-
Boston Acoustics BT2 - page 1
Boston BT1 Boston BT2 Music & Cinema Loudspeaker Altavoz para música y cine Enceinte acoustique pour musique et home-cinéma Lautsprecher für Musik und Heimkino ...
-
Boston Acoustics BT2 - page 2
– 2 – A B C D E A B C D E 123456 123456 10 17 1 / 2 1 8 5 / 8 16 1 / 4 Front View Boston BT1 Dimension Sheet All Dimensions in inches. It is recommended that at least 0.75-inches of extra depth is added to the compartment for wiring and at 0.75-inches on either side to ease removal. For more information on the BT or any other Boston products, p ...
-
Boston Acoustics BT2 - page 3
Contents Thank Y ou! . . . . . . . . . . . . . . .4 Specifications . . . . . . . . . . . . .4 What's in the Box . . . . . . . . . .5 Placement/Location Tips . . . .5 Midrange/T weeter Positioning . . . . . . . . . . . . . . .7 Installation Tips . . . . . . . . . . .8 Screen/Cabinet Compensation . . . . . . . . . . . .9 Wiring . . . . . . . . . ...
-
Boston Acoustics BT2 - page 4
– 4 – Frequency R esponse (±3dB) R ecommended Amp Po wer Nominal Impedance Sensitivity (2.83v at 1m) Tw eeter Midrange Bass Unit Crossov er Frequency Width Height Depth w/grille Depth w/o grille *In keeping with our policy of continual product improvements, specifications ar e subject to change without notice. Please visit our Web site, www .b ...
-
Boston Acoustics BT2 - page 5
– 5 – What’ s in the Box • BT1/B T2 Speaker • Grille • Self-adhesive neoprene feet • Foam blocks • This Manual General Placement/ Location Tips Cabinet Placement If the BT speaker is going to be placed in a cabinet or in a confined location: • Maintain a minimum 3 / 4 -inch clearance on each side of the BT speaker . •F oam is pr ...
-
Boston Acoustics BT2 - page 6
– 6 – Music System Placement/ Location Tips F or optimum results in a music sy stem: • Place one speaker on each side of the listening area, equidistant from the listening area. •P osition the midrange/tweeter baffle using the guidelines listed on page 7. Home Theater Design Placement/Location Tips L/C/R (Left/Center/Right) When using the B ...
-
Boston Acoustics BT2 - page 7
– 7 – Positionnement du médium/tweeter Le médium/tweeter peut être placé en biais ou pivoter pour assurer des performances opti- males. Les consignes ci-après v ous permettront d’obtenir un position- nement correct. • Le haut-parleur médium/tweeter du BT1 et B T2 doit toujours être positionné de manière à conserver l’alignement ...
-
Boston Acoustics BT2 - page 8
– 8 – Installation Tips V ibration To av oid problems caused by vibration and to prevent scratching the finish, install the provided neoprene feet on the bottom of the speaker . When installing the BT speaker in a cabinet or shelf, make sure that the speaker’s enclo- sure does not make direct contact with the back, sides, or top of the cabine ...
-
Boston Acoustics BT2 - page 9
– 9 – Screen Compensation The Screen Compensation switch alters the response of the speaker to compensate for the absorption characteristics of a projection screen or thick grille cloth on a cab- inet. Depending on the thickness of the screen or cloth, this may or ma y not be needed. Try both settings and use the one that sounds best. Flush Mou ...
-
Boston Acoustics BT2 - page 10
– 10 – P ositioning and R otating the Midrange/Tw eeter (MT) Baffle 1. Position the speaker so the MT baffle is facing upw ard. 2. R emov e the four Phillips-head screws holding the MT baffle in place . 3. Gently tip the speaker on its side so that the MT baffle slides out. 4. To angle the MT baffle , detach the wiring harness, slide out the pl ...
-
Boston Acoustics BT2 - page 11
– 11 – Wiring There are three basic wa ys to con- nect the BT speakers to y our receiv- er or amplifier . • Basic •B i-Wiring • Bi-Amplification Basic Hookup This method only requires one pair of speaker wires, run from the amplifier or receiver to the speaker . 1. Connect the speaker terminals to the amplifier's speaker outputs. 2. ...
-
Boston Acoustics BT2 - page 12
– 12 – Bi-Amplification Bi-amplification requires using separate two-channel amplifiers , each dedicated to a speaker . Using more than one amplifier can enhance the dynamic performance of your s ystem. “Splitting the load” between tw o amplifiers lets each amplifier work less hard, increas- ing the av ailable current to the drive units , a ...
-
Boston Acoustics BT2 - page 13
– 13 – Front View Side View Foam Blocks Barrier Foam When placing a speaker inside of a cabinet, the performance can be optimized if the speaker's baf- fle is extended to the walls of the cabinet. We have pro vided foam blocks for filling in the area around the speaker in the cabinet. This allow s the baffle to extend out to the edge of th ...
-
Boston Acoustics BT2 - page 14
– 14 – Grille Installation A metal grille has been provided for protecting the drivers if the speakers are to be used out in the open. If your B T1 or BT2 speaker is going to be used behind a grille cloth door or projection screen you do not need to use the grille . Grille Installation Instructions 1. P osition one side of the grille into the s ...
-
Boston Acoustics BT2 - page 15
– 15 – Listening Levels/ Power Handling The pow er recommendations for the speakers assume that you will operate the amplifier in a wa y that will not produce distortion. Even our rugged speakers can be dam- aged by an amplifier if it is produc- ing distortion. If you hear a harsh, gritty sound, turn down the v olume . Prolonged or repeated ope ...
-
Boston Acoustics BT2 - page 16
AMD is a trademark of Boston Acoustics, Inc. Boston, Boston Acoustics, the Boston Acoustics logo, and VR are register ed trademarks of Boston Acoustics, Inc. Specifications are subject to change without notice. © 2003 Boston Acoustics, Inc. 300 Jubilee Drive Peabody , MA 01960 U.S.A. 978.538.5000 www .bostonacoustics.com 042-001591-0 ...
Hai una domanda su Boston Acoustics BT2?
Utilizza il modulo sottostante
Se non hai risolto il problema con Boston Acoustics BT2 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Boston Acoustics BT2 è probabile che voglia condividere il modo di risolverlo.