 6 2670-14320 SCREW M5x14 4 7 2884-83100 CLEANER COMP 1 8 2884-83121 • ELEMENT 1 9 2884-83301 PLATE ASS'Y 1 10 2884-83320 • B ...

  • RedMax HC510DV - page 40

    Key# Part Number Description Q'ty 1 T2069-81000 CARBURETOR ASS’Y (WT-648) – 2 3306-81380 • SCREEN 1 3 2810-81120 • COVER 1 4 3310-81130 • SCREW 1 5 T2050-06020 • GASKET KIT 1 6 3310-81230 • LEVER 1 7 3310-81240 • SCREW 1 8 2841-81270 • SPRING 1 9 3310-81250 • PIN 1 10 3310-81280 • COVER 1 11 3356-81310 • INLET VALVE 1 1 ...

  • RedMax HC510DV - page 41

     41  Key# Part Number Description Q'ty 1 2894-92310 PLATE for 12" 1 2 2894-68310 CLUMP 1 3 2894-68210 DUST HOSE 1 4 2894-68110 DUST BAG 1 5 3388-92110 MASK 1 6 6242-92110 GOGGLE 1 7 2894-91000 TOOL SET 1 8 3345-91110 • BAG 1 9 3320-91140 • PLUG WRENCH 1 10 3582-91330 • BAR 1 11 2670-91150 • DRIVER 1 12 3388-91310 • WRENCH ...

  • RedMax HC510DV - page 42

    The California Air Resources Board and KOMATSU ZENOAH are pleased to explain the emission control system warranty on your 1995 and later small off-road engine. In California, new small off-road engines must be designed, built and equipped to meet the state’s stringent anti-smog standards. KOMATSU ZENOAH must warrant the emission control system on ...

  • RedMax HC510DV - page 43

    EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE UNIT, KOMATSU ZENOAH AMERICA INC. (THE COMPANY), THROUGH ANY RedMax DEALER, WILL REPAIR OR REPLACE, FREE OF CHARGE, FOR THE ORIGINAL AND EACH SUBSEQUENT PURCHASER, ANY PART OR PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP. EMISSION-RELATED PARTS ARE: TH ...

  • RedMax HC510DV - page 44

    Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., par l'intermédiaire de n'importe quel revendeur RedMax, réparera gratuitement ou remplacera gratuitement pour l'acheteur initial et chaque acheteur successif toute(s) pièce(s) se révélant de constitution et/ou de montage défectueux ...

Fabricant RedMax Catégorie Saw

Les documents que nous recevons du fabricant de l'appareilRedMax HC510DV peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques RedMax
- manuels d’utilisations HC510DV
- fiches produit RedMax
- dépliants
- ou étiquettes-énergie RedMax HC510DV
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation RedMax HC510DV.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation RedMax HC510DV, manuels d’entretien, brefs manuels ou manuels de l’utilisateur RedMax HC510DV. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit RedMax HC510DV.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil RedMax HC510DV, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser RedMax HC510DV par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs RedMax HC510DV.

Le manuel d’utilisation complet RedMax, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel RedMax HC510DV - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières RedMax HC510DV, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lRedMax HC510DV qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil RedMax HC510DV - qui devraient nous aider dans les premières étapes lors de l'utilisation RedMax HC510DV
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de RedMax HC510DV
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service RedMax HC510DV dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de RedMax HC510DV?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec RedMax HC510DV, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec RedMax HC510DV il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)