-
Hoshizaki KML-700MWH-M - page 1
Hoshizaki “A Superior Degree of Reliability” www .hoshizaki.com Model KML-700MWH-M Low-Profile Modular Crescent Cuber Hoshizaki America, Inc. Issued: 10-13-2009 I N S T R U C T I O N M A N U A L ™ ...
-
Hoshizaki KML-700MWH-M - page 2
IMPORTANT Only qualied service technicians should install, service, and maintain the icemaker. No installation, service, or maintenance should be undertaken until the technician has thoroughly read this Instruction Manual. Likewise, the owner/manager should not proceed to operate the icemaker until the installer has instructed them on its pr ...
-
Hoshizaki KML-700MWH-M - page 3
3 CONTENTS Important Safety Information ................................................................................................. 4 I. Specications ..................................................................................................................... 5 A. Nameplate Rating ................................................... ...
-
Hoshizaki KML-700MWH-M - page 4
4 Important Safety Information Throughout this manual, notices appear to bring your attention to situations which could result in death, serious injury, or damage to the unit. WARNING Indicates a hazardous situation which could result in death or serious injury. CAUTION Indicates a situation which could result in damage to the unit. IMPORTANT Indic ...
-
Hoshizaki KML-700MWH-M - page 5
5 MOTOR-COMPRESSOR THERMALL Y PROTECTED, NOT INTENDED FOR OUTDOOR USE! Hoshizaki America, Inc. Peachtree City , GA www .hoshizaki.com ICE MAKER WITHOUT STORAGE MEANS 45FE COMPONENT I. Specications A. Nameplate Rating 1. KML-700MWH-M (water-cooled marine) See the nameplate for electrical and refrigeration specications. This nameplate is locate ...
-
Hoshizaki KML-700MWH-M - page 6
6 B. Dimensions/Connections 1. KML-700MWH-M (water-cooled marine) Unit: in. (mm) ...
-
Hoshizaki KML-700MWH-M - page 7
7 II. Installation and Operating Instructions WARNING 1. This icemaker must be installed in accordance with applicable international, national, state, and local regulations. . CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after installation. Make sure that none have fallen into the dispenser unit/storage ...
-
Hoshizaki KML-700MWH-M - page 8
8 C. Location CAUTION 1. This icemaker is not intended for outdoor use. Normal operating ambient temperature should be within 45°F to 100°F (7°C to 38°C); Normal operating water temperature should be within 45°F to 90°F (7°C to 3°C). Operation of the icemaker, for extended periods, outside of these normal temperature ranges may affect ic ...
-
Hoshizaki KML-700MWH-M - page 9
9 E. Electrical Connection WARNING 1. Electrical connection must be hard-wired and must meet international, national, state, and local electrical code requirements. Failure to meet these code requirements could result in death, electric shock, serious injury, re, or severe damage to equipment. . This unit requires an independent power supply. ...
-
Hoshizaki KML-700MWH-M - page 10
10 F. Water Supply and Drain Connections See Fig. 4 or 5 WARNING 1. Water supply and drain connections must be installed in accordance with applicable international, national, state, and local regulations. . Normal operating water temperature should be within 45°F to 90°F (7°C to 3°C). Operation of the icemaker, for extended periods, outs ...
-
Hoshizaki KML-700MWH-M - page 11
11 Fig. 4 KML-700MWH-M Connection to an Open Drain System 2. Water-Cooled Condenser a) Connection to an Open Drain System • Condenser water supply inlet is 1/" female pipe thread (FPT). A minimum of 3/8" OD copper tubing is recommended for the condenser water supply line. • A condenser water supply line shut-off valve and drain val ...
-
Hoshizaki KML-700MWH-M - page 12
1 Condenser Return Line Shut-Off Valve Condenser Return Line Drain Valve Icemaker Drain Outlet 3/4" FPT Icemaker Water Supply Inlet 1/" FPT Fig. 5 Condenser Water Supply Inlet 1/" FPT Condenser Return Outlet 3/8" FPT Separate piping to approved drain. Leave a -inch (5-cm) vertical air gap between the end of each pipe ...
-
Hoshizaki KML-700MWH-M - page 13
13 G. Final Checklist WARNING CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after installation. Make sure that none have fallen into the dispenser unit/storage bin. 1) Is the icemaker level? ) Is the icemaker in a site where the ambient temperature is within 45°F to 100°F (7°C to 38°C) and the water ...
-
Hoshizaki KML-700MWH-M - page 14
14 H. Startup WARNING 1. All parts are factory-adjusted. Improper adjustments may adversely affect safety, performance, component life, and warranty coverage. . If the icemaker is turned off, wait for at least 3 minutes before restarting the icemaker to prevent damage to the compressor. 3. To prevent damage to the water pump, do not leave the co ...
-
Hoshizaki KML-700MWH-M - page 15
15 III. Cleaning and Maintenance WARNING CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after any cleaning or maintenance is done to the unit. Make sure that none have fallen into the dispenser unit/storage bin. A. Cleaning and Sanitizing Instructions Hoshizaki recommends cleaning and sanitizing this unit at ...
-
Hoshizaki KML-700MWH-M - page 16
16 8) In bad or severe water conditions, clean the oat switch assembly as described below. Otherwise, continue to step 9. a. Remove the 3 screws securing the oat switch assembly, then remove the assembly. b. Remove the retainer rod from the bottom of the oat switch housing, then remove the oat. Be careful not to bend the retainer rod ex ...
-
Hoshizaki KML-700MWH-M - page 17
17 2. Sanitizing Procedure - Following Cleaning Procedure 1) Dilute 1.5 . oz. (37 ml or .5 tbs) of a 5.5% sodium hypochlorite solution (chlorine bleach) with .5 gal. (9.5 l) of warm water. ) Remove the front insulation panel. 3) Pour the sanitizing solution into the water tank. 4) Move the service switch to the "WASH" po ...
-
Hoshizaki KML-700MWH-M - page 18
18 C. Preparing the Icemaker for Long Storage CAUTION 1. When storing the icemaker for an extended time or in sub-freezing temperatures, follow the instructions below to prevent damage. . To prevent damage to the water pump, do not leave the control switch in the "SERVICE" position for extended periods of time when the water tank is em ...
-
Hoshizaki KML-700MWH-M - page 19
19 3) Open the condenser water supply line drain valve. If connected to a closed loop system, also open the condenser return line drain valve. 4) Attach a compressed air or carbon dioxide supply to the condenser water supply line drain valve. 5) Open the water regulating valve by using a screwdriver to pry up on the spring retainer underneath the s ...
-
Hoshizaki KML-700MWH-M - page 20
0 HOSHIZAKI AMERICA, INC. 618 Hwy . 74 S., Peachtree City , GA 30269 USA TEL (770) 487-2331 F AX (770) 487-3360 www .hoshizaki.com 91A1HL10A ...
Avez-vous une question à propos de Hoshizaki KML-700MWH-M?
Utiliser le formulaire ci-dessous
Si vous n’avez pas résolu votre problème avec Hoshizaki KML-700MWH-M, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Hoshizaki KML-700MWH-M il est probable qu’il a envie de partager la façon de le résoudre.