Français dropdown-ico

Manuel d’utilisation Chamberlain SW470

40 pages 3.18 mb
Télécharger

Aller à la page of 40

Summary
  • Chamberlain SW470 - page 1

    C O N TRO LLER BO ARD GL MODELS SW470 AND SW490 ARE FOR VEHICULAR PASSAGE GATES ONLY AND NOT INTENDED FOR PEDESTRIAN PASSAGE GATE USE. MODEL SW4 70 MEDIUM DUT Y SWING GA TE OPERA TOR Serial # _______________________ (located on electrical box cover) Installation Date _________________ 2 YEAR WARRANTY MODEL SW490 HEA V Y DUT Y SWING GA TE OPERA TOR ...

  • Chamberlain SW470 - page 2

    2 2 OPERATOR SPECIFICATIONS Carton Inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Operator Dimensions and Specifications . . . . . . . . . . . . . . . . . . . 3 UL325 Model Classifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 OPERATOR WARNINGS Suggested Safety Protection Device Locations ...

  • Chamberlain SW470 - page 3

    3 3 OPERATOR DIMENSIONS AND SPECIFICATIONS MODEL SW470 • 1/2 HP Motor Maximum Gate Weight – 500 lbs. (226.8 kg) Maximum Gate Width – 12 ft. (3.7 m) MODEL SW490 • 1/2 HP Motor Maximum Gate Weight – 750 lbs. (340.2 kg) Maximum Gate Width – 16 ft. (4.9 m) • 3/4 HP Motor Maximum Gate Weight – 900 lbs. (408.2 kg) Maximum Gate Width – 1 ...

  • Chamberlain SW470 - page 4

    4 4 The SW470 and SW490 are intended for use with vehicular swing gates. The opener can be used in Class I, Class II, Class III and Class IV applications. SAFETY ACCESSORY SELECTION All UL325 compliant LiftMaster gate operators will accept external entrapment protection devices to protect people from motorized gate systems. UL325 requires that the ...

  • Chamberlain SW470 - page 5

    5 5 * REFER TO LOOP MANUFACTURER’S INSTRUCTIONS FOR DETAILED INSTALLATION & LOOP WIRING INSTRUCTIONS. DUAL SWING GATE SYSTEM SWING GATE SYSTEM SUGGESTED SAFETY PROTECTION DEVICE LOCATIONS Telephone Entry System STREET Interrupt (Safety) Loop Interrupt (Safety) Loop Shadow Loop Photo eye for close cycle 4' (1.2 m) Typical Photo eye for op ...

  • Chamberlain SW470 - page 6

    6 6 1. Vehicular gate systems provide convenience and security. Gate systems are comprised of many component parts. The gate operator is only one component. Each gate system is specifically designed for an individual application. 2. Gate operating system designers, installers and users must take into account the possible hazards associated with eac ...

  • Chamberlain SW470 - page 7

    7 1.1 Gates shall be constructed in accordance with the provisions given for the appropriate gate type listed, refer to ASTM F2200 for additional gate types. 1.2 Gates shall be designed, constructed and installed to not fall over more than 45 degrees from the vertical plane, when a gate is detached from the supporting hardware. 1.3 Gates shall have ...

  • Chamberlain SW470 - page 8

    8 8 Moving Gate Can Cause Injury or Death KEEP CLEAR! Gate may move at any time without prior warning. Do not let children operate the gate or play in the gate area. This entrance is for vehicles only Pedestrians must use separate entrance WARNING SIGN PLACEMENT SAFETY PRECAUTIONS FOR SWING AND ORNAMENTAL "GRILL TYPE GATES" To prevent SER ...

  • Chamberlain SW470 - page 9

    9 INSTALLATION POST MOUNTING (SW470) 1. Locate and anchor two posts made of 3 " (7.6 cm) outer diameter heavy walled pipe. Posts should be parallel and square to the gate. IMPORTANT NOTE: The distance between mounting posts and the relative location of the operator to the gate and fence is critical. 2. Locate electrical conduit, as required, p ...

  • Chamberlain SW470 - page 10

    10 c 8" 8" 6" Operator 24" 22-1/2" 9-3/4" Concrete pad 18"x34" min. 1/2" Redhead (4 required.) Fence Hinge Pin Parallel Mount Centerline Gate 8"16"1/2" Redhead (4 required) SW470 Perpendicular Profile of Operator Concrete pad 18"x34" min. 18-3/4" Perpendicular Mount 22-1/2&q ...

  • Chamberlain SW470 - page 11

    11 11 PAD MOUNTING (SW490) 1. Measure the gate length and select appropriate “P” dimension from the gate installation table. 2. Layout the concrete pad as detailed in Figure 1. IMPORTANT NOTE: The relative location of the operator to the fence and the gate is critical. Be sure that the measurements for operator mounting are taken from the cente ...

  • Chamberlain SW470 - page 12

    12 CONTROL ARM ASSEMBLY (SW470) 1. Set the control arm stop on the operator in the positions appropriate for the installation (Figure 1). 2. Install the arm channel to the hub assembly to the operator output shaft. 3. Secure the arm channel to arm hub with 1/4-20 black plastic knobs provided (Hub is factory installed - Figure 2). 4. Assemble extens ...

  • Chamberlain SW470 - page 13

    13 13 INST ALL A TION CONTROL ARM ASSEMBLY (SW490) 1. Set the control arm’s close stop on the operator so that its position corresponds with the handling of the installation (Figure 1). 2. Remove the open stop, as it is not to be used in this application. Use any existing hardware necessary to seal the open stop’s hole in the operator’s cover ...

  • Chamberlain SW470 - page 14

    14 14 INST ALL A TION CONTROL ARM ASSEMBLY (SW490) continued MANUAL DISCONNECT MODEL SW470 1. Remove the (2) black knobs securing the control arm to the operator (Figure 1). 2. Swing arm assembly off to the side. Gate should swing freely. MODEL SW490 1. Remove hitch pin and pivot pin securing control arm to arm assembly (Figure 2). 2. Swing arm ass ...

  • Chamberlain SW470 - page 15

    15 15 NOTE: Calculated using NEC guidelines. Local codes and conditions must be reviewed for suitability of wire installation. All power wiring should be dedicated and protected. Location of primary power disconnect should be labeled. WIRING To reduce the risk of SEVERE INJURY or DEATH: • ANY maintenance to the operator or in the area near the op ...

  • Chamberlain SW470 - page 16

    16 16 ON/OFF SWITCH POWER WIRING NOTE: Before running power wiring refer to wiring specifications on page 15 for correct wire gauges. Secure all electrical power connections inside the disconnect switch electrical box. Refer to electrical wiring diagrams on pages 31-33. IMPORTANT: On three phase operators, power connections must be properly phased. ...

  • Chamberlain SW470 - page 17

    17 PROGRAMMING THE RADIO RECEIVER SET SECURITY MODE The Universal Receiver can be used with up to 15 315 MHz rolling code remote controls or PINs in HIGH security mode. Alternately, it can be used with up to 31 of any type 315 MHz remote control in NORMAL security mode, including any combination of rolling code, billion code, or dip switch remotes. ...

  • Chamberlain SW470 - page 18

    18 Limit Switch “B” Limit Switch “A” Aux switch (optional) Drive Shaft Set Screw 18 LIMIT SWITCH ADJUSTMENT NOTE: For limit location and configuration refer to Figure 1. 1. Before turning on power, disconnect extension arm from gate bracket so gate is no longer connected to operator. Push manual release pin(s) up through the control arm, sl ...

  • Chamberlain SW470 - page 19

    19 19 RPM SENSOR (HALL EFFECT) ADJUSTMENT NOTE: Normally the RPM sensor (hall effect) does not need adjustment, but may go out of alignment due to shipping vibration or rough handling. These operators use an internal entrapment protector system. This system consists of the control board, magnet, and RPM sensor. It may become necessary to adjust the ...

  • Chamberlain SW470 - page 20

    20 20 The Sequenced Access Management System or SAMS allows the customer more control when managing vehicular entrances to areas such as apartment complexes, businesses and gated communities. The basic concept of the system is that traffic is controlled by two gates installed in tandem, a fast moving gate such as a barrier gate operator and a slowe ...

  • Chamberlain SW470 - page 21

    21 SOFT OPEN 1 2 3 4 5 6 7 8 9 10 INTERRUPT (SAFETY) LOOP INPUT 5 8 9 10 1 1 12 21 ACCESSORY WIRING All inputs are normally open and momentary, except the stop (N.C.). The following instructions are based upon UL325, and include recommendations for significant increase in safety. We strongly recommend that you follow the UL guidelines presented thr ...

  • Chamberlain SW470 - page 22

    OP E N CL O SE ST O P OP E N CL O SE ST O P O P E N CL O SE ST O P 22 ACCESSORY WIRING Field Wiring Terminals 9 & 5 - Obstruction Open (Edge/Photo Eye Input) Edge Input: See Programming Section This input will reverse an opening gate to the close limit. Activating this input when the gate is closing will have no effect. NOTE: If upon reversal a ...

  • Chamberlain SW470 - page 23

    23 CONTROL BOARD ILLUSTRA TION Relay Drive Troubleshooting LEDs J1 Terminal Troubleshooting LEDs J5 Connector SAMS J2 Connector J3 Connector Aux. Relay Drive (not used) Motor Learn Button Programming Port (factory use only) Limit LEDs Main Terminal Wiring Potentiometer Timer-to-Close Dip Switch #4 Master/Second J4 Connector Master/Second Diagnostic ...

  • Chamberlain SW470 - page 24

    24 CONTROL BOARD PROGRAMMING AND FEATURES MOTOR LEARN FUNCTION (FORCE PROFILE) This function is preprogrammed at factory. If either board or motor is replaced, the controller will need to be programmed to “LEARN” the specific motor RPM profile of your operator. Switch “S3” is provided for this. This is important for accurate force control. ...

  • Chamberlain SW470 - page 25

    25 LED LED NAME DESCRIPTION RELAY DRIVE TROUBLESHOOTING LEDS There are 5 troubleshooting LEDs on relay drives K1 through K5. These LEDs will be illuminated when the microcontroller relay drive is activated. D6 Contactor A On when Contactor A is activated D5 Contactor B On when Contactor B is activated D4 SAM On when SAM relay is activated D3 Lock O ...

  • Chamberlain SW470 - page 26

    26 Min = 0 sec Max = 180 sec TIMER-TO-CLOSE ENABLE This switch enables the auto close timer. The timer to close feature works in conjunction with the potentiometer located on the board. SLIDE/SWING This switch selects slide or swing gate operation, in order to optimize gate behavior for specific application. SL = Slide • SW = Swing RIGHT/LEFT OPE ...

  • Chamberlain SW470 - page 27

    Master or Standalone Gate Setting 27 PROGRAM SETTINGS (DIP SWITCH S2) EDGE/PHOTO OPEN This switch (S2-3) selects edge or photo sensor for the gate opening protection input. Open Photo Eye (Pause): When the controller is configured for photo eyes, the input functions to pause the gate during the opening cycle. Once the input is cleared the gate cont ...

  • Chamberlain SW470 - page 28

    Operator fails to run. No Stop Control. Check the green LED (D17) on control board. If the green LED is off, check to make sure a stop control has been installed across terminals J1-3 & J1-5 of the control board. Fault in the operator. Check the yellow diagnostic LED at the top right of the control board next to the programming dip switches. If ...

  • Chamberlain SW470 - page 29

    Master or Second operator is not functioning properly. Failure to cycle power after setup. The power to each unit must be cycled in order to initiate proper master/second communication if the operators were previously in stand-alone mode. The communication wiring may be damaged or improperly wired for dual gate operation. Make sure that the communi ...

  • Chamberlain SW470 - page 30

    30 OPERA TOR MAINTENANCE NOTES 1. Severe or high cycle usage will require more frequent maintenance checks. 2. Inspection and service should always be performed anytime a malfunction is observed or suspected. 3. Limit switches may have to be reset after any major drive chain adjustments. 4 If lubricating chain, use only a proper chain lube spray or ...

  • Chamberlain SW470 - page 31

    31 SINGLE PHASE WIRING DIAGRAM (SW4 70) DRA WING NUMBER: 01-G1978 D A TE: 7/29/03 REVISION: E ECN: 03-0401 NO TES: 1) TRANSFORMER PRIMARY V OL T AGE SAME AS OPERA T OR LINE V OL T AGE 24V SECOND ARY 60V A. 2) TERMINAL DESIGNA TIONS SHOWN FOR 115V ONL Y . 3) OPTIONAL WIRE HARNESS. 4) (B+) AND (B-) ARE 100dB SAFETY ALARMS. APPLICA TIONS: CONTROL WIRI ...

  • Chamberlain SW470 - page 32

    32 SINGLE PHASE WIRING DIAGRAM (SW490) DRA WING NUMBER: 01-G1979-1 D A TE: 7/29/03 REVISION: E ECN: 03-0401 NO TES: 1) TRANSFORMER PRIMARY V OL T AGE SAME AS OPERA T OR LINE V OL T AGE 24V SECOND ARY 60V A. 2) RELA Y V OL T AGE SAME AS LINE VOL T AGE. 3) OPTIONAL WIRE HARNESS. 4) (B+) AND (B-) ARE 100dB SAFETY ALARMS. 5) WIRE COLOR: 120V BLA CK, 20 ...

  • Chamberlain SW470 - page 33

    33 THREE PHASE WIRING DIAGRAM (SW490) DRA WING NUMBER: 01-G1979-3 D A TE: 7/29/03 REVISION: E ECN: 03-0401 NO TES: 1) TRANSFORMER PRIMARY V OL T AGE SAME AS OPERA T OR LINE V OL T AGE 24V SECOND ARY 60V A. 2) WIRE COLOR: 208V RED , 230V ORANGE, 460V VIOLET , 575V GRA Y 3) OPTIONAL WIRE HARNESS (SEE DRAWING 90-G0532). 4) O VERLOAD PRO TECTION EITHER ...

  • Chamberlain SW470 - page 34

    34 CONTROL CONNECTION DIAGRAMS 1234567 89 1 0 1 1 1 2 1 3 1 4 1 5 1 6 R2 R1 R4 R3 3 6 9 # 2 5 8 0 1 7 OPEN CLO SE ST OP OPEN CLO SE ST OP OPEN CL O SE ST OP FR EQ FR EQ NOTE: See wiring diagrams shipped with kit for additional information. See owner’s manual for wiring distances and wire gauge information. WARNING: All controls that are to be use ...

  • Chamberlain SW470 - page 35

    35 Refer to the parts lists below for replacement parts available for your operator. If optional modifications and/or accessories are included with your operator, certain components may be added or removed from these lists. Individual components of each kit may not be available. Please consult a parts and service representative regarding availabili ...

  • Chamberlain SW470 - page 36

    36 ILLUSTRA TED PARTS - SW4 70 A4 A5 A3 A1 A7 A2 D9 D2 D3 D12 D8 D1 A6 1 1 8 6 4 9 13 3 D10 7 5 D6 2 D4 D5 12 11 10 D1 1 D7 14 ...

  • Chamberlain SW470 - page 37

    ITEM PART# DESCRIPTION A1-7 K75-18366 Arm Assembly Kit A1 08-2001 Rod End Fitting A2 10-2011 Gate Bracket A3 70-18618 Extension Arm A4 10-3900 Galvanized Tube 39" OD 1" IDx1.315" A5 12-10172 Sleeve Bearing A6 07-2103 Actuator Arm Stop A7 06-2025-T Actuator Arm Assembly K75-18367 Drive Assembly Kit (Motor Not Included) D1 10-2008 Swit ...

  • Chamberlain SW470 - page 38

    38 ILLUSTRA TED PARTS - SW490 A6 1 2 6 3 7 E3 E2 E1 E4 E5 A4 A2 A1 A5 A5 A3 D12 D1 1 D10 D14 D1 D12 D4 D15 D5 D17 D6 D9 F D8 5 4 D7 D19 D2 D13 D16 D18 D21 D20 D3 A7 8 ...

  • Chamberlain SW470 - page 39

    39 VARIABLE PARTS - SW490 VARIABLE PARTS LIST - SW490 PART PART NO. DESCRIPTION USED ON 20-1050-1T 1PH 1/2HP Base Mnt. 115/230V TEFC SW490-33-11, SW490-33-21, SW490-50-11, SW490-50-21 20-1075-1T 1PH 3/4HP Base Mnt. 115/230V TEFC SW490-75-11, SW490-75-21 20-XXXX 20-1100B-2T 1PH 1HP Base Mnt. 115/230V TEFC SW490-100-11, SW490-100-21 (Motor) 20-3050-1 ...

  • Chamberlain SW470 - page 40

    HOW TO ORDER REP AIR PARTS OUR LARGE SERVICE ORGANIZATION SPANS AMERICA FOR INSTALLATION AND SERVICE INFORMATION, CALL OUR TOLL FREE NUMBER 1-800-528-2806 www.liftmaster.com WHEN ORDERING REPAIR PARTS PLEASE SUPPLY THE FOLLOWING INFORMATION: PART NUMBER DESCRIPTION MODEL NUMBER ADDRESS ORDER TO: THE CHAMBERLAIN GROUP, INC. Technical Support Group 6 ...

Fabricant Chamberlain Catégorie Safety Gate

Les documents que nous recevons du fabricant de l'appareilChamberlain SW470 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Chamberlain
- manuels d’utilisations SW470
- fiches produit Chamberlain
- dépliants
- ou étiquettes-énergie Chamberlain SW470
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Chamberlain SW470.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Chamberlain SW470, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Chamberlain SW470. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Chamberlain SW470.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Chamberlain SW470, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Chamberlain SW470 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Chamberlain SW470.

Le manuel d’utilisation complet Chamberlain, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Chamberlain SW470 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Chamberlain SW470, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lChamberlain SW470 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Chamberlain SW470 - qui devraient nous aider dans les premières étapes lors de l'utilisation Chamberlain SW470
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Chamberlain SW470
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Chamberlain SW470 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Chamberlain SW470?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Chamberlain SW470, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Chamberlain SW470 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)