Français dropdown-ico

Manuel d’utilisation Graco 288217

38 pages 1.5 mb
Télécharger

Aller à la page of 38

Summary
  • Graco 288217 - page 1

    Instr uctions - P ar ts A utomatic XT Spra y Guns 311051F ENG Airspra y , HVLP , and Compliant guns f or spraying paints and coatings. See page 3 f or model inf or mation. 100 psi (0.7 MP a, 7 bar) Maximum W orking Fluid Pressure 100 psi (0.7 M P a, 7 bar) Maximum Working A ir Pressure Important Safety Instru ctions Read all warnings and instr u ct ...

  • Graco 288217 - page 2

    Related Manua ls 2 311051F Contents Related M anuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 W arnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Selection Char ts . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Proper Nee ...

  • Graco 288217 - page 3

    Models 311051F 3 Models * Hardened SST needle tip/nozzle (n ot recommended f or thin fluids). All other models hav e PEEK needle tip . A manif old is required for ea ch gun to be installed. Ref er to the Pa r t s section for m anifold information. Orifice Size in. (mm) HVLP Compliant Airs pray .030 (0.7 5) 249388 249407 249369 .042 (1.0) 249389 249 ...

  • Graco 288217 - page 4

    Warnings 4 311051F Wa r n i n g s The f ollowing wa r nings are for t he setup, use , grounding, maintenan c e, and repair of this equipment. The e xclama- tion point symbol alerts you to a gener al warning and the hazard symbol ref ers to procedure -specific risk. Refer bac k to these wa r nings. Additional, product- specific warnings ma y be fou ...

  • Graco 288217 - page 5

    Warnings 311051F 5 T O XIC FLUID OR FUMES HAZARD T oxic fluid s or fumes can cause serious injur y or death if splashed in the e yes or on skin, inhaled, or s wallowed. • Read MSDS’ s to know the specific hazards of the fluid s you are using. • Store hazard ous fluid in approv ed containers , and dispose of it according to app licable guideli ...

  • Graco 288217 - page 6

    Selection Charts 6 311051F Selection Char ts TERMS: Light Fluid: Up to 18 seco nds with No. 2 Zahn cup (20 centipoise) Medium Fluid:19 to 28 seconds with No . 2 Zahn cup (20-64 centipoise) Heav y Fluid:Greater than 28 se conds with No . 2 Zahn cup (gre ater than 64 centipoise) -- 2.8 V olatile Organic Compounds, High-solid P oly uretha nes, Heavy W ...

  • Graco 288217 - page 7

    Selection Charts 311051F 7 Compliant Spra y Gun Assemblies * Hardened SST needle tip/nozzle (n ot recommended f or thin fluids). All other models hav e PEEK needle tip . † With Fluid Control Knob (f or fine adjustmen t of fluid flow). Airspra y Gun Assemblies * Hardened SST needle tip/nozzle (n ot recommended f or thin fluids). All other models h ...

  • Graco 288217 - page 8

    Selection Charts 8 311051F Pr oper Needle/Nozzle Selection The spra y gun's needle/nozzle kits range in size to pro- vide different fluid flow r ate s. As a general guideline, use th e fluid nozzle that will give the required flo w with the needle fully triggered at a fluid pressure of 5-20 psi (0.035 MP a, 3.5 bar - 0.14 MP a. 14 bar) F or lo ...

  • Graco 288217 - page 9

    Air Flow 311051F 9 Air Flo w All tests were completed with the 0.055 in. (1 .4 mm) nozzle and stand ard air cap for each gu n model. F IG . 1: HVLP Gun Air Cap Pres sure F IG . 2: A utomatic Gun Air Consumption HV LP Ai rcap Pressures 0 1 2 3 4 5 6 7 8 9 10 11 12 0 5 10 15 20 25 30 35 40 45 50 Manif old Inlet Pr e s s ur e p si Ai rcap P r essur e ...

  • Graco 288217 - page 10

    Installation 10 311051F Installation The A utomatic XT spra y guns were designed to pr oduce the highest quality finish with toda y's fluids as well as the low V .O .C . (volatile orga nic compound) fluids of tomorrow . This spra y gun can spra y most coat ings or finishes cur- rently being used f or automotiv e, industrial, aerospace, marine, ...

  • Graco 288217 - page 11

    Installation 311051F 11 Install Air Fittings 1. Install the sup plied 1/4 in. tube fitting into the cylin - der (CYL) air port. 2. Install 3/8 in. tu be fittings into the atomization (A T OM) air por t and the f an (F AN) air por t. Gr ound System The f ollowing groundin g instr uctions are minimum requirements f or a system. Y our system may inclu ...

  • Graco 288217 - page 12

    Installation 12 311051F Mount Gun Reciprocating Arm Rod Mount T o mount the gun on a reciprocating arm rod [0.5 i n. (13 mm) diameter maxim um]: 1. Insert the mounting bar (A) thr ough the hole in the manif old as shown in F IG . 5. 2. Secure the gun to the bar b y tightening th e mount- ing screw (B). Stationary Suppor t T o mount the gun on a sta ...

  • Graco 288217 - page 13

    Setup 311051F 13 Setup Connect Air Line 1. F or manif olds with a separate A T OM and F AN por t, the gun cylinder , fan, an d atomization air must be supplied and regulate d separately . F or the manual f an valv e manifo ld, only one supply line is required f or both atomization an d fan air . 2. Connect each air hose (D) to a regulate d air supp ...

  • Graco 288217 - page 14

    Setup 14 311051F Flush Spra y Gun Bef ore running any paint through the sp ray gu n: 1. Flush the gun with a solv ent that is compatib le with the fluid to be sp ray ed, using the lo west possib le fluid pressure and a g rounded metal container . 2. P erform Pressure Relief Procedure ; see page 17. P osition Air Cap Air caps are factor y-set with t ...

  • Graco 288217 - page 15

    Setup 311051F 15 Adjust Spra y P attern The spra y gun fluid flo w is controlled by the fl uid pres- sure regulator and t he fluid control knob . Use the fluid pressure regula tor to adjust the gene ral fluid flow and the fluid control kn ob to make precise fluid flow adjust- ments . F ollow the se steps to e stablish the correc t fluid flow and ai ...

  • Graco 288217 - page 16

    Setup 16 311051F 3. T est the spra y pattern atomization while keeping the gun a consistent distance , about 6 to 8 inches (150 to 200 mm), from the te st piece. Check the atomizatio n quality . Increase the gun atomizing air supply pr essure with the air pressure regulator in 5 psi (34 kP a, 0.3 bar) increments unt il yo u obtain the desired atomi ...

  • Graco 288217 - page 17

    Operation 311051F 17 Operation Pressure Relief Pr ocedure 1. T ur n off all b leed type air v alves and all other air and fluid supplies to th e gun. 2. T rigger the gun into a groun ded metal waste con- tainer to relie ve air and fluid pr essure. Appl y Fluid The spra y gun has a b uilt-in lead and lag oper ation. When trig gered, the gun be gins ...

  • Graco 288217 - page 18

    Daily Gun Care 18 311051F Dail y Gun Care CA UTION Meth ylene chloride with f or mic or propionic acid is not recommended as a flushing or cleaning solv ent with this gun as it will damage aluminum and nylon compo- nents . CAUTION Solv ent left in gun air passages could result in a poor qua lity paint finish. Do not use any cleaning method which ma ...

  • Graco 288217 - page 19

    Daily Gun Care 311051F 19 General System Maintenance •P e r f o r m Pressure Relief Pr ocedure , page 1 7. • Clean the fluid and air line f ilters daily . • Chec k for an y fluid leakage from the gun an d fluid hoses. Tighten fittings or replace equip ment as needed. • Flush the gun bef ore changing colors and whene ver yo u are done operat ...

  • Graco 288217 - page 20

    Troubleshooting 20 311051F T r oubleshooting General T roub leshooting Check all possib le remedies in the troubleshoot ing char ts bef ore disassembling th e gun. Some improper patte r ns are caused by th e improper balance be tween air and fluid. Ref er to Spray Pattern T roubleshoo ting , page 22. Prob lem Cause Solution Fluid leakage throu gh v ...

  • Graco 288217 - page 21

    Troubleshooting 311051F 21 Fluid needle will not trigger . Loos e or missing fluid needle stop (29) or setscrew (30). Air leaking around piston (3). Swollen piston o-ring (8). Insufficient air pressure on trigger . Plug (19) is in incorr ect fluid por t. Replace stop or tight en setscrew . Replace o-ring (8) or pi ston. Replace o-ring. Do not immer ...

  • Graco 288217 - page 22

    Troubleshooting 22 311051F Spra y P attern T roub leshooting Prob lem Cause Solution Fluid flow is flutter ing while spraying. Fluid nozzle is not tight eno ugh. O-ring (36) is missing or damaged. Fluid filter is clogged. Tighten flui d nozzle to 60 in-lb (6.8 N•m). Replace o-ring. Check fluid filter . Fluid flo w fades while spr aying high visco ...

  • Graco 288217 - page 23

    Service 311051F 23 Service Items Needed f or Service • 1/16 in. He x Wrench - prov ided •3 m m H e x W r e n c h • Adjustab le Wrench •4 m m H e x W r e n c h • Pliers • Lubricant par t no . 111265; see Acce ssories , page 33, to order • Compatib le Solvent Replace Fluid P ac kings and Air Seals 1. P erform Pressure Re lief Procedure ...

  • Graco 288217 - page 24

    Service 24 311051F 13. Remove all o-r ings from th e piston (3) a nd stems (T). Chec k that the stems are solidly in place . If they are loose, replac e the entire piston asse mbly (3). 14. P erf or m the f ollowing applicab le step: a. Non-circulating guns: Remo ve th e fluid outlet por t plug (19) , and gask et (22) from the flu id housing (2). R ...

  • Graco 288217 - page 25

    Service 311051F 25 Reassembl y 1. Non-circulating guns only: L ubr icate the backup ring (20†) and o-ring (21†) and install them on th e fluid outlet por t plug (19). Insta ll the plug in the fluid out- let por t of the fluid housing (2). See F IG . 22. 2. All guns: Reinstall the gasket (22) in the flu id hous- ing (2). 3. Install the o- r ings ...

  • Graco 288217 - page 26

    Parts 26 311051F Pa r t s F IG . 22 SERVICE NOTES: Torque to 35-45 in-lb (4.0-5.1 N•m) Lubricate threads with anti-seize lubricant Lubricate with light-weight oil Tighten cap (4) until it bottoms out Apply semi-permanen t anaerobic sealant Torque to 4-5 in-lb (0.45-0.57 N•m) Torque to 95-105 in-lb (10.7-1 1.8 N•m) Apply semi-p ermanent anaero ...

  • Graco 288217 - page 27

    Parts 311051F 27 Pa r t s ★ See spra y gun assemb lies table (pag e 28) for part number . † Included in Flu id Seal Repair Kit 288135. * Included in Air Seal Re pair Kit 288171. ❄ Not shown. Air Caps Ref. No. P a rt No . Description Qty . 1B O D Y 1 2 15H321 HOUSING, flui d 1 3 240895 PIST ON, assy 1 4 CAP , piston 1 192453 standard mode ls 2 ...

  • Graco 288217 - page 28

    Parts 28 311051F Spray Gun Assemb l ies (all models) * Guns with stainless steel needle tip , which is not rec- ommended f or th in fluids. † Guns with Fluid Control Knob . Needle Tips Gun P art No. Needle/Nozzle Kit Includes items 5 & 23 Item 5 Needle Assy . Includes item 5a Item 5a Needle Tip Pa c k o f 5 Item 23 Nozzle Item 24 Nozzle Orifi ...

  • Graco 288217 - page 29

    Parts 311051F 29 P ar t No. 288221 Manif old with bottom fl uid por ts ❄ Not shown. Ref. No. P a rt No . Description Qty . 101 MANIFOLD , bottom fluid por ts 1 103 120388 FITTING, tube, air inlet; 1/4 in. OD tube x 1/8 npt(m) 1 105 114246 SCREW , set; 5/16;0.437 in. long 1 107 166846 NIPPLE, SST; 1/4 npsm, straight pipe thre ad x 1/4 np t 2 108 1 ...

  • Graco 288217 - page 30

    Parts 30 311051F P ar t No. 288217 Nor th America Manifold with side fluid ports P ar t No. 288218 International Manif old with side fluid por ts ❄ Not shown. ❖ P ar t No . 288217 only . ◆ P ar t No . 288218 only . Ref. No. P a rt No. Descri ption Qty . 101 MANIFOLD , side fluid po r ts 1 103 1 120388 ❖ FITTING, tube, air inlet; 1/4 in. OD ...

  • Graco 288217 - page 31

    Parts 311051F 31 P ar t No. 288223 Low Pressure Manif old with side fluid ports and fan adjustment valve ❄ Not shown. Ref. No. P art No. Descri ption Qty . 101 MANIFOLD , f an adjustab le 1 102 243949 V AL VE, f an, assy . 1 103 120388 FITTING, tube , air inlet; 1/4 in. OD tube x 1/8 npt( m) 1 104 120389 FITTING, tube , air line; 3/8 in.OD tube x ...

  • Graco 288217 - page 32

    Parts 32 311051F P ar t No. 288160 Rear P or t Manifold, Nor th Amer ica P ar t No. 288211 Rear P or t Manifold, International ❖ P ar t No . 288160 only . ◆ P ar t No . 288211 only . Ref. No. P art No. Descriptio n Qty . 101 MANIFOLD , aluminum 1 103 FITTING, fluid path 2 15H521 ❖ 1/4 npsm 15J003 ◆ #5 JIC 105 116475 SCREW , SHCS, M4 x 12 2 ...

  • Graco 288217 - page 33

    Accessories 311051F 33 Accessories Cleaning Brush 105749 F or use in cleaning gun. Lubricant 111265 One 4 oz. (113 gram) tube sa nitary (non-silicone) lubr i- cant f or fluid seals a nd wear areas . Fluid Hose P ar ts Breakdown Alternate Nozzle Sizes Retrofit Adapter Plate 288197 The retrofit adapter plat e enables the manif old to be attached to a ...

  • Graco 288217 - page 34

    Dimensions 34 311051F Dimensions F IG . 28 TI8181a TI8104a 2.0 in. (50.8 mm) 5.3 in. (134.6 mm) Part No. 249407 Gun Shown 3.86 in. (98 .0 m) 3.0 in. (76.2 mm) 1.395 in. (35.43 mm) 2.76 in. (70.1 mm) 6.41 in. (162.81 mm) with fluid control knob 0.5 in. (12.7 mm) mounting hole ...

  • Graco 288217 - page 35

    Mounting Hole Layout 311051F 35 Mounting Hole La y out F IG . 29: Manif old Mounting Hole La yout TI8107a TI8181a 0.4 in. (10.2 mm) Two M5 x 0.8 x 0.25 in. (6.3 mm) holes 0.805 in. ( 20.5 mm) 0.187 in. (4.8 mm) 1.375 in. (35 mm) 1.750 in. (44.5 mm) Two 0.128 diame ter x 0.31 in. (7.8 mm) h oles 2.125 in. (54 mm) Use 1/8 in. pin for alignment 2.02 i ...

  • Graco 288217 - page 36

    Mounting Hole Layout 36 311051F Mounting Hole La y out F IG . 30: Mounting Hole La youts TI8177a Rear Port Manifold Retrofit Adapter Plate Gun with Retrofit Adapter Plate TI8178a 2.007 i n. (50.98 mm) 1.375 i n. (34.93 mm) 0.736 in. (18.69 mm) TI8226a 2.27 in. (57.66 mm) Rear Port Ma nifold TI8232a 2.325 in. (59.06 mm) 1.765 i n. (44.83 mm) 3.730 i ...

  • Graco 288217 - page 37

    Technical Data 311051F 37 Te c h n i c a l D a t a Loctite ® is a registere d trademark of th e Loctite Cor poration. T riggering Speed These v alues apply to a new gun with a 12 f t. (3.6 m), 1/4 in. (6.3 mm) OD cylinder air line and a 0.055 in. nozzle. These v a lues will vary slightly with use and with variations in equipment. Sound Data (dBa) ...

  • Graco 288217 - page 38

    All written and visual data contained in this document reflects the latest product information available at the time of publica tion. Graco reserves the right to make changes a t any time without notice. This manual contains English. MM 311051 Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Korea GRACO INC. P.O. BOX 14 ...

Fabricant Graco Catégorie Paint Sprayer

Les documents que nous recevons du fabricant de l'appareilGraco 288217 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Graco
- manuels d’utilisations 288217
- fiches produit Graco
- dépliants
- ou étiquettes-énergie Graco 288217
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Graco 288217.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Graco 288217, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Graco 288217. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Graco 288217.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Graco 288217, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Graco 288217 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Graco 288217.

Le manuel d’utilisation complet Graco, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Graco 288217 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Graco 288217, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lGraco 288217 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Graco 288217 - qui devraient nous aider dans les premières étapes lors de l'utilisation Graco 288217
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Graco 288217
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Graco 288217 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Graco 288217?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Graco 288217, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Graco 288217 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)