Manuale per l’uso Vision Fitness ST250

16 pagine 2.61 mb
Scarica

Vai alla pagina of 16

Summary
  • Vision Fitness ST250 - page 1

    Assembly Guide ST250 LEG PRESS ...

  • Vision Fitness ST250 - page 2

    2 T o avoid possible damage to this Leg Press, please follow these assembly steps in the correct order . Before proceeding, find yo ur new Leg Press’ serial number located on the back of the base tube (1b), and enter here: Refer to this number when calling for ser vice, and enter this serial number on your W arranty Card and in your own records. ...

  • Vision Fitness ST250 - page 3

    3 5 STEP 3 STEP 2 STEP 4 STEP 6 STEP 7 STEP 8 STEP 1 STEP ...

  • Vision Fitness ST250 - page 4

    4 19mm Wrench 6mm L-Shaped Wrench (2) TOOLS & P AR TS INCLUDED P AR TS BOX Color-coded Hardware Bags Owner’ s Guide Assembly Guide W arranty Card 10mm/17mm Wrench 4mm L-Shaped Wrench ...

  • Vision Fitness ST250 - page 5

    5 ORANGE BAG BLUE BAG HARDW ARE INCLUDED M10 x 1.5P Nut Quantity: 12 10.5 x 18 x 2T Flat W asher Quantity: 16 M10 x 1.5P x 60L Carriage Bolt Quantity: 2 SW10.2 x 18.4 x 2.5T Spring W asher Quantity: 8 M10 x 1.5P x 100L Bolt Quantity: 4 M10 x 1.5P Nut Quantity: 3 M10 x 1.5P x 30L Bolt Quantity: 8 M10 x 1.5P x 105L Bolt Quantity: 1 Pull Pin Quantity: ...

  • Vision Fitness ST250 - page 6

    6 PINK BAG GREEN BAG HARDW ARE INCLUDED 10.5 x 18 x 2T Flat W asher Quantity: 2 M10 x 1.5P Nut Quantity: 2 M6 x 1P x 15L Bolt Quantity: 3 90mm Shaft Quantity: 1 10.5 x 30 x 2T Flat W asher Quantity: 2 165mm Shaft Quantity: 1 SW6.1 x 12.2 x 1.5T Spring W asher Quantity: 3 6.4 x 14 x 1T Flat W asher Quantity: 3 SW10.2 x 18.4 x 2.5T Spring W asher Qua ...

  • Vision Fitness ST250 - page 7

    7 BLACK BAG 15x33L Shoulder Bolt Quantity: 1 U Bracket Quantity: 1 M12 Slotted Bolt Quantity: 1 M10 x 1.5P Nut Quantity: 1 10.5 x 18 x 2T Flat W asher Quantity: 1 SW10.2 x 18.4 x 2.5T Spring W asher Quantity: 1 HARDW ARE INCLUDED ...

  • Vision Fitness ST250 - page 8

    8 1 STEP • If you aren’t adding any weight plates to the stack, skip this step and proceed to Step 2. • Y our unit is equipped to handle 21-ten pound plates (20 plates and the header plate). If you are adding plates to the stack after it has been in use, proceed as follows: Loosen the nuts, attached to the bolts (5g) with a 10mm wrench and a ...

  • Vision Fitness ST250 - page 9

    9 1b 1a 1d 1c 1e 1e 2 STEP • Attach the connecting brace (1a) to the empty holes on the left floor support of the base unit ( ST200 ). Connect with two carriage bolts (M10x1.5Px60L), two fl at (10. 5x18x2 T) & s p r i n g (SW10.2x18.4x2.5T) washers, and two nuts (M10x1.5P). Attach the opposite end of the connecting brace to the main floor sup ...

  • Vision Fitness ST250 - page 10

    10 3 STEP • Lay the seatback (2a) face down. Mate the seatback support (2b) to 2a. Make sure the holes of 2b are pointing up towards the top of the seatback. Securely fasten four bolts (M10x1.5Px30L) into the seatback using a 6mm L-shaped wrench. Thread the pull pin partially into the opening of 1b. Guide the seatback into the oval opening at the ...

  • Vision Fitness ST250 - page 11

    11 4 STEP • Insert the lever ar m (3a) into the triangular structure at the front of 1b. When the holes are lined up, insert the 90mm shaft along with a flat (17 x25x 1.5 T) washer through the lower end of 3a and fasten with a flat (10.5x30x2T) washer and a bolt (M10x1.5Px20L). Tig ht en fi rm ly usi ng two 6mm L-shaped wrenches. • Insert the f ...

  • Vision Fitness ST250 - page 12

    12 5 STEP • If you already have the base unit assembled with cable #2 and are adding the leg press to it, follow this instruction, other wise proceed to Step 6: Unscrew the nuts and bolt that attaches cable #2 to the rear termination tube (6b of base unit), using a 19mm wrench. Unscrew the nuts from the slotted bolt. P u l l the cable out through ...

  • Vision Fitness ST250 - page 13

    13 6 STEP • Attach the pulley structure (U) to the bottom rear floor support of the base unit with three bolts (M6x1Px15L), three f l a t (6.4x14x1T), and three spring (SW6.1x12.2x1.5T) washers. Tighten with a 4mm L-shaped wrench. • Slide pulley structure (Q) through the back side of the rear vertical suppor t (base unit) and fasten securely wi ...

  • Vision Fitness ST250 - page 14

    14 7 STEP • Begin routing cable #6 with the end opposite the steel ball end. Feed the cable over pulley R, under S, around T , and under U. Unscrew the nut from the slotted bolt (M12). With the threads of the bolt facing up, slide cable #6 through it and reattach the nut. Thread the bolt into the post of pulley V , just enough so the cable won’ ...

  • Vision Fitness ST250 - page 15

    15 8 STEP • Attach the decals according to the diagram below . DECALS PINCH POINT SAFETY DECAL PLACEMENT ...

  • Vision Fitness ST250 - page 16

    500 South CP Avenue • P .O. Box 280 • Lake Mills. WI 53551 toll free 800.335.4348 • phone 920.648.4090 • fax 920.648.3373 www .visionfitness.com © 2005 Vision Fitness. All Rights Reserved. 10.05 AG18.38PRD REV2 starts vision with a it all ...

Fabbricante Vision Fitness Categoria Home Gym

I documenti che otteniamo dal fabbricante del dispositivoVision Fitness ST250 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Vision Fitness
- manuali per l’uso ST250
- schede prodotto Vision Fitness
- opuscoli
- o etichette energetiche Vision Fitness ST250
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Vision Fitness ST250.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Vision Fitness ST250, manuali di manutenzione, brevi manuali o manuali utente Vision Fitness ST250. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Vision Fitness ST250.

Manuali per l’uso simili

Manuale completo del dispositivo Vision Fitness ST250, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Vision Fitness ST250 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Vision Fitness ST250.

Il manuale per l’uso completo Vision Fitness, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Vision Fitness ST250 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Vision Fitness ST250, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Vision Fitness ST250 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Vision Fitness ST250 - che ci dovrebbe aiutare nei primi passi durante l'uso Vision Fitness ST250
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Vision Fitness ST250
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Vision Fitness ST250 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Vision Fitness ST250?

Utilizza il modulo sottostante

Se non hai risolto il problema con Vision Fitness ST250 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Vision Fitness ST250 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Commenti (0)