Français dropdown-ico

Manuel d’utilisation Cisco CX-TRIP2

28 pages 0.66 mb
Télécharger

Aller à la page of 28

Summary
  • Cisco CX-TRIP2 - page 1

    1 Customer Order Number: Copyright © 1995 Cisco Systems, Inc. All rights reser ved. Documentation P ar t Number: T ok en Ring Interf ace Processor (TRIP) Installation and Configuration Product Number s: CX-TRIP2 and CX-TRIP4 This document provides instructions for installing the T oken Ring interface processor (TRIP) in your Cisco 7000 and Cisco ...

  • Cisco CX-TRIP2 - page 2

    2 T ok en Ring Interface Processor (TRIP) Installation and Configur ation Product Description Pr oduct Description This section contains a detailed description of the T oken Ring interface processor (TRIP). The TRIP , shown in Figure 1, provides tw o or four T oken Ring ports for interconnection with IEEE 802.5 and IBM T oken Ring media. The TRIP ...

  • Cisco CX-TRIP2 - page 3

    Token Ring Interface Processor (TRIP) Installation and Configuration 3 Product Description When a T oken Ring interface is configured by using software commands, three LEDs for each port indicate the follo wing: • 16 Mbps—Lights if the interface is operating at 16 Mbps. • 4 Mbps—Lights if the interface is operating at 4 Mbps. • In Ring? ...

  • Cisco CX-TRIP2 - page 4

    4 T ok en Ring Interface Processor (TRIP) Installation and Configur ation Product Description Figure 3 T oken Ring T ype 3 Lobe Cable Connectors, DB-9 and RJ-11 T ypes T oken Ring Ph ysical Connections The term T oken Ring refers to both IBM’ s T oken Ring Network, which IBM de veloped in the 1970s, and to IEEE 802.5 networks. The IEEE 802.5 spe ...

  • Cisco CX-TRIP2 - page 5

    Token Ring Interface Processor (TRIP) Installation and Configuration 5 Product Description In the typical T oken Ring network sho wn in Figure 4, lobe cables connect each T oken Ring station (TRIP port) to the MSA U (or MA U), and patch cables connect adjacent MSA Us (or MA Us) to form one large ring. Figure 4 T oken Ring Network Physical Connectio ...

  • Cisco CX-TRIP2 - page 6

    6 T ok en Ring Interface Processor (TRIP) Installation and Configur ation Product Description What is the Cisco 7000 Series? Network interfaces reside on modular interf ace processors, which provide a direct connection between your external netw ork and the high speed Cisco Extended Bus (CxBus) in the Cisco 7000 series routers, and the CyBus in th ...

  • Cisco CX-TRIP2 - page 7

    Token Ring Interface Processor (TRIP) Installation and Configuration 7 Product Description Figure 6 Cisco 7010, Interface Processor End H2359 RP slot SP or SSP slot Interface processor slot 1 DC OK LED Power switch Chassis ground screw Power receptacle Interface processor slot 2 Interface processor slot 0 AC-input power supply ...

  • Cisco CX-TRIP2 - page 8

    8 T ok en Ring Interface Processor (TRIP) Installation and Configur ation Product Description What is the Cisco 7500 Series? The Cisco 7500 series consists of three router models: the Cisco 7505, the Cisco 7507, and the Cisco 7513. All three models provide high reliability , av ailability , serviceability , and performance. The three systems suppo ...

  • Cisco CX-TRIP2 - page 9

    Token Ring Interface Processor (TRIP) Installation and Configuration 9 Product Description Figure 8 shows the rear of the se ven-slot Cisco 7507 router . In the Cisco 7507, up to two slots (2 and 3) are reserved for the Route Switch Processor (RSP2), which contains the system processor and performs packet switching functions. Slots 0 and 1, and 4 t ...

  • Cisco CX-TRIP2 - page 10

    10 T ok en Ring Interface Processor (TRIP) Installation and Configur ation Product Description Figure 9 sho ws the rear of the Cisco 7513, with two A C-input power supplies installed. T wo slots (6 and 7) are reserved for the second generation Route Switch Processor (RSP2), which contains the system processor and performs packet switching function ...

  • Cisco CX-TRIP2 - page 11

    Token Ring Interface Processor (TRIP) Installation and Configuration 11 Installation Prerequisites Installation Prerequisites This section provides a list of parts and tools you will need to perform the installation, and safety and ESD-pre vention guidelines to help you to a void injury and damage to the equipment. It also provides a detailed descr ...

  • Cisco CX-TRIP2 - page 12

    12 T ok en Ring Interface Processor (TRIP) Installation and Configur ation Installation Prerequisites T elephone Wir ing Saf ety Use the following guidelines when w orking with any equipment that is connected to telephone wiring or to other network cabling: • Ne ver install telephone wiring during a lightning storm. • Ne ver install telephone ...

  • Cisco CX-TRIP2 - page 13

    Token Ring Interface Processor (TRIP) Installation and Configuration 13 Installation Prerequisites Online Inser tion and Remov al—An Ov er vie w Online insertion and remov al (OIR) allo ws you to remov e and replace interface processors while the system is operating; you do not need to notify the software or shut do wn the system po wer . This se ...

  • Cisco CX-TRIP2 - page 14

    14 T ok en Ring Interface Processor (TRIP) Installation and Configur ation Installation Prerequisites The function of the ejector lev ers (see Figure 10) is to align and seat the card connectors in the backplane. Failure to use the ejectors and insert the interf ace processor properly can disrupt the order in which the pins make contact with the b ...

  • Cisco CX-TRIP2 - page 15

    Token Ring Interface Processor (TRIP) Installation and Configuration 15 Installation Prerequisites Figure 10 Ejector Lever s and Captive Installation Screws Interface processor card slot Interface processor card carrier guide (black) Ejector lever Captive installation screw H1984 a b c ...

  • Cisco CX-TRIP2 - page 16

    16 T ok en Ring Interface Processor (TRIP) Installation and Configur ation Installation List of P ar ts and T ools V erify that you ha ve all of the parts and optional equipment you will need to install the TRIP . If you need additional equipment, contact a service representativ e for ordering information. • One TRIP • One T oken Ring 802.5 me ...

  • Cisco CX-TRIP2 - page 17

    Token Ring Interface Processor (TRIP) Installation and Configuration 17 Installation Step 4 Store the interface processor filler for future use. T o help prevent dust and contaminants from entering the chassis, do not lea v e the interface processor slot open. Immediately proceed to the section “Installing a TRIP” on page 18. Removing a TRIP T ...

  • Cisco CX-TRIP2 - page 18

    18 T ok en Ring Interface Processor (TRIP) Installation and Configur ation Installation Step 5 Place the remov ed TRIP on an antistatic mat or foam pad, or place it in an antistatic bag if you will return it to the factory . Step 6 If the interface processor slot is to remain empty , install an interface processor filler (MAS7K-BLANK) to keep dus ...

  • Cisco CX-TRIP2 - page 19

    Token Ring Interface Processor (TRIP) Installation and Configuration 19 Checking the Installation Step 7 Attach network interface cables or other connection equipment to the interf ace ports. (See Figure 12). Figure 12 T oken Ring Connections Step 8 Check the status of the interfaces as follo ws: • If this installation was a replacement TRIP , us ...

  • Cisco CX-TRIP2 - page 20

    20 T ok en Ring Interface Processor (TRIP) Installation and Configur ation Configuring the Interfaces Figure 13 TRIP LEDs Configuring the Interfaces Y ou can modify the startup configuration for Cisco 7000 series and Cisco 7500 series routers through the software command interpreter called EXEC . T o configure the interfaces for interface proc ...

  • Cisco CX-TRIP2 - page 21

    Token Ring Interface Processor (TRIP) Installation and Configuration 21 Configuring the Interfaces T o configure T oken Ring interfaces using the setup EXEC command f acility , follow the instructions in the section “Using the Setup Command” on page 21. T o configure the T oken Ring interfaces by using the configure EXEC command, follo w the ...

  • Cisco CX-TRIP2 - page 22

    22 T ok en Ring Interface Processor (TRIP) Installation and Configur ation Configuring the Interfaces Step 3 Proceed through the remainder of the global parameter prompts, using the Return key to accept the defaults. After the global parameters are configured, the system prompts you for interface configuration information, one interface at a ti ...

  • Cisco CX-TRIP2 - page 23

    Token Ring Interface Processor (TRIP) Installation and Configuration 23 Configuring the Interfaces Basic Configuration Guidelines Follo wing are instructions for a basic configuration: enabling an interface and specifying IP routing. Y ou might also need to enter other configuration subcommands, depending upon the requirements for your system co ...

  • Cisco CX-TRIP2 - page 24

    24 T ok en Ring Interface Processor (TRIP) Installation and Configur ation Checking the Configuration Chec king the Configuration After configuring the ne w interface(s) using either the setup command or the configure command, use the EXEC show commands to display status information. Step 1 T o display the current system configuration file, ...

  • Cisco CX-TRIP2 - page 25

    Token Ring Interface Processor (TRIP) Installation and Configuration 25 Upgrading Microcode Upgrading Micr ocode Depending on how it is configured, the Cisco 7000 series router allo ws the Switch Processor (SP) and interface processors to use updated microcode that is a vailable either in Flash memory on the Route Processor (RP) or on the onboard ...

  • Cisco CX-TRIP2 - page 26

    26 T ok en Ring Interface Processor (TRIP) Installation and Configur ation Upgrading Microcode Step 5 Confirm that you want the file copied into Flash: Copy trip1-0 from 131.108.13.111 into flash memory? [confirm] yes Step 6 If you do not want the other microcode files in Flash memory erased, enter no OR If you want Flash erased, enter ye s . E ...

  • Cisco CX-TRIP2 - page 27

    Token Ring Interface Processor (TRIP) Installation and Configuration 27 Upgrading Microcode Step 13 V erify that the correct microcode v ersion is av ailable in Flash memory: Router# show controllers token Y ou ha ve no w completed do wnloading microcode to the Flash memory , downloaded the microcode to the TRIP , added the microcode commands to th ...

  • Cisco CX-TRIP2 - page 28

    28 T ok en Ring Interface Processor (TRIP) Installation and Configur ation Cisco Information Online Cisco Inf ormation Online Cisco Information Online (CIO) is Cisco Systems’ primary , real-time support channel. Maintenance customers and partners can self-register on CIO to obtain additional content and services. A vailable 24 hours a day , 7 da ...

Fabricant Cisco Catégorie Network Card

Les documents que nous recevons du fabricant de l'appareilCisco CX-TRIP2 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Cisco
- manuels d’utilisations CX-TRIP2
- fiches produit Cisco
- dépliants
- ou étiquettes-énergie Cisco CX-TRIP2
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Cisco CX-TRIP2.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Cisco CX-TRIP2, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Cisco CX-TRIP2. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Cisco CX-TRIP2.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Cisco CX-TRIP2, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Cisco CX-TRIP2 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Cisco CX-TRIP2.

Le manuel d’utilisation complet Cisco, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Cisco CX-TRIP2 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Cisco CX-TRIP2, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lCisco CX-TRIP2 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Cisco CX-TRIP2 - qui devraient nous aider dans les premières étapes lors de l'utilisation Cisco CX-TRIP2
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Cisco CX-TRIP2
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Cisco CX-TRIP2 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Cisco CX-TRIP2?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Cisco CX-TRIP2, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Cisco CX-TRIP2 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)