Français dropdown-ico

Manuel d’utilisation OTC Wireless ASR-102

29 pages 0.74 mb
Télécharger

Aller à la page of 29

Summary
  • OTC Wireless ASR-102 - page 1

    i WiFi Wireless Ethernet Adapter AirEZY-2411-BT (ASR-102/ACR-201) User Guide ...

  • OTC Wireless ASR-102 - page 2

    ii AirEZY 2411 BT (ASR-102/ACR-201) Wireless Ethernet Adapter User’s Manual Copyright Information in this document is subjec t to change without not ice. Complying wit h all applicable copyright laws is the res ponsibility of the user. No part of this document may be reproduced or transmitt ed in any form or by any means, electronic or mechanical ...

  • OTC Wireless ASR-102 - page 3

    iii Table of Contents AirEZY-2411-BT (ASR-102/ACR-201) User’s Manual Chapter 1 INTRODUCTION 1 Data Sheet 2 Chapter 2 INSTALLATION 3 Installing the Hardware 3 Power 3 Ethernet connection 3 Status LEDs 3 Optional Hardware 5 Installing the Utility Software 6 System Requirement 6 Installation 6 Chapter 3 UTILITY SOFTWARE 7 Use the Utility Program 7 O ...

  • OTC Wireless ASR-102 - page 4

    1 Chapter 1 INTRODUCTION AirEZY-2411-BT is an 802. 11b compliant, or WiFi, radio with a 10-BaseT interface. Two features separate AirEZY- 2411-BT from many other 802.11b-compliant radios. Firstly, this 802.11b-compliant (WiFi) radio can be configured as either a Station (ACR-201) or an AP (ASR-102). Secondly, when configured as a Station, the 10-Ba ...

  • OTC Wireless ASR-102 - page 5

    2 AirEZY-2411-BT (ASR- 102/ACR-201) WiFi Radio Specifications Model AirEZY-24 11-BT Standard 802.11 and 802 .11b Host Interf ace Ethernet, 802.3, RJ-45 receptacle Frequency 2.4GHz – 2.49 5GHz RF Channels 11 channels ( US, Canada), 13 channels (Europe), 13 channels (Ja pan) Transmission power 14dBm at antenna in put typica l Receiver sensitivity - ...

  • OTC Wireless ASR-102 - page 6

    3 Chapter 2 INSTALLATION Installing the Hardware Power This radio is capable of pulling power from either an AC adapter (supplied with the standard purchase) that plugs into a wa ll outlet or from the USB or the PS2 port of a notebook computer through special adapter cables (call OTC to find out more about these optional cables), or through a batte ...

  • OTC Wireless ASR-102 - page 7

    4 in the shipment. Power on the AirEZY 2411 BT, the LEDs on the front panel should exhibit the following patterns: LED Color Light Blinking Pattern ON RED Steady on RX GREEN Steady on TX RED on, when transmitting RF signal LINK YELLOW Flickering when comm unicating over the Ethernet port; steady-on when Ethernet connection is absent If the yellow L ...

  • OTC Wireless ASR-102 - page 8

    5 Three installation examples are shown below. Optional Hardware Radio with externally mount ed antenna (ASR-102E/ACR-201E) Power over Ethernet: DC-injector and dc-extractor 9V adapter if up to 120-ft long CAT-5 cable is used 12V adapter if up to 240-ft long CAT-5 cable is used USB power cable PS2 power cable Power drawn from the USB Ethernet Adapt ...

  • OTC Wireless ASR-102 - page 9

    6 Installing the Utility Software System Requirements To use the AirEZY-2411-BT Wireless Ethernet Adapter’s utilit ies software, your computer must meet the follo wing minimum requirements: Windows® 95 (OSR2)/ 98 (SEC)/ME/2000/XP Ethernet capable computer with RJ-45 port (either built-i n or add-on NIC) Installation To install the utility pr ogr ...

  • OTC Wireless ASR-102 - page 10

    7 Chapter 3 UTILITY SOFTWARE Use the Utility Program Once the radio is properly turned on an d connected either directly to the computer running t he Utility program or to a port on the same subnet, the Utility is ready for use. To start the Utility program from your Microsoft Windows, click “Start”, then “P rogram”, move to locate the “A ...

  • OTC Wireless ASR-102 - page 11

    8 Configure AirEZY-2411-BT as an Access Point (ASR-102) By checking the “Change Role to AP” (r ed-arrowed in screen-shot #3), most parameter fields become undimmed and modifiable, as se en in screen-shot #3 . With the exception of the “MAC” field, and sometimes the “Allowed Station List” field, each filed can be m odified and uploaded i ...

  • OTC Wireless ASR-102 - page 12

    9 Each field on this “Access Point” sub-tab is explained below. Device Name: Allows the user to enter a use r- defined name for the radio. Up to 32 bytes can be used. MAC: Displays the MAC address of the radio when it is configured as an AP. This filed cannot be modified. SSID: Service Set Identity is used by a station radio when issuing Associ ...

  • OTC Wireless ASR-102 - page 13

    10 exactly the same SSID as the SSID entered in this sub-tab. The tightest level of network access control is implemented in Level 3, [Hide SSID, Match SSID, Use Allowed List] , add one additional criterion for a Station to gain access to the network associated with this AP—it s MAC address m ust appear in the “ Allowed Station List ” (see be ...

  • OTC Wireless ASR-102 - page 14

    11 system” mode. When the “shared key” option is chosen, the “Encryption” tab of the Utility program must be properly filled out. Fragmentation Threshold: In the presence of hostile RF environment, such as interference, frames longer than this thre shold numbers in bytes are divided prior to transmission into one or more fragm ents equal ...

  • OTC Wireless ASR-102 - page 15

    12 Configure AirEZY-2411-BT as a Station (ACR-201) Click on the “Station” sub-tab to display the “Station” page if the “Access Point” page is on top after clicking the “Configuration” tab. Similar to the case of configuring the radio for AP, checking the “Change Role to Station” undims the page and makes most fields modifiable. ...

  • OTC Wireless ASR-102 - page 16

    13 PS Mode: Power Saving can be enabled only w hen “Infrastructure” is select ed for the “Network Type”. Channel: This field is modifiable only when the “Ad hoc” type is selected for “Network Type”. The Station automatically scans for the right channel to join when operated in the “Infrastructure” m ode. In the “Ad hoc” mode ...

  • OTC Wireless ASR-102 - page 17

    14 applied to other Wi-Fi radios, however, may re sult in very different keys. For this reason, clicking the Apply button after entering the pass-phrase will caus e the 4 sets of keys being temporarily displayed under “Manual Entry” as if they were entered manually. (See screen-shots #9 and #10, the display in screen-shot #10 is dimmed and not ...

  • OTC Wireless ASR-102 - page 18

    15 of the default keys for transmitting its data. When Use Dynamic WEP Key is checked, only 3 default keys are available for selection (Screen Shot #11). Note that once the Dynamic WEP Key is in force, the Transmission Key Selection (Screen Shot#12) made by the user is only used in the authentication process and is irrelevant in the encryption of t ...

  • OTC Wireless ASR-102 - page 19

    16 transmitted data packets. “Signal Strength” directly measures the amount of RF energy received relative to a “maximum” expected for the best condition. The two measures are related, but could differ due to various reasons. In general, as a first step toward maximizing Link Quality, one should try to maximize the Signal Strength by moving ...

  • OTC Wireless ASR-102 - page 20

    17 Notice also that in this manual mode th roughputs in Bits/Sec are not calculated due the imprecise timing. Uninstall the Utility Software If you need to uninstall the Utility softwar e for any reason, complete the following steps: 1. Close all programs that are currently running. 2. Click the Window Start button, point to Settings and then click ...

  • OTC Wireless ASR-102 - page 21

    18 Chapter 4 TROUBLESHOOTING Blank Pages Appear When Open the Utility Program This is either because the radio is extr emely busy on the RF side or because the Ethernet connection is problematic. Try to hit the Refresh button a few times. If the blank-page condition persists, it is unlik ely that t he problem is caused by a busy radio. Check your E ...

  • OTC Wireless ASR-102 - page 22

    19 • Make sure that the MAC address of the Station in question is properly entered into the “Allowed Station List” of the AP if enhanced security level 3, [Hide SSID, Match SSID, Use Allowed List] , is chosen. • Make sure that the Station in ques tion has exactly the same SSID as the AP if enhanced security level 2 or 3 is chosen. • Make ...

  • OTC Wireless ASR-102 - page 23

    20 • Make sure that the radio is not surrounded by many strongly reflecting (metallic) surfaces. With multiple refl ecting surfaces between the radio in question and the target radio, a severe “ multi-path ” problem may introduce high bit error rate despite a strong “Signal Strength”. • Make sure that there is not a condition of severe ...

  • OTC Wireless ASR-102 - page 24

    21 Appendix A: LIMITED WARRANTY Wireless LAN Hardware The seller warrants to the end user (“Cus tomer”) that this hardware product will be free from defects in workmanship and materials, under normal use and service, for one (1) year from the dat e of purchase from the seller or its authorized reseller. The seller’s sole obli gation under thi ...

  • OTC Wireless ASR-102 - page 25

    22 Appendix B: REGULATORY COMPLIANCE FCC Part 15 Declaration of Conformity (DoC) The following equipment: Product Name: Wireless Ethernet Adapter Model Number: AirEZY-2411-BT WLAN is herewith confirmed to comply with the requirements of FCC Part 15 rules. The operation is subject to the following two conditions: 1. This device may not cause harmful ...

  • OTC Wireless ASR-102 - page 26

    23 European Community (EC) Directi ves Conformity and Restrictions This product is in conformity with the protection requirements of EC Council directives 89/336/EEC, 73/23/EEC, and 1 999/5/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed fo ...

  • OTC Wireless ASR-102 - page 27

    24 GLOSSARY 10BaseT An IEEE standard (802.3) for operat ing 10 Mbps Ethernet networks (LANs) with twisted pair cabling and a wiring hub. Access Point An internetworking device that seamlessly connects wired and wireless networks. Access Points combin ed with a distributed system support the creation of multiple radio cells t hat enable roaming thro ...

  • OTC Wireless ASR-102 - page 28

    25 Hidden Node The situation where two or more radios in a multiple-radio network fail to detect the RF signals from each other. For example, in a 3-radio network, radio 2 and 3 both have good link to ra dio 1. Radio 2 and 3, however, are isolated from each other by, say, a meta l wall. Radio 2 therefore is a “hidden node” to radio 3, and vice ...

  • OTC Wireless ASR-102 - page 29

    26 PCMCIA Personal Computer Memory Card International Association . Th is Association develops standards for PC card s, formerly known as PCMCIA cards. These cards are available in three ty pes, and are about the same length and width as credit cards. However, the diffe rent cards range in thickness from 3.3 mm (Type I) to 5.0 mm (Type II) to 10. 5 ...

Fabricant OTC Wireless Catégorie Network Card

Les documents que nous recevons du fabricant de l'appareilOTC Wireless ASR-102 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques OTC Wireless
- manuels d’utilisations ASR-102
- fiches produit OTC Wireless
- dépliants
- ou étiquettes-énergie OTC Wireless ASR-102
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation OTC Wireless ASR-102.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation OTC Wireless ASR-102, manuels d’entretien, brefs manuels ou manuels de l’utilisateur OTC Wireless ASR-102. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit OTC Wireless ASR-102.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil OTC Wireless ASR-102, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser OTC Wireless ASR-102 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs OTC Wireless ASR-102.

Le manuel d’utilisation complet OTC Wireless, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel OTC Wireless ASR-102 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières OTC Wireless ASR-102, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lOTC Wireless ASR-102 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil OTC Wireless ASR-102 - qui devraient nous aider dans les premières étapes lors de l'utilisation OTC Wireless ASR-102
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de OTC Wireless ASR-102
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service OTC Wireless ASR-102 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de OTC Wireless ASR-102?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec OTC Wireless ASR-102, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec OTC Wireless ASR-102 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)