Français dropdown-ico

Manuel d’utilisation NETGEAR SW108

40 pages 1.12 mb
Télécharger

Aller à la page of 40

Summary
  • NETGEAR SW108 - page 1

    M-SW108NA-0 June 1997 NETGEAR , Inc. A Bay Networks Company 48015 Warm Springs Blvd. Fremont, CA 94539 USA Installation Guide f or the Model SW108 Ethernet Switc h SW108.BK Page i Friday, June 27, 1997 10:48 AM ...

  • NETGEAR SW108 - page 2

    ii © 1997 by NETGEAR, Inc. All rights reserved. T rademarks Bay Networks is a registered trademark of Bay Netw orks, Inc. NETGEAR is a trademark of Bay Networks, Inc. Other brand and product names are registered trademarks or trademarks of their respecti ve holders. Statement of Conditions In the interest of improving internal design, operational ...

  • NETGEAR SW108 - page 3

    iii V oluntar y Contr ol Council for Interference (VCCI) Statement This equipment is in the first category (information equipment to be used in commercial and/or industrial areas) and conforms to the standards set by the V oluntary Control Council for Interference by Data Processing Equipment and Electronic Office Machines that are aimed at pre v ...

  • NETGEAR SW108 - page 4

    iv SW108.BK Page iv Friday, June 27, 1997 10:48 AM ...

  • NETGEAR SW108 - page 5

    Contents v Contents Chapter 1 Introduction Benefits of Using Switching T echnology ......................................................................... 1-1 T ypes of Ethernet Switches ............................................................................................ 1-2 Model SW108 Switch Ov er vie w ................................ ...

  • NETGEAR SW108 - page 6

    vi Contents Chapter 5 T roub leshooting T roub leshooting the Switch and the Networ k ................................................................. 5-1 Appendix A T echnical Specifications General Specifications ................................................................................................... A-1 Appendix B Connector Pin Ass ...

  • NETGEAR SW108 - page 7

    Figures vii Figures Figure 2-1. F ront panel of the Model SW108 switch .................................................. 2-1 Figure 2-2. The vista RJ-45 connector with built-in LEDs .......................................... 2-2 Figure 2-3. Rear panel of the Model SW108 s witch ................................................... 2-4 Figure 3-1. Us ...

  • NETGEAR SW108 - page 8

    viii Tables T ab les T able 2-1. LED descriptions ...................................................................................... 2-3 T able 5-1. T roubleshooting ........................................................................................ 5-1 T able B-1. RJ-45 plug and vista RJ-45 connector pin assignments ...................... ...

  • NETGEAR SW108 - page 9

    Introduction 1-1 Chapter 1 Intr oduction Congratulations on your purchase of the NETGEAR ™ Model SW108 8-port Ethernet Switch. The Model SW108 switch segments Ethernet netw orks to relieve bandwidth congestion instantly , without having to replace netw ork wiring, interface cards, or software. This guide describes ho w to install and use the swit ...

  • NETGEAR SW108 - page 10

    Installation Guide for the Model SW108 Ethernet Switch 1-2 Introduction This bandwidth improv ement is accomplished very easily , with no change to the desktop (the network interface cards or softw are, and network wiring). As a result, the performance upgrade and the applications it enables are obtained very quickly and at a lo w cost. T ypes of E ...

  • NETGEAR SW108 - page 11

    Installation Guide for the Model SW108 Ethernet Switch Introduction 1-3 Features The Model SW108 switch has the follo wing key features: • Eight switched, 10 Mbps, Ethernet 10B ASE-T ports • Full-duplex or half-duple x mode of operation Full-duplex mode doubles throughput of point-to-point connections by letting indi vidual ports transmit and r ...

  • NETGEAR SW108 - page 12

    SW108.BK Page 4 Friday, June 27, 1997 10:48 AM ...

  • NETGEAR SW108 - page 13

    Physical Description 2-1 Chapter 2 Ph ysical Description This chapter explains the hardw are features of the NETGEAR Model SW108 Ethernet switch. It is di vided into sections explaining the front and rear panels of the switch. Use the key at the bottom of each illustration to identify the panel components. Fr ont Panel For easier management and con ...

  • NETGEAR SW108 - page 14

    Installation Guide for the Model SW108 Ethernet Switch 2-2 Physical Description Ethernet P or ts The Model SW108 switch is equipped with eight 10 Mbps Ethernet ports that support one cable connection, unshielded twisted pair (UTP) cable. An eight-pin RJ-45 plug is used for connection to these ports. Each port uses vista RJ-45 connectors that hav e ...

  • NETGEAR SW108 - page 15

    Installation Guide for the Model SW108 Ethernet Switch Physical Description 2-3 LEDs Y ou use LEDs on the Model SW108 switch to monitor and diagnose the devices. LEDs on the front panel of the switch and two LEDs on each port allo w you to identify the following information: • Status of the switch po wer supply • Data transmission or recei ve a ...

  • NETGEAR SW108 - page 16

    Installation Guide for the Model SW108 Ethernet Switch 2-4 Physical Description Rear P anel As illustrated in Figure 2-3, the rear panel has full-duplex (FDX), and half-duple x (HDX) toggle switches, a ground clip, and a standard AC po wer receptacle. Key : 1 = Ground clip 2 = FDX and HDX toggle switches to set the duple x mode of each 10 Mbps por ...

  • NETGEAR SW108 - page 17

    Applications 3-1 Chapter 3 Applications This chapter presents an ov erview of the le vels of service provided by incorporating the technology of the NETGEAR Model SW108 Ethernet switch into your network. The Model SW108 Ethernet switch is designed to provide fle xibility in configuring your network connections. Each switch can be used as a standa ...

  • NETGEAR SW108 - page 18

    Installation Guide for the Model SW108 Ethernet Switch 3-2 Applications Desktop Switching Figure 3-1 illustrates the Model SW108 switch used as a desktop switch to build a small netw ork that enables users to hav e 10 Mbps access to a file server . Key : 1 = Server with 10 Mbps connection 2 = Model SW108 Ethernet switch (Normal/Uplink push button ...

  • NETGEAR SW108 - page 19

    Installation Guide for the Model SW108 Ethernet Switch Applications 3-3 Segment Switching The Model SW108 switch can segment a netw ork into multiple connected pieces, increasing ov erall bandwidth and throughput. Figure 3-2 illustrates the Model SW108 Ethernet switch segmenting netw orks that are built with the NETGEAR Model EN104 and Model EN108 ...

  • NETGEAR SW108 - page 20

    SW108.BK Page 4 Friday, June 27, 1997 10:48 AM ...

  • NETGEAR SW108 - page 21

    Installation 4-1 Chapter 4 Installation This chapter provides information about installing the Model SW108 Ethernet switch and information about verifying installation. Preparing the Site Before you begin installing the switch, prepare the installation site. Mak e sure the operating en vironment meets the physical requirements of the equipment as d ...

  • NETGEAR SW108 - page 22

    Installation Guide for the Model SW108 Ethernet Switch 4-2 Installation Installing the Switch on a Desktop Choose a location near the de vices to be connected and close to an electrical outlet. Set the switch on a desktop or tabletop, allo wing at least two inches (5 cm) of space on all sides to prev ent restriction of airflo w . Connecting Device ...

  • NETGEAR SW108 - page 23

    Installation Guide for the Model SW108 Ethernet Switch Installation 4-3 3. Set the FDX or HDX toggle switches on the rear panel f or the selected duplex mode. A hub and repeater use a common collision domain for all communications and cannot support full-duplex mode. When connecting any of the 10 Mbps ports on the switch to a hub, set the port to H ...

  • NETGEAR SW108 - page 24

    SW108.BK Page 4 Friday, June 27, 1997 10:48 AM ...

  • NETGEAR SW108 - page 25

    Troubleshooting 5-1 Chapter 5 T roub leshooting This chapter provides information about troubleshooting the NETGEAR Model SW108 Ethernet switch. T roub leshooting the Switch and the Network T o troubleshoot the switch and the network, refer to T able 5-1. T able 5-1. T roub leshooting Symptom Activity Check No pow er at switch P ow er LED off Check ...

  • NETGEAR SW108 - page 26

    Installation Guide for the Model SW108 Ethernet Switch 5-2 Troubleshooting P or t connection not functioning Link LED off or intermittent After the cabling has been installed, if the Link LED is not lit on an active port, check the attached de vice and mak e sure that it is powered on and there is a proper UTP connection at that end. Also make sure ...

  • NETGEAR SW108 - page 27

    Technical Specifications A-1 Appendix A T echnical Specifications This appendix provides technical specifications for the NETGEAR Model SW108 switch. General Specifications Network Pr otocol and Standard ISO/IEC 802-3 (ANSI/IEEE 802.3i 10B ASE-T , Ethernet Data Rate 10 Mbps Manchester encoded Interface RJ-45 connector for 10B ASE-T Ethernet inte ...

  • NETGEAR SW108 - page 28

    Installation Guide for the Model SW108 Ethernet Switch A-2 Technical Specifications En vironmental Specifications Operating temperature: 0 ° to 40 ° C (32 ° to 104 ° F) Storage temperature: -25 ° to 70 ° C (-13 ° to 158 ° F) Operating humidity: 80% maximum relati ve humidity , noncondensing Storage humidity: 95% maximum relati ve humidity ...

  • NETGEAR SW108 - page 29

    Installation Guide for the Model SW108 Ethernet Switch Technical Specifications A-3 Safety Agency Appr ovals f or P ower Adapter CE mark, commercial UL listed (UL 1950 ) CSA certified (CSA 22.2 #950) TUV licensed (EN 60 950) T -Mark P erformance Specifications Frame filter rate: 14,800 frames/second, maximum Frame forward rate: 14,800 frames/sec ...

  • NETGEAR SW108 - page 30

    SW108.BK Page 4 Friday, June 27, 1997 10:48 AM ...

  • NETGEAR SW108 - page 31

    Connector Pin Assignments B-1 Appendix B Connector Pin Assignments This appendix provides information about the RJ-45 connector used for the NETGEAR Model SW108 Ethernet switch. RJ-45 Plug and vista RJ-45 Connector The RJ-45 plug accepts 4-pair unshielded twisted pair (UTP) or shielded twisted pair (STP) 100 Ω cable and connects into the vista RJ ...

  • NETGEAR SW108 - page 32

    Installation Guide for the Model SW108 Ethernet Switch B-2 Connector Pin Assignments T able B-1 lists the pin assignments for the RJ-45 plug and the vista RJ-45 connector . * Applicable to port1 on the Model SW108 switch, when the Normal/Uplink push button is in the Uplink position. T able B-1. RJ-45 plug and vista RJ-45 connector pin assignments P ...

  • NETGEAR SW108 - page 33

    Cabling Guidelines C-1 Appendix C Cabling Guidelines This appendix provides information on the cable specifications and guidelines for Cate gory 5 UTP cabling used with the NETGEAR Model SW108 Ethernet switch. Ethernet T echnology When 10B ASE-T technology was originally introduced, multiple repeaters were frequently used to build lar ge netw orks ...

  • NETGEAR SW108 - page 34

    Installation Guide for the Model SW108 Ethernet Switch C-2 Cabling Guidelines T able C-1 lists the electrical requirements of the Category 3, 4, and 5 cables. T wisted P air Cables For tw o devices to communicate, the transmitter of each de vice must be connected to the recei ver of the other device. The crossover function is usually implemented in ...

  • NETGEAR SW108 - page 35

    Installation Guide for the Model SW108 Ethernet Switch Cabling Guidelines C-3 Figure C-1 illustrates straight-through twisted pair cable connections. Key : A = Uplink or MDI por t (As on a PC) B = Normal or MDI-X por t (As on a hub or switch) 1, 2, 3, 6 = Connector pins Figure C-1. Straight-through twisted pair cab le Figure C-2 illustrates crossov ...

  • NETGEAR SW108 - page 36

    SW108.BK Page 4 Friday, June 27, 1997 10:48 AM ...

  • NETGEAR SW108 - page 37

    Index 1 Numbers 10 Mbps ports, 2-1, 2-4 A applications desktop switching, 3-2 segment switching, 3-3 C cable crossov er twisted pair, 4-2, C-3 specifications, C-1 straight-through twisted pair , 4-2, 5-2, C-3 troubleshooting, 5-2 Collision LED, 2-1, 2-3, 5-1 crossov er twisted pair cable, 4-2, C-3 customer support, iii D data collisions, 5-1 deskt ...

  • NETGEAR SW108 - page 38

    Installation Guide for the Model SW108 Ethernet Switch 2 Index P package contents, 4-1 ports, 10 Mbps, 2-1, 2-4 Power LED, 2-1, 2-3, 4-3, 5-1 R rear panel, 2-4 RJ-45 connector . See vista RJ-45 connector RJ-45 plug using to connect to 10 Mbps ports, 2-2 using with UTP and STP cable, B-1 Rx/Tx LED, 2-3, 4-3, 5-1 S segment switching, 1-2, 3-3 site pr ...

  • NETGEAR SW108 - page 39

    SW108.BK Page 3 Friday, June 27, 1997 10:48 AM ...

  • NETGEAR SW108 - page 40

    SW108.BK Page 4 Friday, June 27, 1997 10:48 AM ...

Fabricant NETGEAR Catégorie Computer Monitor

Les documents que nous recevons du fabricant de l'appareilNETGEAR SW108 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques NETGEAR
- manuels d’utilisations SW108
- fiches produit NETGEAR
- dépliants
- ou étiquettes-énergie NETGEAR SW108
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation NETGEAR SW108.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation NETGEAR SW108, manuels d’entretien, brefs manuels ou manuels de l’utilisateur NETGEAR SW108. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit NETGEAR SW108.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil NETGEAR SW108, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser NETGEAR SW108 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs NETGEAR SW108.

Le manuel d’utilisation complet NETGEAR, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel NETGEAR SW108 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières NETGEAR SW108, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lNETGEAR SW108 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil NETGEAR SW108 - qui devraient nous aider dans les premières étapes lors de l'utilisation NETGEAR SW108
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de NETGEAR SW108
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service NETGEAR SW108 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de NETGEAR SW108?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec NETGEAR SW108, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec NETGEAR SW108 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)