Français dropdown-ico

Manuel d’utilisation Extron electronic SCP 226

60 pages 4.74 mb
Télécharger

Aller à la page of 60

Summary
  • Extron electronic SCP 226 - page 1

    68-959-01 Rev. F 07 12 System Control Panels SCP 226 and SCP 104 Series User Guide ...

  • Extron electronic SCP 226 - page 2

    Pr ecautions This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock. Caution Read Inst ...

  • Extron electronic SCP 226 - page 3

    安全须知 • 中文 这个符号提示用户该设备用户手册中 有重要的操作和维护说明。 这个符号警告用户该设备机壳内有暴 露的危险电压，有触电危险。 注意 阅读说明书 • 用户使用该设备前必须阅读并理 解所有安全和使用说明。 保存说明书 • 用户应保存安全说明 ...

  • Extron electronic SCP 226 - page 4

    Conventions Used in this Guide Notifications the following are used: WARNING: Risk of physical injury . A warning indicates a situation that has the potential to result in death or severe injury . A TTENTION: Attention indicates a situation that may damage or destroy the product or associated equipment. NOTE: A note draws attention to important inf ...

  • Extron electronic SCP 226 - page 5

    Contents Introduction .......................................1 About this Guide ................................ 1 About the SCP 104 and SCP 226 System Control Panels ...................... 1 Features .......................................... 2 Application Diagrams ........................ 3 Installation and Operation ............. 5 UL Requiremen ...

  • Extron electronic SCP 226 - page 6

    SCP 104 and SCP 226 • Contents vi ...

  • Extron electronic SCP 226 - page 7

    Intr oduction This section gives an overview of the SCP 104 and SCP 226 System Control Panels and describes their features. T opics include: • About this Guide • About the SCP 104/226 Series System Control Panels • Application Diagrams About this Guide This guide discusses how to install, connect, and operate the Extron SCP 104 and SCP 226 Sy ...

  • Extron electronic SCP 226 - page 8

    The MediaLink controllers and the System 5 IP each support up to two of the SCP 104/226, the SCP 226 L, or the SCP 104/226 AAP models. The MLC 104/226 and the System 5 IP can each support up to four control modules and one IR Link infrared signal repeater , which can be daisy-chained with the panels. The SCP 226 models can accept signals from the o ...

  • Extron electronic SCP 226 - page 9

    Application Diagrams The following illustrations show examples of how the SCP can be connected. 100-240V 0.2A 50-60Hz + _ LEFT + RIGHT _ B A S C 4 C 3 C C 1 2 B A E C D 5 6 Tx Rx G G Ps +V S G G S G S G R Y G Y B V H VID VID VID VID C Y C Y R/VID G/Y B/C H V C VID V H R/VID G/Y B/C INPUT 1 INPUT 2 AMPLIFIE D OUT CM/IR/SCP RELAYS RS-232 2 3 4 PROJ C ...

  • Extron electronic SCP 226 - page 10

    3 1 2 OUTPUT INPUTS MLS 103 V L R A B L R L R L R 1 2 3 L R 4 AU X/ MI X MO NO AUDIO INPUTS OUT CONTROL/ POWER 12V .5A MAX BASS LEVEL TREBLE MINI POWER AMPLIFIER MPA 152 STEREO DUAL MONO CONFIG DISPLAY MLC 104 IP VOLUME 1 2 3 4 ON OFF CONFIG DISPLAY SCP 104 IP VOLUME 1 2 3 4 ON OFF VIDEO AUX VIDEO PC IMAGE MUTE VIDEO AUX VIDEO PC IMAGE MUTE Ext ron ...

  • Extron electronic SCP 226 - page 11

    Installation and Operation This section describes the front and rear panel features of the six SCP 104/226 models and provides procedures for installing and operating the control panels. T opics that are covered include: • UL Requirements • Installation Overview • Installing or Replacing Button Labels • Rear Panel Features and Connections ? ...

  • Extron electronic SCP 226 - page 12

    Installation Overview A TTENTION: Installation and service must be performed by authorized personnel only . T o install and set up an SCP control panel: 1. Power off all equipment. Make sure that the SCP and all attached devices are disconnected from the power sources. 2. Set the panel address DIP switch on the back of the SCP (see a "Panel ad ...

  • Extron electronic SCP 226 - page 13

    Fig_Replacing button label 2 3 TEXT Separate the two- piece button here at the corner. Pry the two pieces apart. Diffuser Plunger Base Button Label Clear Cap Notch Figure 3. Replacing a Button Label 4. Lift out the transparent square label that you want to replace, being careful not to damage the circuits beneath it. Y ou may need to use the small ...

  • Extron electronic SCP 226 - page 14

    Rear Panel Features and Connections 1 ON 2 3 4 J1 1 2 4 A B C D E A B C D E Figure 4. SCP 104 Rear Panel 1 ON 2 3 4 J1 1 3 4 A B C D E A B C D E 2 Figure 5. SCP 226 Rear Panel a Panel address DIP switches — Set these DIP switches as appropriate for your system configuration. • Switch 1 — Switches the SCP between connected and standalone mode ...

  • Extron electronic SCP 226 - page 15

    NOTE: The SCP must be in standalone mode for communication via SIS commands (see the “ Remote Communication ” section, beginning on page 31). • Switch 2 — Sets the addresses for the SCPs when two are connected. Ensure that this switch is set to opposite positions on the two SCPs. For example: • If switch 2 is set to Off (down) on the fir ...

  • Extron electronic SCP 226 - page 16

    d Serial port — Use this female 3-pole 3.5 mm captive screw connector to connect the SCP to the serial (RS-232) port on your computer . Through this connection you can enter SIS commands to monitor and obtain information from the SCP (see " Wiring the RS-232 Port " for connection information). Wiring the RS-232 Port The RS-232 port prov ...

  • Extron electronic SCP 226 - page 17

    1 ON 23 4 J1 J4 J6 SW12 SCP 226 Rotated Rear P anel To Computer or Control System RS-232 Po rt 9-pin HD Connector Ground Receive Tr ansmit Tx 3 Tr ansmit (Tx) Receive (Rx) 2 Ground (G) 5 Rx G Figure 7. Connecting a Host to the SCP 226 2. Plug the 3-pole connector into the RS-232 port on the SCP rear panel. NOTES: • DIP switch #1 must be set to On ...

  • Extron electronic SCP 226 - page 18

    Wiring the Power Connector (Optional) If powering the SCP using a 12 V , 1 A external power supply (instead of powering via an MLC or System 5 IP), connect the power supply to ports A and B of either 5-pole captive screw connector on the SCP rear panel. Connect the + wire to port A and the ground wire to port B, as shown in the figures below . SEC ...

  • Extron electronic SCP 226 - page 19

    Connecting to the MLC 104/226, the System 5 IP , and Control Modules The diagrams on the following pages illustrate how to connect the SCP to the MLC 104, MLC 226, control modules such as IRCMs or RCMs, and the System 5 IP system switcher . NOTES: • When an SCP 104 is connected to an MLC 104 IP Plus, the SCP must have firmware version 1.01 or hig ...

  • Extron electronic SCP 226 - page 20

    SCP 226 to MLC 226 IP SCP 226 200' (61 m) max. to Last Device E B A SCP Communication +12 VDC Ground ( ) & Drain Wire MLC 226 IP Rear Panel Extron CTLP Cable Color Code: Ground ( ) & Drain Wire E D C B A SCP Communication Modulated IR (for IR Link) Control Module Communication +12 VDC = White = Black & Drain Wire = Red VO LUME SCP ...

  • Extron electronic SCP 226 - page 21

    SCP 226 to MLC 226 IP with IRCM-DV+ control modules SCP 226 3-pole Connector SCP 226 3-pole Connector C B A C B A Extron CTLP Cable Color Code: 200' (61 m) max. to Last Device IRCM-D V+ Control Module Address 1 and 2 IRCM-D V+ Control Module Address 1 and 2 IRCM-D V+ Control Module Address 1 and 2 NOTE: Use a different DIP switch 2 setting for ...

  • Extron electronic SCP 226 - page 22

    SCP to system switcher SCP 104 Extron CTLP Cable Color Code: 200' (61 m) max. to Last Device IRCM-D V+ Control Module Address 1 and 2 E C B A SCP Communication IRCM, AC M, RCM +12 VDC Ground ( ) & Drain Wire Ground ( ) & Drain Wire E D C B A SCP Communication Modulated IR (for IR Link) Control Module Communication +12 VDC = White = Bla ...

  • Extron electronic SCP 226 - page 23

    T wo SCP 226s to system switcher and two control modules Figure 15. Connecting T wo SCP 26 Control Panels to a System Switcher and T wo Control Modules SCP 226 SCP 226 C B A C B A E E C B A E Extron CTLP Cable Color Code: 200' (61 m) max. to Last Device IRCM-D V+ Control Module Address 1 and 2 IRCM-D V+ Control Module Address 3 and 4 E C B A S ...

  • Extron electronic SCP 226 - page 24

    SCP and System 5 IP Button Functions When an SCP is connected to a System 5 IP switcher , buttons on the SCP initiate functions that are also controlled by equivalent buttons on the switcher . The following diagrams show the buttons on the SCP that are tied to buttons on the System 5 IP . SCP 104 System 5 IP CONFIG DISPL AY VO LUME SCP 104 ON PC DO ...

  • Extron electronic SCP 226 - page 25

    Mounting the SCP After the system has been cabled and tested, the control panel can be mounted to the wall or furniture. Mounting Options Y ou can mount the SCP 104/226 in an electrical box or surface mounting box (not provided), or you can use a mounting bracket (not provided) to secure it to a wall, podium, table, or other furniture. Extron offer ...

  • Extron electronic SCP 226 - page 26

    Fig_Mounting SCP 104_2-gang 2-gang Wa ll Box Extron SCP 104 C O N F IG PROJECT OR VOL UM E 1 2 3 4 O N OFF Figure 18. Mounting an SCP 104 in a T wo-gang Electrical Box A TTENTION: If you are not installing the SCP into a grounded metal electrical box, make sure that the faceplate is grounded to an earth ground. Mounting to a Lectern (SCP 226 L) The ...

  • Extron electronic SCP 226 - page 27

    Front Panel Featur es The controls on the SCP 104/226 replicate the programmed MLC 104/226 buttons and controls, and most of the System 5 IP front panel controls. All button functions for the MLCs and the System 5 IP are configured via RS-232 or Ethernet. Any action taken at the SCP front panel, such as turning the knob to increase or decrease vol ...

  • Extron electronic SCP 226 - page 28

    SCP 104 PROJECT OR V OLUME ON OFF 1 2 3 4 1 3 6 7 7 7 7 Figure 20. SCP 104 Front Panel SCP 104 AAP 4 3 6 1 7 7 7 7 Figure 21. SCP 104 AAP Front Panel SCP 104 and SCP 226 • Installation and Operation 22 ...

  • Extron electronic SCP 226 - page 29

    Figure 22. SCP 226 Front Panel Figure 23. SCP 226 AAP Front Panel V OLUME SCP 226 IR PROJECT OR Extron 1 2 3 4 5 6 ON OFF 1 3 2 6 7 7 7 7 5 Extron PROJECT OR 1 2 3 4 5 6 V OLUME IR ON OFF 1 3 6 2 4 5 SCP 226 AAP 7 7 7 7 7 7 SCP 104 and SCP 226 • Installation and Operation 23 ...

  • Extron electronic SCP 226 - page 30

    Extron PROJECT OR 1 2 3 4 5 6 V OLUME IR ON OFF SCP 226 2 7 3 7 7 7 1 5 6 Figure 24. SCP 226 L Front Panel a On and Off buttons — Press these buttons to turn the projector or display on and off. The buttons flash while the display device is warming up or cooling down, then light steadily . b and c : Function/Input buttons — These sets of butto ...

  • Extron electronic SCP 226 - page 31

    d AAP mounting spaces (SCP AAP models only) — Mount up to four single space AAPs or control modules (IRCMs or RCMs) here. e IR signal pickup sensor (SCP 226 models only) — This sensor allows control of the SCP 226 using an optional Extron IR 402 remote control. Point the remote directly at the sensor . The remote has a range of approximately 30 ...

  • Extron electronic SCP 226 - page 32

    f V olume knob and indicator LEDs — T urn this knob to adjust the volume on the input that is currently selected. The five LEDs light incrementally , bottom to top, to indicate the current volume level, as shown in figure 26 . The top LED is red; the others are green. VOLUME VOLUME VOLUME VOLUME LED Off LED Blinking LED On 0% (Min) or Mute 1-19 ...

  • Extron electronic SCP 226 - page 33

    V OLUME SCP 226 IR PROJECT OR Extron 1 2 3 4 5 6 ON OFF To reset, press these bu ttons simultaneously while applying po we r. Figure 28. Resetting the SCP 226 to Factory Defaults Updating the Firmware If necessary , you can replace the firmware on the SCP without changing firmware chips. This procedure must be performed using a computer on which ...

  • Extron electronic SCP 226 - page 34

    3. On the Download Center screen, click Software on the left sidebar menu. The Download Center Control Software screen appears. 4. On the software list, scroll to locate Firmware Loader and click on the Download link at right. Figure 29. Download Link for Firmware Loader 5. On the next download screen, fill in the required information, then click ...

  • Extron electronic SCP 226 - page 35

    8. Start the Firmware Loader program by clicking the Firmware Loader icon on your computer Start menu. The Firmware Loader Add Device screen appears. Figure 31. Firmware Loader Add Device Scr een 9. From the four drop-down menus, select the following: • Device Name : SCP 104 or SCP 226 • Connection Method : RS-232 • Com Port : Select the Com ...

  • Extron electronic SCP 226 - page 36

    Figure 33. Open Window for Firmware 12. In the Open window , locate and double-click on the firmware filename (it has a .bin extension). NOTE: The firmware update file must have a filename extension of .bin . If the file does not have that extension, the unit does not function properly . The path to the firmware file is displayed in the Pat ...

  • Extron electronic SCP 226 - page 37

    Remote Communication This section discusses use of SIS commands via RS-232 communication to monitor and get information from the SCP . It contains lists and explanations of the SIS commands that are available for the SCP . T opics that are covered include: • Setting Up RS-232 Communication • Communications Between the Host and the SCP • Using ...

  • Extron electronic SCP 226 - page 38

    SCP-initiated Messages At power-up, the following SCP-initiated message appears: (c) Copyright 20 nn , Extron Electronics, SCP 104 [or 226], V n . nn NOTE: This message is displayed only at power-up. When a local event such as a front panel selection takes place, the SCP 104/226 responds by sending a message to the host indicating what selection wa ...

  • Extron electronic SCP 226 - page 39

    Using the Command and Response T ables The command and response tables on the following pages list valid command ASCII codes, the SCP responses to the host, and a description of the command function or the results of executing the command. The ASCII to hexadecimal conversion table below is for use with the command and response tables. ASCII to Hex ...

  • Extron electronic SCP 226 - page 40

    Command ASCII Command (Host to SCP) Hex (Host to SCP) Response (SCP to Host) Additional Description Information Requests Query firmware version q 71 X! ] Show current firmware version X! . Query firmware version — factory and updated 0q 30 71 x.xx , y.yyy ] x . xx = factory firmware version number format. y . yyy = updated firmware version n ...

  • Extron electronic SCP 226 - page 41

    Command ASCII Command (Host to SCP) Hex (Host to SCP) Response (SCP to Host) Additional Description Information Requests (continued) Request control module and connected modules (for 3-pole connection only) 32i 33 32 69 P1 nn • K1 nn • K2 nn • K3 nn • K4 nn • ] P1 nn = SCP address K1 nn = control module 1; address 00 K2 nn = control modul ...

  • Extron electronic SCP 226 - page 42

    Command ASCII Command (Host to SCP) Hex (Host to SCP) Response (SCP to Host) Additional Description Upload Firmware Upload firmware E Upload } Go ] Upl ] When you receive the Go response, upload the firmware according to the procedure for your terminal emulator . When the upload is complete, you receive the Upl ] response. Reset to Default Settin ...

  • Extron electronic SCP 226 - page 43

    Special Function SIS Commands The syntax for setting a special function for an SCP 104/226 is X? * Y? * __ # , where X? is the value of the action to be performed, Y? is the value for the button or switch, and __ is the function number . T o view the setting of a function, use __# , where __ is the function number . In the following tables the valu ...

  • Extron electronic SCP 226 - page 44

    Command ASCII Command (Host to SCP) Response (SCP to Host) X? and Y? V alues and Additional Descriptions Switch Responses Button press on front panel or remote control (none) SwPrs * X? ] X? = Switch number for the function. There are 128 options available (1-128; see the Switch and Button T able on page 44 for these values). Button release on fron ...

  • Extron electronic SCP 226 - page 45

    Command ASCII Command (Host to SCP) Response (SCP to Host) X? and Y? V alues and Additional Descriptions Front Panel Button LED Contr ol FPC lamp control X? * Y? * 51# Lmp Y? * X? ] X? = LED state: Y? = Button: 0 = all LEDs off 0 = no button 1 = green LED on 1 = projector on 2 = red LED on 2 = projector off 3 = green and red 3 = function 1 LEDs on ...

  • Extron electronic SCP 226 - page 46

    Using the Switch and Button T able Switches are assigned to specific buttons on the SCP , any attached remote control module (IRCM or RCM), or the IR 402 remote. Each time a button is pressed or released, or a knob is turned on the SCP or a control module, the switch number associated with that button appears on the screen of your PC terminal emul ...

  • Extron electronic SCP 226 - page 47

    Front panel switch locations V OLUME SCP 226 IR PROJECT OR Extron 1 2 3 4 5 6 ON OFF 1 2 5 9 10 11 12 13 14 6 7 Figure 35. Switch Locations on the SCP 226 Fig_Switch locations SCP 104 SCP 104 PROJECT OR V OLUME ON OFF 1 9 10 11 12 2 Figure 36. Switch Locations on the SCP 104 41 SCP 104 and SCP 226 • Remote Communication ...

  • Extron electronic SCP 226 - page 48

    IR 402 switch locations 2 1 4 121 123 7 3 6 5 111 109 125 110 116 118 24 120 122 124 113 112 114 119 117 115 25 108 IR 402 See the SCP 104/226 front panel. 9-22 Figure 37. Switch Numbering for the IR 402 Remote Control Control modules switch locations Each control module (IRCM or RCM) has 20 switches reserved for it, no matter how many buttons are ...

  • Extron electronic SCP 226 - page 49

    uFig_Button and Switch numbering SCREEN POSITION DOWN UP STOP DV D & VCR CONTROL PLA YN EXT/FW DP AU SE STOP TUNER Tx PREV/REW ENTER TITLE MENU TV/VCR DV DV CR DV D & VCR CONTROL PLA YN EXT/FW DP AU SE STOP TUNER Tx PREV/REW ENTER TITLE MENU TV/VCR DV DV CR Button/Switch Numbering Scheme fo r Any T ype of Module (Example is for Control Modu ...

  • Extron electronic SCP 226 - page 50

    Switch and Button T able Switch Button Switch Button Switch Button CM3_2 CM3_3 CM3_4 CM3_5 CM3_6 CM3_7 CM3_8 CM3_9 CM3_10 CM3_11 CM3_12 CM3_13 CM3_14 CM3_15 CM3_16 CM3_17 CM3_18 CM3_19 CM3_20 Not av ailable Not av ailable Audio mute Arrow up Arrow down Arrow left Arrow right Title Enter − DV D Stop − DV D Play − DV D P ause − DV D Previous ...

  • Extron electronic SCP 226 - page 51

    Refer ence Information This section contains reference information for all SCP 104 and SCP 226 models. T opics include: • Part Numbers • Cutout T emplates Part Numbers The following tables show the part numbers for the SCP 104 and SCP 226 models and for the equipment and accessories that are used with the SCP . Models The SCP 104 and SCP 226 ar ...

  • Extron electronic SCP 226 - page 52

    Recommended Cables Cable T ypes Part Numbers CTLP/1000 Plenum 1000' (300 m) spool 22-119-03 CTL/1000 Non-Plenum 1000 ' (300 m) spool 22-148-03 Accessories Check the Extron website ( www .extron.com ) for available accessories. Mounting Options Part Numbers Mounting brackets (mud rings): MR 200 2-gang (black or white) 70-519-22, -23 MR 300 ...

  • Extron electronic SCP 226 - page 53

    Cutout T emplates This section contains the following cutout templates: • SCP 104 Cutout T emplate • SCP 104 AAP Cutout T emplate • SCP 226 Cutout T emplate • SCP 226 AAP Cutout T emplate • SCP 226 L Cutout T emplate NOTE: These templates are not to scale and are provided for reference only . SCP 104 Cutout T emplate SCP 104 Cut-Out T emp ...

  • Extron electronic SCP 226 - page 54

    SCP 104 AAP Cutout T emplate SCP 104 AAP Cut-Out T emplate for Extron's TEMPLA TE IS NO T FULL SIZE. 4.50" (11.43 cm) To install SCP 104 directly into furniture, cut along this line. 8.33" (21.16 cm) 2.83" (7.2 cm) SURF ACE CUT -OUT AREA FOR FURNITURE MOUNT 7.26" (18.44 cm) T op P anel Location of SCP 104 1.45" (3.68 c ...

  • Extron electronic SCP 226 - page 55

    SCP 226 Cutout T emplate To install SCP 226 directl y into furniture, cut along this lin e. To p Pa nel 2.81" (7.13 cm) 5.24" (13.3 cm) SURF ACE CUT -OUT AREA FOR FURNITURE MOUNT Location of SCP 226 SCP 226 Cut-Out T emplate for Extron's TEMPLA TE IS NOT FULL SIZE. 4.50" (11.43 cm) 6.40" (16.3 cm) 1.39" (3.53 cm) 0.61& ...

  • Extron electronic SCP 226 - page 56

    SCP 226 AAP Cutout T emplate 10.13" (25.65 cm) SCP 226 AAP Cut-Out T emplate for Extron's TEMPLA TE IS NO T FULL SIZE. 4.50" (11.43 cm) To install SCP 226 directly into furniture , cut along this line. T op P anel Location of SCP 226 8.72" (22.15 cm) 2.81" (7.13 cm) SURF ACE CUT -OUT AREA FOR FURNITURE MOUNT 1.45" (3.6 ...

  • Extron electronic SCP 226 - page 57

    SCP 226 L Cutout T emplate SCP 226 L Cut-Out T emplate for Extron's 6.50" (16.51 cm) TEMPLA TE IS NOT FULL SIZE. To install SCP 226 directly into furniture , cut along this line. T op Panel 3.15" (8.00 cm) Location of SCP 226 2.81" (7.13 cm) 5.24" (13.30 cm) SURF A CE CUT -OUT AREA FOR FURNITURE MOUNT 0.25" (0.64 cm) 0 ...

  • Extron electronic SCP 226 - page 58

    52 SCP 104 and SCP 226 • Reference Information ...

  • Extron electronic SCP 226 - page 59

    W arranty Extron W arranty Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extron Electronics will, at its option, repair or replace said pr ...

  • Extron electronic SCP 226 - page 60

    Extron USA Headquarters +800.633.9876 (Inside USA/Canada Only) Extron USA - West Extron U SA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 FAX +1.919.850.1001 FAX Extron Europe +800.3987.6673 (Inside E urope O nly) +31.33.453.4040 +31.33.453.4050 FAX Extron India 1800.3070.3777 (Inside India Only) +91-80 3055.3777 +91 80 3055 3737 FAX Extr ...

Fabricant Extron electronic Catégorie Stereo System

Les documents que nous recevons du fabricant de l'appareilExtron electronic SCP 226 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Extron electronic
- manuels d’utilisations SCP 226
- fiches produit Extron electronic
- dépliants
- ou étiquettes-énergie Extron electronic SCP 226
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Extron electronic SCP 226.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Extron electronic SCP 226, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Extron electronic SCP 226. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Extron electronic SCP 226.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Extron electronic SCP 226, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Extron electronic SCP 226 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Extron electronic SCP 226.

Le manuel d’utilisation complet Extron electronic, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Extron electronic SCP 226 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Extron electronic SCP 226, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lExtron electronic SCP 226 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Extron electronic SCP 226 - qui devraient nous aider dans les premières étapes lors de l'utilisation Extron electronic SCP 226
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Extron electronic SCP 226
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Extron electronic SCP 226 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Extron electronic SCP 226?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Extron electronic SCP 226, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Extron electronic SCP 226 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)