-
Pelco C1602M - page 1
DX8000-256RAM Installation Manual C1602M (6/04) Digital Video Recorder DX8000 ...
-
Pelco C1602M - page 2
Protecting people and property in a million locations worldwide. ...
-
Pelco C1602M - page 3
C1602M (6/04) 1 Introduction The following instructions serve as a guide for the installation of the DX8000-256RAM memory expansion module. PARTS LIST Qty Description 1 256 MB double data rate (DDR) dual inline memory module (DIMM) 1 Adhesive-backed upgrade part label Figure 1. 256 MB DIMM Module TOOLS NEEDED 1 Phillips-head screwdriver #1 (nonmagn ...
-
Pelco C1602M - page 4
2 C1602M (6/04) Getting Ready 1. Familiarize yourself with the instructions throughout this manual. 2. Check that you have all the necessary parts and tools. Refer to the Parts List and T ools Needed sections. 3. Shut down the DX8000 Series DVR unit. Refer to DX8000 Installation Manual or Operations and Programming Manual for instructions on shutti ...
-
Pelco C1602M - page 5
C1602M (6/04) 3 Figure 3. Removing Power Cord from Unit ...
-
Pelco C1602M - page 6
4 C1602M (6/04) Figure 4. ESD Protection 5. Ensure that the DX8000 Series DVR and all of its components are protected against electrostatic discharge (ESD). Before handling any electronic components, you should take steps to ground yourself properly so that any built-up static electric charges are dissipated away from the unit. The most effective m ...
-
Pelco C1602M - page 7
C1602M (6/04) 5 Prepare Unit for RAM Installation OPEN THE UNIT CHASSIS WARNING: The chassis assembly includes parts with sharp edges. T o avoid injury , use caution when working in and around the DX8000’ s chassis and components. 1. If the DX8000 is mounted in a rack, remove it and transport it to an area that will provide full access to the uni ...
-
Pelco C1602M - page 8
6 C1602M (6/04) 3. Using a Phillips-head screwdriver , remove the chassis cover: WARNING: Make sure unit is turned off and you are wearing a properly grounded ESD wrist strap before attempting to open the DX8000 chassis cover . Refer to the Getting Ready section. a. Remove the two top-most screws on the left and right side panels of the DX8000. Ref ...
-
Pelco C1602M - page 9
C1602M (6/04) 7 COMPONENT LA YOUT Figure 6 shows the location of your DX8000 Series DVR’ s major components. Certain cables and components have been omitted from the illustrations in this manual for the purpose of clarity . Figure 6. DX8000 Interior POWER SUPPLY DIMM SOCKETS (RAM) CPU VGA CARD PCI SLOT 1 2 3 4 5 6 REAR CROSS-BRACE FRONT CROSS-BRA ...
-
Pelco C1602M - page 10
8 C1602M (6/04) Install the DX8000-256RAM Memory Module 1. Carefully remove the DX8000-256RAM DIMM module from its static-safe packaging. Handle the DIMM by its edges and avoid contact with the module’ s chips or conductive leads. 2. Locate the first empty DIMM socket. This socket is directly adjacent to the socket containing the existing DIMM mo ...
-
Pelco C1602M - page 11
C1602M (6/04) 9 3. Align the DIMM module with the socket so that the notch in the module lines up properly with the break in the DIMM socket. Refer to Figure 8. 4. Make sure that the white retaining clips are not in the locked position by pressing outward and down on each clip. Refer to Figure 8. Figure 8. DIMM Module and DIMM Socket Alignment 3 4 ...
-
Pelco C1602M - page 12
10 C1602M (6/04) 5. Carefully , but firmly , push the DIMM module into the empty socket until it is properly seated. The module is properly seated when the retaining clips snap back into place as in Figure 9. NOTE: When inserting the DIMM module into the socket, use enough pressure to ensure that the retaining clips snap back into place. Be careful ...
-
Pelco C1602M - page 13
C1602M (6/04) 11 Reassemble the Unit 1. Replace the chassis cover using the same screws you removed from the side and rear of the unit. Refer to Figure 10. Figure 10. Replacing Chassis Cover ...
-
Pelco C1602M - page 14
12 C1602M (6/04) 2. Attach the silver part label that came in your upgrade kit to the inside of your DVR’ s front door . a. Remove the paper backing from the part label. b. Carefully place the label, adhesive-side down, on a free section of the inside of the door . c. Press down firmly to ensure that the label properly adheres to the inside of th ...
-
Pelco C1602M - page 15
C1602M (6/04) 13 3. Reinstall the unit in a rack enclosure if necessary , and reconnect all cables and peripheral equipment that you removed earlier . 4. Plug the power cord back into the power supply and then into the wall. 5. T urn on the power switch and allow the unit to start up and find the new memory . This may take several minutes. Figure 1 ...
-
Pelco C1602M - page 16
14 C1602M (6/04) V erify Installation of New RAM 1. After the DX8000 application starts, log in as an administrator level user and exit to the Windows ® operating system. Refer to the Installation or Operations and Programming manuals that came with your unit for instructions. 2. Go to Start > Settings > Control Panel. The Control Panel wind ...
-
Pelco C1602M - page 17
C1602M (6/04) 15 4 4. V erify that the amount of RAM is now 512 MB. Refer to Figure 15. Figure 15. System Properties Dialog Box 5. Click OK to exit the System Properties dialog box. 6. Go to Start > Programs > DX8000 to start the DX8000 application and return the unit to service. ...
-
Pelco C1602M - page 18
16 C1602M (6/04) Notes ...
-
Pelco C1602M - page 19
PRODUCT WARRANTY AND RETURN INFORMA TION PRODUCT WARRANTY AND RETURN INFORMA TION W ARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on the following fixed camera models ...
-
Pelco C1602M - page 20
C1602M (6/04) ® Pelco and the Pelco logo are registered trademarks of Pelco. © Copyright 2004, Pelco. All rights reserved. W orldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 United States | Canada | ...
Avez-vous une question à propos de Pelco C1602M?
Utiliser le formulaire ci-dessous
Si vous n’avez pas résolu votre problème avec Pelco C1602M, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Pelco C1602M il est probable qu’il a envie de partager la façon de le résoudre.