Français dropdown-ico

Manuel d’utilisation Genie NI 5421

36 pages 0.31 mb
Télécharger

Aller à la page of 36

Summary
  • Genie NI 5421 - page 1

    NI 5421 Specifications NI PXI/PCI-5421 16-Bit 100 MS/s Arbitrary Waveform Generator Unless otherwise noted, the followi ng conditions were used for each specification: • Analog Filter enabled. • Interpol ation set to maximum allo wed factor f or a gi v en sample r ate. • Signals terminated with 50 Ω . • Direct Path set to 1 V pk-p k , Lo ...

  • Genie NI 5421 - page 2

    NI 5421 Specifications 2 ni.com CH 0 (Channel 0 Analog Output , Front Panel Connector) Table 1. Specif ication Va l u e Comments Number of Channels 1 — Connector SMB (jack) — Output Voltage Characteristics Output Paths 1. The software-selectable Ma in Output Path setting provides full-scale v oltages from 12.00 V pk-pk to 5.64 mV pk-pk into a 5 ...

  • Genie NI 5421 - page 3

    © National Instruments Corpor ation 3 NI 5421 Specifications Amplitude and Of fset Amplitude Range Pat h Load Amplitude (V pk-pk ) 1. Amp litude values assume the full scale of the D A C is utilized. If an amplitude smaller than the minimu m va lu e i s desired, then wa veforms le ss than full scale of the D A C can be used. 2. NI-F GEN compensate ...

  • Genie NI 5421 - page 4

    NI 5421 Specifications 4 ni.com Maximum Output Voltage Maximum Output Vo l t a g e Pat h Load Maximum Output V oltage (V pk -pk ) The Max imum Output V oltage of the NI 5421 is determined by the Amplitude Range and the Of fset Range. Direct 50 Ω ±0.500 1 k Ω ±0.953 Open ±1.000 Low- Gain Amplif ier 50 Ω ±1.000 1 k Ω ±1.905 Open ±2.000 ...

  • Genie NI 5421 - page 5

    © National Instruments Corpor ation 5 NI 5421 Specifications Output Coupling DC — Output Enable Software-selectable. When disabl ed, CH 0 out is terminated with a 1 W resistor with a value equal to the selected output impedance. — Maximum Output Overload The CH 0 output can be connected to a 50 Ω , ±12 V (±8 V for the Direct Path) s ource ...

  • Genie NI 5421 - page 6

    NI 5421 Specifications 6 ni.com Figure 1. Normalized Pas sband Flatness, Direct Path Figure 2. Pulse Response, Low-Gai n Amplifier Path 50 Ω Load 1.0M 10.0M 48.0M –10.0 –9.0 –6.0 –8.0 –5.0 –7.0 –3.0 –2.0 –1.0 0.0 1.0 2.0 F requency (Hz) dB –4.0 +0.3 dB –0.4 dB –0.4 dB +0.4 dB +0.6 dB –0.4 dB Guaranteed Specification Typi ...

  • Genie NI 5421 - page 7

    © National Instruments Corpor ation 7 NI 5421 Specifications Table 1. (Continued) Specification Va l u e Comments Suggested Maximum Frequencies for Common Funct ions Function Path Disable the Analog Filter and the Digital Interpolation Filter for S quare, Ramp, and T riangle. Direct Lo w-Gain Amplifier High-Gain Amplifier Sine 43 MHz 43 MHz 43 MHz ...

  • Genie NI 5421 - page 8

    NI 5421 Specifications 8 ni.com Spectral Characteristics (Continued) Spurious-Free Dynamic Range (SFDR) with Harmonics Path Amplitude –1 dBFS. Measured from DC to 50 MHz. Also called harmonic distortion. SFDR with harmonics at low amplitudes is limited by a –148 dBm/Hz noise floor . All values are typical and include aliased harmonics. Direct L ...

  • Genie NI 5421 - page 9

    © National Instruments Corpor ation 9 NI 5421 Specifications Spectral Characteristics (Continued) 0 º C to 40 º C T otal Harmonic Distortion (THD) Path Amplitude –1 dBFS. Includes the 2 nd through the 6 th harmonic. Direct Lo w-Gain Amplifier High-Gain Amplifier 20 kHz –77 dBc (typical) –77 dBc (typical) –77 dBc (typical) 1 MHz –75 dBc ...

  • Genie NI 5421 - page 10

    NI 5421 Specification s 10 ni.com A verage Noise Density Pat h Amplitude Range A verage Noise Density A verage Noise Density at small amplitudes is limited by a –148 dBm/Hz noise floor . V pk-pk dBm dBm/Hz dBFS/ Hz Direct 1 4.0 18 –142 –146.0 Lo w Gain 0.06 –20.4 9 –148 –127.6 Lo w Gain 0.1 –16.0 9 –148 –132.0 Lo w Gain 0.4 –4 . ...

  • Genie NI 5421 - page 11

    © National Instruments Corpor ation 11 NI 5421 Specifications Figure 3. 10 MHz Single-T one Spectrum , Direct Path, 100 MS/s, Interpolation Factor S et to 4 Note The noise floor in Figure 3 is lim ited by the measurement de vice. Refer to the Average Noise Density specif ication. 0.0 25.0M 50.0M 75.0M 100.0M 125.0M 158.0M 175.0M 200.0M –90.0 – ...

  • Genie NI 5421 - page 12

    NI 5421 Specification s 12 ni.com Figur e 4. 10 MHz Single-T one Spectrum, Low -Gain Amplifier Path, 100 MS/s, Interpolation Factor Set to 4 Note The noise floor in Figure 4 is lim ited by the measurement de vice. Refer to the Average Noise Density specif ication. 0.0 25.0M 50.0M 75.0M 100.0M 125.0M 150.0M 175.0M 200.0M –90.0 –80.0 –50.0 –7 ...

  • Genie NI 5421 - page 13

    © National Instruments Corpor ation 13 NI 5421 Specifications Figure 5. Direct Path, 2-T one Spectrum (T ypical) Note The noise floor in Figure 5 is lim ited by the measurement de vice. Refer to the Average Noise Density specif ication. 0.0 25.0M 50.0M 75.0M 100.0M 125.0M 150.0M 175.0M 200.0M –90.0 –80.0 –50.0 –70.0 –40.0 –60.0 –30.0 ...

  • Genie NI 5421 - page 14

    NI 5421 Specification s 14 ni.com Sample Clock Table 2. Specif ication Va l u e Comments Sources 1. Internal, Di vide-by- N ( N ≥ 1) 2. Internal, DDS-based, High-Resolution 3. External, CLK IN (SMB front panel connector) 4. External, DDC CLK IN (DIGIT AL D A T A & CONTR OL front panel conn ector) 5. NI PXI-5421 : External, P XI Star trigger ( ...

  • Genie NI 5421 - page 15

    © National Instruments Corpor ation 15 NI 5421 Specifications Effective Sample Rate Sample Rate (MS/s) Interpolation Factor Ef fecti ve Sample Rate Ef fecti ve Sample Rate = (Interpolation Factor) * (Sample Rate) 10 S/s to 105 MS/s 1 (Off) 10 S/s to 105 MS/s 12.5 MS/s to 105 MS/s 2 25 MS/s to 210 MS/s 10 MS/s to 100 MS/s 4 40 MS/s to 400 MS/s 10 M ...

  • Genie NI 5421 - page 16

    NI 5421 Specification s 16 ni.com System Phase Noise and Jitter (10 MHz Carrier) Sample Clock Source System Phase Noise Density (dBc/Hz) Offset System Output Jitter (Integrated from 100 Hz to 100 kHz) 1. High- Resolution specifications increase as the Sample Rate is decreased. 2. NI PXI-5421 PXI Star trigger specification is v alid when the Sample ...

  • Genie NI 5421 - page 17

    © National Instruments Corpor ation 17 NI 5421 Specifications Onboard Clock (Internal VCXO) Sample Clock Exporting Exported Sample Clock Destinations 1. PFI<0..1> (SMB front panel connectors) 2. DDC CLK OUT (DIGIT AL D A T A & CONTR OL front panel connector) 3. NI PXI-5421 —PXI_T rig<0..7> (backplane connecto r) NI PCI-5421 —R ...

  • Genie NI 5421 - page 18

    NI 5421 Specification s 18 ni.com Phase-Locked Loop (PLL) Reference Clock Table 4. Specif ication Va l u e Comments Sources 1. NI PXI-5421 —PXI_CLK10 (backplane connector) NI PCI-5421 —R TSI_7 (R TSI_CLK) 2. CLK IN (SMB fro nt panel connector) The PLL Reference Clock provides the reference frequenc y for the phase-locked loop. Frequenc y Accura ...

  • Genie NI 5421 - page 19

    © National Instruments Corpor ation 19 NI 5421 Specifications CLK IN (Sample Clock and Reference Cloc k Input, Front Panel Connector) Table 5. Specif ication Va l u e Comments Connector SMB (jack) — Direction Input — Destinations 1. Sample Clock 2. PLL Reference Clock — Frequenc y Range 1 MHz to 105 MHz (Sample Clock destination and sine wa ...

  • Genie NI 5421 - page 20

    NI 5421 Specification s 20 ni.com PFI 0 and PFI 1 (Programmable Function Interfac e, Front Panel Connectors) Table 6. Specif ication Va l u e Comments Connectors T wo SMB (jack) — Direction Bi-directional — Frequenc y Range DC to 105 MHz — As an Input (Trigger) Destinations Start T rigger — Maximum Input Overload –2 V to +7 V — V IH 2.0 ...

  • Genie NI 5421 - page 21

    © National Instruments Corpor ation 21 NI 5421 Specifications V OH Minimum: 2.9 V (open load), 1.4 V (50 Ω load) Output driv ers are +3.3 V TTL compatible. Measured with a 1 m cable. V OL Maximum: 0.2 V (open load), 0.2 V (50 Ω load) Rise/F all T ime (20% to 80%) ≤ 2.0 ns Load of 10 pF . Table 6. (Cont inued) Specif ication Va l u e Comments ...

  • Genie NI 5421 - page 22

    NI 5421 Specification s 22 ni.com DIGIT AL DA T A & CONTROL (DDC) Optional Front Panel Connector Table 7. Specif ication Va l u e Comments Connector T ype 68-pin VHDCI female receptacle — Number of Data Output Signals 16 — Control Signals 1. DDC CLK OUT (clock output) 2. DDC CLK IN (clo ck input) 3. PFI 2 (input) 4. PFI 3 (input) 5. PFI 4 ( ...

  • Genie NI 5421 - page 23

    © National Instruments Corpor ation 23 NI 5421 Specifications Output Signal Characteristics (Continued) Output Skew T ypical: 1 ns, maxim um 2 ns. Ske w between any two outp uts on the DIGIT AL DA T A & CONTR OL front panel connector . — Output Enable/Disabl e Controlled through the so ftware on all Data Output Signals and Control Signals co ...

  • Genie NI 5421 - page 24

    NI 5421 Specification s 24 ni.com Start T rigger DDC CLK IN Clocking For ma t DDC Data Output signals change on the rising edge of DDC CLK IN. — Frequenc y Range 10 Hz to 105 MHz — Input Duty Cycle T olerance 40% to 60% — Input Jitter T olerances 300 ps pk-pk of Cycle-Cycle Jitter, and 1 ns rms of Period Jitter . — Table 8. Specif ication V ...

  • Genie NI 5421 - page 25

    © National Instruments Corpor ation 25 NI 5421 Specifications Delay from Start T rigger to CH 0 Analog Output Interpolation Factor T ypical Delay Refer to t s2 at NI Signal Generators Help»Devices» NI 5421» NI <bus>-5421» Triggering» Trigger Timing . Digital Inter polation F ilter disabled. 43 Sample Clock Periods + 110 ns 2 57 Sample C ...

  • Genie NI 5421 - page 26

    NI 5421 Specification s 26 ni.com Markers Table 9. Specif ication Va l u e Comments Destinations 1. PFI<0..1> (SMB front panel connectors) 2. PFI<4..5> (DIGIT AL D A T A & CON TR OL front panel connector) 3. NI PXI-5421 —PXI_T rig<0..6> (backplane connector) NI PCI-5421 —R TSI<0..7> — Quantity One Marker per Se gme ...

  • Genie NI 5421 - page 27

    © National Instruments Corpor ation 27 NI 5421 Specifications W aveform and Instruction Memor y Utilization Table 10. Specif ication Va l u e Comments Memory Usage The NI 5421 uses the Synchronization and Memory Core (SMC) technology in which wav eforms and instructions share onboard memory . Parameters, such as number of segments in sequence list ...

  • Genie NI 5421 - page 28

    NI 5421 Specification s 28 ni.com Loop Count 1 to 16,777,21 5. Burst trigger: Unlimited — Quantum W aveform size must be an integer multiple of four samp les. — Memory Limits 8 MB Standard 32 MB Optio n 256 MB Option All trigger modes except where noted. Arbitrary W av eform Mode, Maximum W av eform Memory 4,194,176 Samples 16,777,088 Samples 1 ...

  • Genie NI 5421 - page 29

    © National Instruments Corpor ation 29 NI 5421 Specifications Calibration Power Table 11. Specif ication Va l u e Comments Self-Calibrati on An onboard, 24-bit ADC and precision voltage reference are used to calibrate the DC gain and offset. The self-calibration is initiated by the user through the software and takes approximately 75 s econds to c ...

  • Genie NI 5421 - page 30

    NI 5421 Specification s 30 ni.com Software Table 13. Specif ication Va l u e Comments Dri ver Software NI-FGEN 2.0 or later ve rsion. NI-FGEN is an IVI-compliant driv er that all o ws you to configure, control, and calibrate the NI 5421. NI -FGEN prov ides application programming interfaces fo r man y de velopment en vironment s. — Application So ...

  • Genie NI 5421 - page 31

    © National Instruments Corpor ation 31 NI 5421 Specifications Environment NI PXI-5421 Environment Note T o ensure that the NI PXI-5421 cools ef fectively , follo w the guidelines in the Maintain Forced-Air Cooling Note to Users incl uded in the NI 542 1 kit. The NI PXI-5421 is intended for indoor use only . Table 14. Specifications Va l u e Comm e ...

  • Genie NI 5421 - page 32

    NI 5421 Specification s 32 ni.com NI PCI-5421 Environment Note T o ensure that the NI PCI-5421 cools ef fectively , follo w the guidelines in the Maintain Forced -Air Cooling Note to Users included in the NI 5421 kit. Also, to maximize airflo w and extend the life of the de vice, lea ve any adjacent PCI slots empty . The NI PCI-5421 is intended for ...

  • Genie NI 5421 - page 33

    © National Instruments Corpor ation 33 NI 5421 Specifications Safety , Electromagnetic Compatibility , and CE Compliance Table 16. Specification Va l u e Comments Safety The NI 5421 is designed to meet th e requireme nts of the following standards of safety for electrical equi pment for measurement, contro l, and laboratory use: IEC 61010-1, EN 6 ...

  • Genie NI 5421 - page 34

    NI 5421 Specification s 34 ni.com Physical Table 17. Specif ication Va l u e Comments Dimensions NI PXI-5421 NI PCI-5421 — 3U, One Slot, PXI/cPCI Module 2.0 × 13.0 × 21.6 cm (0.8 × 5.1 × 8.5 inches) 34.07 × 10.67 × 2.03 cm (13.4 × 4.20 × 0.8 inches) We i g h t 345 g (12.1 oz) 419 g (14 .8 oz) — Front Panel Connectors Label Functio n(s) ...

  • Genie NI 5421 - page 35

    © National Instruments Corpor ation 35 NI 5421 Specifications NI PXI-5421 Only—Front Panel LED Indicators Label Function For more informat ion, refer to the NI Sig nal Generators Help. A CCESS LED The A C CESS LED indicates the status of the PCI b us and the interface from the NI 5421 to the controller . A CTIVE LED The A C TIVE LED indicates th ...

  • Genie NI 5421 - page 36

    National Instruments, NI, ni.com, and LabVIEW are tradem arks of National Instruments Corporation. Refer to t he Terms of Use section on ni.com/legal for mor e information abou t National Instruments trademarks. Other product and compan y names mentioned herein are trademarks or trade names of their respective companie s . For patents covering Nati ...

Fabricant Genie Catégorie Portable Generator

Les documents que nous recevons du fabricant de l'appareilGenie NI 5421 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Genie
- manuels d’utilisations NI 5421
- fiches produit Genie
- dépliants
- ou étiquettes-énergie Genie NI 5421
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Genie NI 5421.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Genie NI 5421, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Genie NI 5421. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Genie NI 5421.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Genie NI 5421, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Genie NI 5421 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Genie NI 5421.

Le manuel d’utilisation complet Genie, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Genie NI 5421 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Genie NI 5421, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lGenie NI 5421 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Genie NI 5421 - qui devraient nous aider dans les premières étapes lors de l'utilisation Genie NI 5421
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Genie NI 5421
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Genie NI 5421 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Genie NI 5421?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Genie NI 5421, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Genie NI 5421 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)