Français dropdown-ico

Manuel d’utilisation GE JVM1790

24 pages 3.01 mb
Télécharger

Aller à la page of 24

Summary
  • GE JVM1790 - page 1

    Questions? Call 1-800-361-3400 or Visit our W ebsite at: geappliances.ca READ CAREFULL Y . KEEP THESE INSTRUCTIONS . Read these instr uctions completely and carefully . • IMPORT ANT – Save these instructions for local inspector’ s use. • IMPORT ANT – Obser ve all governing codes and ordinances. • Note to Installer – Be sure to leave t ...

  • GE JVM1790 - page 2

    2 Recirculating ........................................ 19–22 Attach Mounting Plate to W all ............19 Preparation of T op Cabinet ................19 Adapting Blower for Recirculation ..........................20, 21 Mount the Oven ............................21, 22 Installing the Charcoal Filter ..............22 Before Y ou Use Y our Oven ...

  • GE JVM1790 - page 3

    This product requires a three-prong grounded outlet. The installer must per form a ground continuity check on the power outlet box before beginning the installation to insure that the outlet box is properly grounded. If not properly grounded, or if the outlet box does not meet electrical requirements noted (under ELECTRICAL REQUIREMENTS), a qualifi ...

  • GE JVM1790 - page 4

    4 EQUIV ALENT NUMBER EQUIV ALENT DUCT PIECES LENGTH x USED = LENGTH Roof Cap 24 Ft. (7.3 m) x (1) = 24 Ft. (7.3 m) 12 Ft. (3.6 m) Straight Duct 12 Ft. (3.6 m) x (1) = 12 Ft. (3.6 m) (6”/15.2 cm Round) Rectangular -to-Round 5 Ft. (1.5 m) x (1) = 5 Ft. (1.5 m) T ransition Adaptor* Equivalent lengths of duct pieces are based on actual tests and refl ...

  • GE JVM1790 - page 5

    EQUIV ALENT NUMBER EQUIV ALENT DUCT PIECES LENGTH x USED = LENGTH Rectangular -to-Round 5 Ft. (1.5 m) x ( ) = Ft. or m T ransition Adaptor* Wall Cap 40 Ft. (12.2 m) x ( ) = Ft. or m 90° Elbow 10 Ft. (3 m) x ( ) = Ft. or m 45° Elbow 5 Ft. (1.5 m) x ( ) = Ft. or m 90° Elbow 25 Ft. (7.6 m) x ( ) = Ft. or m 45° Elbow 5 Ft. (1.5 m) x ( ) = Ft. or m ...

  • GE JVM1790 - page 6

    PA R T QUANTITY T op Cabinet 1 T emplate Rear Wall 1 T emplate Installation 1 Instructions Separately 2 Packed Grease Filters P ART QUANTITY Wood Screws 2 ( 1 ⁄ 4 “ x 2“) T oggle Bolts (and 4 wing nuts) ( 1 ⁄ 4 “ x 3“) Self-Aligning Machine 2 Screws ( 1 ⁄ 4 “-28 x 3 1 ⁄ 4 “) Self-Aligning Machine 1 Screw ( 1 ⁄ 4 “-28 x 2 5 ? ...

  • GE JVM1790 - page 7

    7 TOOLS YOU WILL NEED #1 and #2 Phillips screwdriver Pencil Ruler or tape measure and straight edge Carpenter square (optional) T in snips (for cutting damper , if required) Electric drill with 3 ⁄ 16 “ , 7 ⁄ 16 “ 1 ⁄ 2 “ and 5 ⁄ 8 “ drill bits Hammer (optional) Stud finder or Filler blocks or scrap wood pieces, if needed for top ca ...

  • GE JVM1790 - page 8

    8 Find the studs, using one of the following methods: A. Stud finder – a magnetic device which locates nails. OR B. Use a hammer to tap lightly across the mounting sur face to find a solid sound. This will indicate a stud location. After locating the stud(s), find the center by probing the wall with a small nail to find the edges of the stud. The ...

  • GE JVM1790 - page 9

    9 DETERMINING W ALL PLA TE LOCA TION UNDER YOUR CABINET C. Y our cabinets may have decorative trim that inter feres with the oven installation. Remove the decorative trim to install the oven properly and to make it level. THE OVEN MUST BE LEVEL. Use a level to make sure the cabinet bottom is level. If the cabinets have a front over hang only , with ...

  • GE JVM1790 - page 10

    10 ALIGNING THE W ALL PLA TE Draw a vertical line on the wall at the center of the 30 ″ (76.2 cm) wide space. Use the mounting plate as the template for the rear wall. Place the mounting plate on the wall, making sure that the tabs are touching the bottom of the cabinet or the level line drawn in Step C for cabinets with front overhang. Line up t ...

  • GE JVM1790 - page 11

    A INST ALLA TION TYPES (Choose A, B or C) This oven is designed for adaptation to the following 3 types of ventilation: A. Outside T op Exhaust (V er tical Duct) B. Outside Back Exhaust (Horizontal Duct) C. Recirculating (Non-V ented Ductless) NOTE: This oven is shipped assembled for Outside T op Exhaust. Select the type of ventilation required for ...

  • GE JVM1790 - page 12

    Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate. NOTE: Before tightening toggle bolts and wood screw , make sure the tabs on the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet. CAUTION: Be ...

  • GE JVM1790 - page 13

    13 3 MOUNT THE OVEN A4. USE TOP CABINET TEMPLA TE FOR PREP ARA TION OF TOP CABINET Y ou need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adaptor . A2. FOR EASIER INST ALLA TION AND PERSONAL SAFETY , WE RECOMMEND THA T TWO PEOPLE INST ALL THIS OVEN. IMPOR ...

  • GE JVM1790 - page 14

    14 4 Attach the oven to the top cabinet. 8 7 6 Cabinet Front Cabinet Bottom Shelf Tighten the outer two screws to the top of the oven. (While tightening screws, hold the oven in place against the wall and the top cabinet.) Filler Block Oven T op Equivalent to Depth of Cabinet Recess Insert 2 self-aligning screws ( 1 ⁄ 4 ”-28 x 3 1 ⁄ 4 ”) th ...

  • GE JVM1790 - page 15

    INST ALLA TION OVERVIEW B1. Prepare Rear W all B2. Attach Mounting Plate to W all B3. Prepare T op Cabinet B4. Adjust Blower B5. Mount the Oven Installation Instructions 15 PREP ARING THE REAR W ALL FOR OUTSIDE BACK EXHAUST B1. Y ou need to cut an opening in the rear wall for outside exhaust. • Read the instructions on the REAR W ALL TEMPLA TE. ? ...

  • GE JVM1790 - page 16

    16 USE TOP CABINET TEMPLA TE FOR PREP ARA TION OF TOP CABINET B3. • Read the instructions on the TOP CABINET TEMPLA TE. • T ape it underneath the top cabinet. • Drill the holes, following the instructions on the TOP CABINET TEMPLA TE. CAUTION: W ear safety goggles when drilling holes in the cabinet bottom. Wal l Mounting Plate Spacing for T o ...

  • GE JVM1790 - page 17

    17 Installation Instructions Snip all 4 webs on each knockout panel and remove the metal knockouts for rear airflow . Locate the two “knockout” plates, on the rear oven panel, near the top of the oven. Using tin snips, carefully cut the web area from the two holes side-by-side (that secure the knockouts to the oven). Cut all four webs on both r ...

  • GE JVM1790 - page 18

    Attach the oven to the top cabinet. 18 Installation Instructions 3 MOUNT THE MICROW A VE OVEN B5. FOR EASIER INST ALLA TION AND PERSONAL SAFETY , WE RECOMMEND THA T TWO PEOPLE INST ALL THIS MICROW A VE OVEN. IMPORT ANT: Do not grip or use handle during installation. NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to ...

  • GE JVM1790 - page 19

    USE TOP CABINET TEMPLA TE FOR PREP ARA TION OF TOP CABINET C2. 19 INST ALLA TION OVERVIEW C1. Attach Mounting Plate to W all C2. Prepare T op Cabinet C3. Adjust Blower C4. Mount the Oven C5. Install Charcoal Filter (not supplied) • Read the instructions on the TOP CABINET TEMPLA TE. • T ape it underneath the top cabinet. • Drill the holes, fo ...

  • GE JVM1790 - page 20

    20 Installation Instructions AFTER: Fan Blade Openings Facing Forward 3 2 4 ADAPTING BLOWER FOR RECIRCULA TION C3. NOTE: The exhaust adaptor with damper is not needed for recirculating models. Y ou may want to save them for possible future use. Carefully pull out the blower unit. The wires will extend far enough to allow you to adjust the blower un ...

  • GE JVM1790 - page 21

    21 Attach the oven to the top cabinet. Cabinet Front Cabinet Bottom Shelf Filler Block Oven T op Equivalent to Depth of Cabinet Recess Installation Instructions 3 MOUNT THE OVEN C4. FOR EASIER INST ALLA TION AND PERSONAL SAFETY , WE RECOMMEND THA T TWO PEOPLE INST ALL THIS OVEN. IMPORT ANT: Do not grip or use handle during installation. NOTE: If yo ...

  • GE JVM1790 - page 22

    5 MOUNT THE OVEN (continued) C5. 22 Installation Instructions 8 7 6 Tighten the outer two screws to the top of the oven. (While tightening screws, hold the oven in place against the wall and the top cabinet.) Insert 2 self-aligning screws ( 1 ⁄ 4 ”-28 x 3 1 ⁄ 4 ”) through outer top cabinet holes. T urn two full turns on each screw . Tighten ...

  • GE JVM1790 - page 23

    KEEP INST ALLA TION INSTRUCTIONS FOR THE LOCAL INSPECTOR’S USE. Plug power cord into a dedicated 15 to 20 amp electrical outlet. 7. Read the Owner’ s Manual. 6. Replace house fuse or turn breaker back on. 4. Remove all packing material from the oven. 2. Make sure the oven has been installed according to instructions. 1. 23 BEFORE YOU USE YOUR M ...

  • GE JVM1790 - page 24

    49-40453 (06-05 JR) Printed in Korea 24 ...

Fabricant GE Catégorie Convection Oven

Les documents que nous recevons du fabricant de l'appareilGE JVM1790 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques GE
- manuels d’utilisations JVM1790
- fiches produit GE
- dépliants
- ou étiquettes-énergie GE JVM1790
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation GE JVM1790.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation GE JVM1790, manuels d’entretien, brefs manuels ou manuels de l’utilisateur GE JVM1790. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit GE JVM1790.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil GE JVM1790, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser GE JVM1790 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs GE JVM1790.

Le manuel d’utilisation complet GE, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel GE JVM1790 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières GE JVM1790, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lGE JVM1790 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil GE JVM1790 - qui devraient nous aider dans les premières étapes lors de l'utilisation GE JVM1790
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de GE JVM1790
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service GE JVM1790 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de GE JVM1790?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec GE JVM1790, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec GE JVM1790 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)