Italiano dropdown-ico

Manuale per l’uso Siemens RDG400

42 pagine 1.14 mb
Scarica

Vai alla pagina of 42

Summary
  • Siemens RDG400 - page 1

    s Room Thermost at with Display , for V A V RDG400 Basic Document ation Edition: 1.0 CE1P3182en 28 May 2009 Building Technologies ...

  • Siemens RDG400 - page 2

    2 / 42 Siemens RDG100, RDG100T, RDG11 0, RDG140, RDG160 Basic Documentation CE1P3182en Building Technologies Table of contents 28 May 2009 T able of content s 1 About this doc ument ......................................................................................... 3 1.1 Revision hi story ...................................................... ...

  • Siemens RDG400 - page 3

    3 / 42 Siemens RDG100, RDG100T, RDG11 0, RDG140, RDG160 Basic Documentation CE1P3182en Building Technologies About this document 28 May 2009 1 About this document 1.1 Revision history Edition Date Changes Section Pages 1.0 May 2009 First edition 1.2 Reference document s Ref. Document title T ype of document Document No. [1] W all-mounted room therm ...

  • Siemens RDG400 - page 4

    4 / 42 Siemens RDG100…/RDG110…/RDG140.../RDG1 60… Basic Documentation CE1P3182en Building Technologies About this document 28 May 2009 1.3.3 Document use / request to the reader Before using our product s, it is important that you read the document s supplied with or ordered at the same time as the p roducts (equipment, appli cations, tools e ...

  • Siemens RDG400 - page 5

    5 / 42 Siemens RDG100, RDG100T, RDG11 0, RDG140, RDG160 Basic Documentation CE1P3182en Building Technologies Summary 28 May 2009 2 Summary 2.1 Brief description • Single-duct system • Single-duct system with electrical heater • Single-duct system and radiator / floor heating • Single-duct system with heating / cooling coil • Two multifunc ...

  • Siemens RDG400 - page 6

    6 / 42 Siemens RDG100…/RDG110…/RDG140.../RDG1 60… Basic Documentation CE1P3182en Building Technologies Summary 28 May 2009 2.3 Equipment combinations Description Product no. Dat a Sheet Cable temperature senso r QAH1 1.1 1840 Room temperature sensor QAA32 1747 Condensation detector / extension module QXA2000 / AQX2000 1542 Electrical actuator ...

  • Siemens RDG400 - page 7

    7 / 42 Siemens RDG100, RDG100T, RDG11 0, RDG140, RDG160 Basic Documentation CE1P3182en Building Technologies Use 28 May 2009 Electrical actuator , 3-position ( for radiator valve ) SSA81... 4893 Electrical actuator , 3-position ( for small valve 2 , 5 mm ) SSP81… 4864 Electrical actuator , 3-position ( for small valve 5 , 5 mm ) SSB81... 4891 Ele ...

  • Siemens RDG400 - page 8

    8 / 42 Siemens RDG100…/RDG110…/RDG140.../RDG1 60… Basic Documentation CE1P3182en Building Technologies Functions 28 May 2009 4 Functions 4.1 T emperature control Setting of the control para meters (P01 etc., mentioned throughout the document) is described in section 4.12. The thermost at acqui res the room temperat ure via built-in sensor , e ...

  • Siemens RDG400 - page 9

    9 / 42 Siemens RDG100, RDG100T, RDG11 0, RDG140, RDG160 Basic Documentation CE1P3182en Building Technologies Functions 28 May 2009 4.2 Operating modes Select the thermostat' s operating mode via operating mode button on the thermostat or operating mode input (e.g. keycard occupancy se nsor , when X1, X2, or D1 set to 3 (P38, P40, P42). A corr ...

  • Siemens RDG400 - page 10

    10 / 42 Siemens RDG100…/RDG110…/RDG140.../RDG1 60… Basic Documentation CE1P3182en Building Technologies Functions 28 May 2009 4.3 Setpoint s The setpoint in Comfort mode ca n be adjusted via the rotary knob . For Energy Saving purposes, the setpoi nt adjusting range can be limited to minimum (P09) and maximum (P10). • If the minimum limit P ...

  • Siemens RDG400 - page 11

    11 / 42 Siemens RDG100, RDG100T, RDG11 0, RDG140, RDG160 Basic Documentation CE1P3182en Building Technologies Functions 28 May 2009 4.4 Setpoint s and sequence In single-duct changeove r applications the Comfort setpoints for heating and cooling sequence are the same (w). In applications with electrical heater , radiat or or heating / cooling coil ...

  • Siemens RDG400 - page 12

    12 / 42 Siemens RDG100…/RDG110…/RDG140.../RDG1 60… Basic Documentation CE1P3182en Building Technologies Functions 28 May 2009 Comfort mode Energy Saving mode Application Heating mode Cooling mode Heating mode Cooling mode Single duct with heating / cooling coil Protection mode Heating mode Cooling mode W=Setpoint in Comfort mode W HeatEco/Pro ...

  • Siemens RDG400 - page 13

    13 / 42 Siemens RDG100, RDG100T, RDG11 0, RDG140, RDG160 Basic Documentation CE1P3182en Building Technologies Functions 28 May 2009 4.5 Applications overview The thermostat supp orts the following applications, which can be configured via DIP s w itches at the rear of the unit. The control output for the damper actuator is either DC 0…10 V (facto ...

  • Siemens RDG400 - page 14

    14 / 42 Siemens RDG100…/RDG110…/RDG140.../RDG1 60… Basic Documentation CE1P3182en Building Technologies Functions 28 May 2009 4.6 Additional features The output signals DC 0…10V can b e in verted by means of DIP switch 4 (see section 4.7.3). T o ensure a minimum or maximum supply air volume, the outpu t signal for the air flow (DC 0...10V o ...

  • Siemens RDG400 - page 15

    15 / 42 Siemens RDG100, RDG100T, RDG11 0, RDG140, RDG160 Basic Documentation CE1P3182en Building Technologies Functions 28 May 2009 30 76Z 03 X2 M T X2 M QAH 11. 1 T °C Contact op en  heating mode Contact cl osed  cooling mode The sensor or switch can be con nected to the input terminal X2 (factory setting) or X1 or D1 (switch only), dependi ...

  • Siemens RDG400 - page 16

    16 / 42 Siemens RDG100…/RDG110…/RDG140.../RDG1 60… Basic Documentation CE1P3182en Building Technologies Functions 28 May 2009 If the button lock function is enabled by parameter P1 4, then the buttons will be locked or unlocked by pressing the rig ht button for 3 sec. If “Auto lock” is configured, then the thermost at will automatically l ...

  • Siemens RDG400 - page 17

    17 / 42 Siemens RDG100, RDG100T, RDG11 0, RDG140, RDG160 Basic Documentation CE1P3182en Building Technologies Functions 28 May 2009 4.7 Control sequences 4.7.1 Applications and sequences Application V A V Sequen ces Single duct h ( ), c ( / ) Single duct & electrical heater el.h + c (  / ) Single duct & radiator rad + c ( r / ), Sin ...

  • Siemens RDG400 - page 18

    18 / 42 Siemens RDG100…/RDG110…/RDG140.../RDG1 60… Basic Documentation CE1P3182en Building Technologies Functions 28 May 2009 4.7.3 Control output s overview (setting via DIP 4 / 5 and parameters P46 / P47) Control outputs Application  ON/OFF (2-position) Modulating PWM (2-position) Modulating 3-position Modulating DC 0 … 10 V Single duc ...

  • Siemens RDG400 - page 19

    19 / 42 Siemens RDG100, RDG100T, RDG11 0, RDG140, RDG160 Basic Documentation CE1P3182en Building Technologies Functions 28 May 2009 4.7.4 Single duct In single duct applications, the controlle r controls an actuator (valve, damper , V A V system, etc) – in heating/cooling mode with changeover (automatic or manual), – heating only mode, – or c ...

  • Siemens RDG400 - page 20

    20 / 42 Siemens RDG100…/RDG110…/RDG140.../RDG1 60… Basic Documentation CE1P3182en Building Technologies Functions 28 May 2009 4.7.5 Single duct with electrical heater In single duct applications with electrical heater , the thermostat controls a valve plus an auxiliary electrical heater . Parameter P01 is not available. The output signal for ...

  • Siemens RDG400 - page 21

    21 / 42 Siemens RDG100, RDG100T, RDG11 0, RDG140, RDG160 Basic Documentation CE1P3182en Building Technologies Functions 28 May 2009 4.7.6 Single duct with radiat or or floor heating In single duct applications with radiator or floor heating, the thermost at controls a valve plus an auxiliary electrical heat er . Parameter P01 is not available. The ...

  • Siemens RDG400 - page 22

    22 / 42 Siemens RDG100…/RDG110…/RDG140.../RDG1 60… Basic Documentation CE1P3182en Building Technologies Functions 28 May 2009 4.7.7 Single duct with heating / cooling coil In single duct applications with heating / cooling coil, the co ntroller controls an actuator (damper , V A V system, etc.) pl us a reheating / cooling water coil. The outp ...

  • Siemens RDG400 - page 23

    23 / 42 Siemens RDG100, RDG100T, RDG11 0, RDG140, RDG160 Basic Documentation CE1P3182en Building Technologies Functions 28 May 2009 4.8 Control output s Different control output signals are av ailable dependi ng on the configuration of thermostat via DIP switches 4 & 5, and parameters P46 & P47. Contro l output Product No. Modulating DC 0 ? ...

  • Siemens RDG400 - page 24

    24 / 42 Siemens RDG100…/RDG110…/RDG140.../RDG1 60… Basic Documentation CE1P3182en Building Technologies Functions 28 May 2009 4.8.2 Control output for electrical he ater , radiator and heating / cooling coil The valve receives an OPEN/ON comma nd via control output Y1 1. When the acquired room temperature is below “setpoint” (he ating mod ...

  • Siemens RDG400 - page 25

    25 / 42 Siemens RDG100, RDG100T, RDG11 0, RDG140, RDG160 Basic Documentation CE1P3182en Building Technologies Functions 28 May 2009 Output Y1 provides the OPEN command, and Y2 the CLOSE command to the 3- position actuator . The factory setting for the actuator runtime is 150 secon ds. It can be adjusted via parameter P44 (Y1 and Y2). The parameter ...

  • Siemens RDG400 - page 26

    26 / 42 Siemens RDG100…/RDG110…/RDG140.../RDG1 60… Basic Documentation CE1P3182en Building Technologies Functions 28 May 2009 4.9 Multifunctional input, Digit al input The thermostat of fers two multifunctional inputs X1 and X2 and a digital input D1. A sensor of type NTC like QAH1 1.1 (AI, analog input) or a switch (DI, digital input) can be ...

  • Siemens RDG400 - page 27

    27 / 42 Siemens RDG100, RDG100T, RDG11 0, RDG140, RDG160 Basic Documentation CE1P3182en Building Technologies Functions 28 May 2009 4.10 Handling of fault s When the room temperature is out side the measuring range, i.e. above 49 °C or below 0 °C, the limiting temperatures flash, e.g. “0 °C” or “49 °C”. The heating output is energized i ...

  • Siemens RDG400 - page 28

    28 / 42 Siemens RDG100…/RDG110…/RDG140.../RDG1 60… Basic Documentation CE1P3182en Building Technologies Functions 28 May 2009 4.12 Control p arameters A number of control p arameters can be r eadjusted to optimize control performance. These parameters can also be set during operation without opening the unit. In the event of a power failure, ...

  • Siemens RDG400 - page 29

    29 / 42 Siemens RDG100, RDG100T, RDG11 0, RDG140, RDG160 Basic Documentation CE1P3182en Building Technologies Functions 28 May 2009 4.12.1 Parameters Service level Parame ter Name Factory setting Range RDG400 Service lev el P01 Control sequence W hen 2-pipe / 2-stage: 1 = Cooling on ly W hen 4-pipe: 4 = H and C 0 = Heating only 1 = Cooling only 2 = ...

  • Siemens RDG400 - page 30

    30 / 42 Siemens RDG100…/RDG110…/RDG140.../RDG1 60… Basic Documentation CE1P3182en Building Technologies Functions 28 May 2009 4.12.2 Parameters Expert level, diagnostics & test Para meter Name Factory setting Range RDG400 Ex p ert lev el P30 P -band / Switc hing different ial in heating m ode 2 K 0.5 … 6 K  P31 P -band / Switc hing d ...

  • Siemens RDG400 - page 31

    31 / 42 Siemens RDG100, RDG100T, RDG11 0, RDG140, RDG160 Basic Documentation CE1P3182en Building Technologies Functions 28 May 2009 Parameter Name Factory sett ing Range RDG400 Dia g nostics & test d01 Appli cati on type Diagnost ics 0:= --- (No appli cation) 1:= Single-d uct 2:= Single-d uct with el . heater 3:= Single-d uct with radi ator 4:= ...

  • Siemens RDG400 - page 32

    32 / 42 Siemens RDG100…/RDG110…/RDG140.../RDG1 60… Basic Documentation CE1P3182en Building Technologies Handling 28 May 2009 5 Handling 5.1 Mounting and inst allation Do not mount on a wall in niches or bookshelve s, behind curtains, above or near heat sources, or exposed to direct sola r radiation. Mo unt about 1.5 m above the floor . • Th ...

  • Siemens RDG400 - page 33

    33 / 42 Siemens RDG100, RDG100T, RDG11 0, RDG140, RDG160 Basic Documentation CE1P3182en Building Technologies Handling 28 May 2009 5.2 Operation See also the operating instructions B3181 encl osed with the thermostat. Layout 1 Operating mode button / Esc 2 Protection mode and OK 3 Rot ary knob for setpoint and parameter adjustment • When the ther ...

  • Siemens RDG400 - page 34

    34 / 42 Siemens RDG100…/RDG110…/RDG140.../RDG1 60… Basic Documentation CE1P3182en Building Technologies Handling 28 May 2009 1 2 4 5 6 6 7 8 9 10 11 12 13 14 16 3 15 17 # Symbol Description # Symbol Description 1 Heating mode 10 Confirmation of parameters 2 Electrical heater active 11 Degrees Celsius Degrees Fahrenheit 3 Cooling mode 12 Digit ...

  • Siemens RDG400 - page 35

    35 / 42 Siemens RDG100, RDG100T, RDG11 0, RDG140, RDG160 Basic Documentation CE1P3182en Building Technologies Engineering 28 May 2009 6 Engineering 6.1 Connection terminals G X1 M X2 D1 GND G0 SEL V G , G0 Operating voltage AC 24 V Y10/G0 Control output for DC 0…10 V a ctuator Y1/G , Y2/G Control output for 2-p osition, PWM or 3-position actuator ...

  • Siemens RDG400 - page 36

    36 / 42 Siemens RDG100…/RDG110…/RDG140.../RDG1 60… Basic Documentation CE1P3182en Building Technologies Engineering 28 May 2009 6.2 Connection diagrams For details concerning connection of per ipheral devices and setting of the DIP switches please refer to the mounting in structions, document M3182. Application: Single-duct V 1 S3 V 1 V1 DC 0 ...

  • Siemens RDG400 - page 37

    37 / 42 Siemens RDG100, RDG100T, RDG11 0, RDG140, RDG160 Basic Documentation CE1P3182en Building Technologies Mechanical design 28 May 2009 7 Mechanical design 7.1 General The room thermost at consists of 2 p arts: • Plastic housing which accommod ates the electronics, the operating elements and the temperature sensor • Mounting plate with the ...

  • Siemens RDG400 - page 38

    38 / 42 Siemens RDG100…/RDG110…/RDG140.../RDG1 60… Basic Documentation CE1P3182en Building Technologies Technical data 28 May 2009 8 T echnical dat a Operating voltage SELV AC 24 V ± 20% Frequency 50/60 Hz Power consumption Max. 2 VA Control output Y10-G0 Resolution Current DC 0…10 V 39 mV Max. ± 1 mA Control output Y1, Y2-G Rating AC 24 ...

  • Siemens RDG400 - page 39

    39 / 42 Siemens RDG100, RDG100T, RDG11 0, RDG140, RDG160 Basic Documentation CE1P3182en Building Technologies Technical data 28 May 2009 Operation Climatic conditions Tempera ture Humidity As per IEC 721-3-3 Class 3K5 0 ...50 °C < 95% r.h. Transport Climatic conditions Tempera ture Humidity Mechanical conditions As per IEC 721-3-2 Class 2K3 − ...

  • Siemens RDG400 - page 40

    40 / 42 Siemens RDG100…/RDG110…/RDG140.../RDG1 60… Basic Documentation CE1P3182en Building Technologies Index 28 May 2009 Index 3 3-position cont rol sig nal ......................................... 23 3-position for air fl ow ............................................. 23 A Absence ......................................................... ...

  • Siemens RDG400 - page 41

    41 / 42 Siemens RDG100, RDG100T, RDG110, RDG140, RD G160 Basic Documentation CE1P3182en Building Technologies 28 May 2009 ...

  • Siemens RDG400 - page 42

    42 / 42 Siemens RDG100…/RDG110…/RDG140.../RDG1 60… Basic Documentation CE1P3182en Building Technologies 28 May 2009 Siemens Switzerland Ltd Building T echnologies Division International Headquarters Gubelstrasse 22 CH-6301 Zug T el. +41 41- 724 24 24 Fax +41 41-724 35 22 www .buildin g technolo g ies.siemens.com © 2009 Siemens Switzerland Lt ...

Fabbricante Siemens Categoria Cassette Player

I documenti che otteniamo dal fabbricante del dispositivoSiemens RDG400 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Siemens
- manuali per l’uso RDG400
- schede prodotto Siemens
- opuscoli
- o etichette energetiche Siemens RDG400
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Siemens RDG400.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Siemens RDG400, manuali di manutenzione, brevi manuali o manuali utente Siemens RDG400. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Siemens RDG400.

Manuali per l’uso simili

Manuale completo del dispositivo Siemens RDG400, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Siemens RDG400 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Siemens RDG400.

Il manuale per l’uso completo Siemens, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Siemens RDG400 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Siemens RDG400, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Siemens RDG400 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Siemens RDG400 - che ci dovrebbe aiutare nei primi passi durante l'uso Siemens RDG400
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Siemens RDG400
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Siemens RDG400 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Siemens RDG400?

Utilizza il modulo sottostante

Se non hai risolto il problema con Siemens RDG400 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Siemens RDG400 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)