Italiano dropdown-ico

Manuale per l’uso Yamaha TX4n

60 pagine 1.31 mb
Scarica

Vai alla pagina of 60

Summary
  • Yamaha TX4n - page 1

    Reference Manual EN ...

  • Yamaha TX4n - page 2

    TX6n/5n/4n Reference Manual 2 Contents Introduction............................................. 3 About the documentation .......................................... 3 Setup ........................................................................... 3 Terms ........................................................................... 4 Controls and C ...

  • Yamaha TX4n - page 3

    TX6n/5n/4n Reference Manual 3 Intr oduction About the documentation This manual mainly explains operation and specifications f or the TX6n, TX5n, and TX4n (subsequently r eferred to as TXn) power amplifiers. When using the TXn, y ou will also need to consult various manuals other than this document. ● Manuals other than this document PDF manual ...

  • Yamaha TX4n - page 4

    TX6n/5n/4n Reference Manual 4 Introduction T erms This section explains terminology specific to the TXn. ■ Amp Editor This is computer application software. This softw are allo ws you to monitor and control the TXn amplifiers from your com- puter . ■ Scene Settings such as po wer-on/standby or mute for each amplifi er are called a “scene. ...

  • Yamaha TX4n - page 5

    TX6n/5n/4n Reference Manual 5 Contr ols and Connectors q [PO WER] switch and indicator This switch turns the amplifier’ s power on or of f. When you turn this switch on, the [PO WER] indicator will light white. In Standby mode, it will light white as well. w [ST ANDBY] indicator This indicator will light orange when the amplifier’ s po wer is ...

  • Yamaha TX4n - page 6

    TX6n/5n/4n Reference Manual 6 Controls and Connectors t [PRO TECTION] indicator When the protection system is acti ve, this indicator will light red. The protection circuit will operate in the follo wing situa- tions. • If the amplifier overheats and the output limiter operates The speaker output will be attenuated if the heat sink of the ampli? ...

  • Yamaha TX4n - page 7

    TX6n/5n/4n Reference Manual 7 Controls and Connectors !3 Encoders A, B When the display sho ws the attenuation meter , these encoders adjust the attenuation of channels A and B. If any other screen is displayed, encoder A mov es the cursor and encoder B modifies the parameter v alue. • Only encoder A can be operated if you’ re adjusting the at ...

  • Yamaha TX4n - page 8

    TX6n/5n/4n Reference Manual 8 Controls and Connectors @1 [SPEAKERS] jacks These are speaker output jacks. • Speakon connectors : Speakon type cable plugs (Neutrik NL4) can be connected here. • Five-way binding post connectors : Bare wires or Y plugs can be connected here. • The five-wa y binding post connectors and Speak on connectors are in ...

  • Yamaha TX4n - page 9

    TX6n/5n/4n Reference Manual 9 Controls and Connectors @4 [NETWORK] connector This is a 100B ASE-TX/10B ASE-T Ethernet connector . Y ou can connect this to a computer so that the amplifier can be mon- itored and controlled from Amp Editor. This also allo ws an external controller such as AMX or Crestron to be connected. •T o prev ent electromagne ...

  • Yamaha TX4n - page 10

    TX6n/5n/4n Reference Manual 10 Controls and Connectors ■ Remo ving and installing a card To remove and install a card, proceed as follo ws. 1. Make sur e that the power of the TXn is tur ned off. 2. Loosen the screws that fasten the slot, and r emov e the installed card. Keep the remo ved card in a safe place. 3. Align the two edges of the card t ...

  • Yamaha TX4n - page 11

    TX6n/5n/4n Reference Manual 11 Controls and Connectors To ensure adequate cooling air intake, the filter elements must be cleaned when they ha ve become clogged. F ollow the description below to clean each of the filter elements. 1. Make sur e that the power to the amplifier is tur ned off. 2. Disconnect the power cable fr om the A C outlet. 3. ...

  • Yamaha TX4n - page 12

    TX6n/5n/4n Reference Manual 12 Panel Operations ■ About the Displa y ■ Switching Screens By pressing a function b utton you can mov e to the screen indicated abo ve that b utton. By pressing the [HOME] button you can mov e to the HOME screen. By pressing the [EXIT] b utton you can mo ve to the screen one le vel abov e. ■ Editing the P aramete ...

  • Yamaha TX4n - page 13

    TX6n/5n/4n Reference Manual 13 Panel Operations Screen Structure METER SETTING • ANA INPUT VOL T AGE • SLOT INPUT VOL T AGE • SP OUTPUT VOL T AGE • SP OUTPUT POWER • SP OUTPUT IMPEDANCE • SLOT OUTPUT METER • THERMAL UTILITY • Device Setup • W ord Clock Setup • Information • Network Setup • LCD Setup • Front P anel Operatio ...

  • Yamaha TX4n - page 14

    TX6n/5n/4n Reference Manual 14 Panel Operations *Scene .......... The settings listed abov e, such as Standb y/P ow er-On or mute (with the e xception of UTILITY), are called a “scene”. By recalling a scene, the sav ed settings can be immediately applied to the amplifiers. Operations that can be P erformed fr om the P anel Category Subcategory ...

  • Yamaha TX4n - page 15

    TX6n/5n/4n Reference Manual 15 Panel Operations When an alert ev ent occurs related to the amplifier’ s audio, such as when an abnormality has occurred in the amplifier , an alert message will appear in the upper part of the display . At this time the [ALER T] indicator of each channel will also light. If Amp Editor is being used online, the al ...

  • Yamaha TX4n - page 16

    TX6n/5n/4n Reference Manual 16 Panel Operations This shows the input/output le vels of the audio signal, and the status of the power supply . As when y ou’ re in the HOME screen, y ou can use encoders A/B to adjust the attenuation of each channel. To access the METER screen, access the HOME scr een and pr ess the left-most function button (METER) ...

  • Yamaha TX4n - page 17

    TX6n/5n/4n Reference Manual 17 Panel Operations F or each meter type, this screen lets y ou specify various parameters f or alert detection, peak hold, and display units. ● Setting procedure 1. In the HOME screen, pr ess the left-most function b utton (METER) to access the METER screen. 2. Use the function buttons (PREV/NEXT) to access the scr ee ...

  • Yamaha TX4n - page 18

    TX6n/5n/4n Reference Manual 18 Panel Operations ● P arameter s that can be edited The parameters that can be edited will depend on the meter type. * The setting range will diff er depending on the meter type. Parameter Range Explanation Detect Enable ON/OFF Specifies whether aler t detection will be enabled or disab led. An aler t message will b ...

  • Yamaha TX4n - page 19

    TX6n/5n/4n Reference Manual 19 Panel Operations Here y ou can make settings for the amplifier itself and f or the network. ● Setting procedure 1. In the HOME screen, pr ess the second-fr om-left function button (UTILITY) to access the UTILITY scr een. 2. Use the function buttons (PREV/NEXT) to access the scr een f or the sub-category whose setti ...

  • Yamaha TX4n - page 20

    TX6n/5n/4n Reference Manual 20 Panel Operations ■ Wo rd Clock Setup Here you can select the master word clock that will synchronize digital audio signal processing. q Fs Indicates the current word clock frequenc y . w Int The status of the internal word clock. There are four possibilities: 44.1 kHz / 48 kHz / 88.2 kHz / 96 kHz. The default settin ...

  • Yamaha TX4n - page 21

    TX6n/5n/4n Reference Manual 21 Panel Operations ■ Inf ormation This screen sho ws information about the amplifier . This is only for display , and contains no editable parameters. ■ Netw ork Setup Here you can specify the IP address and other settings for using the amplifi er in a network. Parameter name Explanation Battery Indicates the stat ...

  • Yamaha TX4n - page 22

    TX6n/5n/4n Reference Manual 22 Panel Operations ■ LCD Setup Here you can adjust the display’ s contrast and backlight. ■ Fr ont P anel Operation Here you can turns panel operation lock on/of f. By locking panel operations you can pre vent unintended operation. • This setting restricts only panel operation of the amplifier itself; it does n ...

  • Yamaha TX4n - page 23

    TX6n/5n/4n Reference Manual 23 Panel Operations ● Setting the Lock 1. Use encoder A to move the cursor to the lock that y ou want to set, and use encoder B to change the setting. The parameter you switched will blink. 2. Press the [ENTER] b utton. The lock will be applied. ● Te mporarily defeating panel loc k Here’ s how you can temporarily d ...

  • Yamaha TX4n - page 24

    TX6n/5n/4n Reference Manual 24 Panel Operations ■ Misc Setup Here you can set the amplifier’ s internal clock, etc. Here y ou can make general settings for the amplifier in each category such as checking f or br oken connections, measuring the speaker impedance, and settings f or pr otection conditions. ● Setting procedure 1. In the HOME sc ...

  • Yamaha TX4n - page 25

    TX6n/5n/4n Reference Manual 25 Panel Operations 3. Use encoder A to move the cursor to the parameter that y ou want to edit, and encoder B to edit the parameter value. 4. If the parameter value is blinking, pr ess the [ENTER] button to confirm the v alue. Non-blinking parameter v alues are reflected by the amplifier in real time. ■ General Her ...

  • Yamaha TX4n - page 26

    TX6n/5n/4n Reference Manual 26 Panel Operations ● Input Redundancy Here you can make settings for a redundant connection (duplicate audio connections) that uses both the analog input signal and the digital (slot) input signal. If the digital input audio is interrupted by a brok en connection or other problem, the amplifi er can automatically swi ...

  • Yamaha TX4n - page 27

    TX6n/5n/4n Reference Manual 27 Panel Operations ■ Signal Chain Here you can make settings for checking whether the input or output has been interrupted by a brok en connection, etc. ● Analog Input Signal Chain/Slot Input Signal Chain Here you can make settings to specify ho w a pilot tone supplied from the external de vice will be detected to d ...

  • Yamaha TX4n - page 28

    TX6n/5n/4n Reference Manual 28 Panel Operations ■ Calibration Here you can detect the impedance v alue of the speak er connected to each channel, and apply the result to the alert settings (Signal Chain threshold v alues). • The impedance and output lev el cannot be detected when the output le vel is lo wered b y the attenuator . ● Calibrate ...

  • Yamaha TX4n - page 29

    TX6n/5n/4n Reference Manual 29 Panel Operations ■ Limiter Here you can specify the limiter conditions for the amplifier . ● V oltage Limiter These settings specify ho w the limiter will be controlled by the output v oltage. ● Po wer Limiter These settings specify ho w the limiter will be controlled by the output po wer . ● Limiter Gain Red ...

  • Yamaha TX4n - page 30

    TX6n/5n/4n Reference Manual 30 Panel Operations Here y ou can edit the components (equalizer , delay , crossov er , etc.) that use the internal DSP to perform audio sig- nal processing . This is displayed fr om the sub-category in the MENU scr een. •T o check details on the SIGNAL P A TH screen, we recommend that you use Amp Editor’ s Signal Pa ...

  • Yamaha TX4n - page 31

    TX6n/5n/4n Reference Manual 31 Panel Operations ● Setting procedure 1. In the HOME screen, pr ess the second-fr om-right function button (MENU) to access the MENU scr een. 2. Use encoder A or B to select “Signal Path, ” and press the [ENTER] button to access the SIGN AL P A TH screen. 3. Use encoder A or B to select the component that you wan ...

  • Yamaha TX4n - page 32

    TX6n/5n/4n Reference Manual 32 Panel Operations ■ Recalling library settings (Speaker Processor onl y) Y ou can sav e Speaker Processor component settings from Amp Editor as library data, and recall the settings from the ampli- fier’ s front panel. The library sa ves all parameters of the Speak er Processor components. • By default, the libr ...

  • Yamaha TX4n - page 33

    TX6n/5n/4n Reference Manual 33 Panel Operations ■ Slot Input Router Here you can specify the routing and gain from the slot input to each input channel. •T o specify the routing to the input channel, press the second-from-right function button (SELECT 1/SELECT 2) to select the input channel. ■ Input On/Off Here you can turn the input to the 4 ...

  • Yamaha TX4n - page 34

    TX6n/5n/4n Reference Manual 34 Panel Operations ■ 8Band Input EQ This is an eight-band parametric equalizer that boosts or cuts the signal at the specifi ed frequencies. F or each channel, you ca n make settings for each frequenc y band (B AND A–H). ■ Input Dela y Here you can specify a delay for the signal. Parameter name Range Explanation ...

  • Yamaha TX4n - page 35

    TX6n/5n/4n Reference Manual 35 Panel Operations ■ Oscillator Mix This is a mono-channel oscillator . It generates a sine wa ve, pink noise, or b urst noise. This can also mix the audio input signal and oscillator signal. ■ X-Over Input Level (Speaker Pr ocessor) This adjusts the input le vel to the crosso v er in a range of - ∞ – +10 dB. ? ...

  • Yamaha TX4n - page 36

    TX6n/5n/4n Reference Manual 36 Panel Operations ■ X-Over (Speaker Pr ocessor) Here you can apply a high-pass filter and lo w-pass filter to the signal, so that only a specifi c frequency re gion is allo wed to pass. Parameter name Range Explanation LPF F req 20.0 Hz–20 kHz Specifies the cutoff frequency of the low-pass filter . LPF T ype T ...

  • Yamaha TX4n - page 37

    TX6n/5n/4n Reference Manual 37 Panel Operations ■ Output Dela y (Speaker Pr ocessor) Here you can specify a delay for the signal. ■ 6Band Output EQ (Speaker Pr ocessor) This is a six-band parametric equalizer that boosts or cuts the signal at the specifi ed frequencies. F or each channel, you can make settings for each frequenc y band (B AND A ...

  • Yamaha TX4n - page 38

    TX6n/5n/4n Reference Manual 38 Panel Operations ● Filter types • PEQ This is a con ventional parametric equalizer . • L.SHELF (Low Shelving) W ithout attenuating the lo w frequencies, this filter applies a fixed amount of attenuation to the re gion abov e the cutof f frequency . 6 and 12 (dB/Oct) specify the amount of attenuation per octa v ...

  • Yamaha TX4n - page 39

    TX6n/5n/4n Reference Manual 39 Panel Operations ■ Limiter (Speaker Pr ocessor) This compresses signals exceeding the threshold at ∞ :1, pre venting signals higher than the threshold le vel from being output. ■ Output Router Here you can specify the routing for the slot output. F or each slot output channel, you can select from the follo wing ...

  • Yamaha TX4n - page 40

    TX6n/5n/4n Reference Manual 40 Panel Operations Here y ou can save parameter settings as a scene, and r ecall them from the fr ont panel or fr om Amp Editor. A scene contains various amplifier settings such as the Standby/P ower -On status, the parameter values of the com- ponents, and the threshold v alues of the alerts. 00 is the default setting ...

  • Yamaha TX4n - page 41

    TX6n/5n/4n Reference Manual 41 Panel Operations ■ Storing a scene Here’ s how to store the amplifier’ s settings in a scene 01–49. 1. In the HOME screen, pr ess the right-most function b utton (SCENE) to access the SCENE screen. 2. Use encoder A to select the scene number that you want to stor e. 3. Press the second function b utton fr om ...

  • Yamaha TX4n - page 42

    TX6n/5n/4n Reference Manual 42 Panel Operations ■ Editing a scene Here’ s how to edit the scene name or turn the protect setting on/of f for each scene 01–49. 1. In the HOME screen, pr ess the right-most function b utton (SCENE) to access the SCENE screen. 2. Use encoder A to select the scene number that you want to edit. 3. Press the second ...

  • Yamaha TX4n - page 43

    TX6n/5n/4n Reference Manual 43 Panel Operations Here’ s how to initialize the amplifier’ s internal memory . As desir ed, y ou can initialize two types of data. • User Data : All user data e xcept for the e vent log and the Speak er Processor library will be initialized. • Library : Only the Speaker Processor library will be initialized. ? ...

  • Yamaha TX4n - page 44

    TX6n/5n/4n Reference Manual 44 System Connection Examples Here is an example of multiple amplifiers connected in a daisy-chain via analog audio signals or digital audio sig- nals (e.g., AES/EBU). In the case of analog connection, daisy-chain the [THR U] jack and [IN] jack. In the case of digital connection (the standard AES-IO card), daisy-chain t ...

  • Yamaha TX4n - page 45

    TX6n/5n/4n Reference Manual 45 System Connection Examples ■ Thru-output f or digital connections For digital connections (the standard AES-IO card), the “thru” output from the [IN] jack to the [THR U] jack will be a signal that has passed through the b uf fer if the po wer is on, or a signal that bypasses the b uf fer if the po wer is of f. I ...

  • Yamaha TX4n - page 46

    TX6n/5n/4n Reference Manual 46 System Connection Examples By connecting both the analog audio signal and the digital audio signal, y ou can make a r edundant connection (duplicate audio connections). If the digital audio signal is interrupted by a problem such as a br oken connection, the system will switch to the analog audio signal. In order to e ...

  • Yamaha TX4n - page 47

    TX6n/5n/4n Reference Manual 47 System Connection Examples Y ou can use an interface card such as the MY16-ES64 to send and recei ve audio signals via an EtherSound net- work. From a single computer , y ou can use Amp Editor to monitor and control the amplifiers and use A VS-ESMonitor to make EtherSound settings. Howe ver on the amplifiers, the am ...

  • Yamaha TX4n - page 48

    TX6n/5n/4n Reference Manual 48 System Connection Examples Y ou can use an EtherSound interface unit such as the NAI48-ES to mak e a bridge connection from an EtherSound network to an AES/EBU signal. Bridge connections from EtherSound to AES/EB U Network switch Amp control TXn Amp Editor A VS-ESMonitor Computer Amp control Amp control Amp control TX ...

  • Yamaha TX4n - page 49

    TX6n/5n/4n Reference Manual 49 System Connection Examples Y ou can use an interface card such as the MY16-CII to send and recei ve audio signals via a CobraNet network. From Amp Editor, y ou can monitor and control the amplifiers, and make CobraNet settings f or the MY16-CII card. Howe ver on the amplifiers, the connections f or amplifier contro ...

  • Yamaha TX4n - page 50

    TX6n/5n/4n Reference Manual 50 System Connection Examples Y ou can use a CobraNet interface unit such as the NHB32-C to make a bridge connection fr om a CobraNet net- work to an AES/EBU signal. Bridge connections from CobraNet to AES/EB U Network switch Amp control TXn Amp Editor Computer Amp control Amp control Amp control TXn TXn IN CobraNet netw ...

  • Yamaha TX4n - page 51

    TX6n/5n/4n Reference Manual 51 Connecting Exter nal Contr ollers and Analog Devices Y ou can connect an Ethernet-compatible contr oller such as AMX or Crestr on to the amplifier’ s [NETWORK] connector , and remotely control the amplifier . When connecting a remote contr oller , you must specify the amplifier’ s Port No. The P ort No. setting ...

  • Yamaha TX4n - page 52

    TX6n/5n/4n Reference Manual 52 Connecting External Controllers and Analog Devices Use the included Euroblock plug (3P) to mak e connections to the [F A UL T OUTPUT] connector . 1. Loosen the terminal screws. • Use a slotted screwdriver with a blade appro ximately 2 mm wide. 2. Insert the cables. 3. Securely tighten the terminal scr ews. Pull the ...

  • Yamaha TX4n - page 53

    TX6n/5n/4n Reference Manual 53 Adjusting the Input/Output Levels On the TXn amplifiers, the gain / input sensitivity is adjusted by the input le vel bef ore A/D con version. The adjust- able gain range is the same f or the TX6n/TX5n/TX4n models. Since the maximum output is different f or each model, the settable range f or input sensitivity will d ...

  • Yamaha TX4n - page 54

    TX6n/5n/4n Reference Manual 54 Adjusting the Input/Output Levels ■ Basic level adjustment If we think of the TXn amplifier in a similar way as a con ventional analog amplifier , there are two parameters that determine the gain/le vel. • Gain / Input sensitivity: The input le vel before A/D con version is adjusted from the front panel MENU scr ...

  • Yamaha TX4n - page 55

    TX6n/5n/4n Reference Manual 55 Appendix Messages that may appear in the TXn’ s display and the appr opriate responses ar e listed below . Message List Message Explanation P anel Full lock ed! To prev ent unintended operation, panel operations hav e been lock ed by the panel loc k setting. To temporarily defeat panel loc k, hold down both the [HOM ...

  • Yamaha TX4n - page 56

    TX6n/5n/4n Reference Manual 56 Appendix The alert message display indicates the operational status of the unit or other alert inf ormation that you specified to display via Amp Editor. The f ollowing messages appear when certain malfunctions ar e suspected to hav e occurr ed. For details about alert messages, including the f ollowing messages, r e ...

  • Yamaha TX4n - page 57

    TX6n/5n/4n Reference Manual 57 Appendix Tr oubleshooting Symptom P ossible causes Response Po w er will not turn on, display will not light The power cab le is not con- nected properly . Connect the power cab le properly . The POWER s witch is not tur ned on. Tu rn the PO WER switch on. No sound from the speaker The cable is not connected prop- erl ...

  • Yamaha TX4n - page 58

    TX6n/5n/4n Reference Manual 58 Appendix Numerics 4x4 Matrix Mixer ........................................................... 33 6Band Output EQ ......................................................... 37 8Band Input EQ ............................................................ 34 A About the documentation ....................................... ...

  • Yamaha TX4n - page 59

    TX6n/5n/4n Reference Manual 59 Appendix L L.SHELF ....................................................................... 38 Label ............................................................................. 19 Last Memory Resume ................................................... 23 LCD Setup ...................................................... ...

  • Yamaha TX4n - page 60

    U .R.G., Pro Audio & Digital Musical Instrument Division, Y amaha Corporation © 2009 Y amaha Cor poration 909-PO-D0 ...

Fabbricante Yamaha Categoria Stereo Amplifier

I documenti che otteniamo dal fabbricante del dispositivoYamaha TX4n possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Yamaha
- manuali per l’uso TX4n
- schede prodotto Yamaha
- opuscoli
- o etichette energetiche Yamaha TX4n
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Yamaha TX4n.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Yamaha TX4n, manuali di manutenzione, brevi manuali o manuali utente Yamaha TX4n. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Yamaha TX4n.

Manuali per l’uso simili

Manuale completo del dispositivo Yamaha TX4n, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Yamaha TX4n dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Yamaha TX4n.

Il manuale per l’uso completo Yamaha, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Yamaha TX4n - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Yamaha TX4n, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Yamaha TX4n che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Yamaha TX4n - che ci dovrebbe aiutare nei primi passi durante l'uso Yamaha TX4n
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Yamaha TX4n
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Yamaha TX4n in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Yamaha TX4n?

Utilizza il modulo sottostante

Se non hai risolto il problema con Yamaha TX4n con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Yamaha TX4n è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)