Italiano dropdown-ico

Manuale per l’uso Napco Security Technologies XP-600

16 pagine 0.13 mb
Scarica

Vai alla pagina of 16

Summary
  • Napco Security Technologies XP-600 - page 1

    Using Your XP-600 Securit y System ARMED READY SYSTEM ü FIRE AC ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 NAPCO Oi218a.pub page 1 Thursday, December 18, 1997 18:29 ...

  • Napco Security Technologies XP-600 - page 2

    Introduction Congratulations on your purchase of an advanced NAPCO EXPRESS XP-600 Security System. Meticulously developed by a leading manufacturer of state-of-the-art security products, this system will provide you with unprecedented peace-of-mind & incorporates some of the most sophisticated features available today. Above all, it has been de ...

  • Napco Security Technologies XP-600 - page 3

    3 1 Bell / Battery Test Test your bell or siren by pressing A followed by 1 .This will cause the bell, or siren to sound for 2 seconds and also initiate a test of the battery . 2 Central Station Communication Test (This test should only be performed on weekends or at a time designated by your alarm company) 1. Notify Central Station of the impendin ...

  • Napco Security Technologies XP-600 - page 4

    ARMED READY SYSTEM ü FIRE AC ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 4 Keypad Controls and Indicators Ready Light will light when all zones are secure and system is ready to be Armed. AC Light will light to indicate that AC Power is present. Fire Alarm Light will flash and the Keypad sounder will beep when system is in a Fire Alarm Condition (Se ...

  • Napco Security Technologies XP-600 - page 5

    Arming Your System When Leaving 1 Before arming your system, make sure the Green Ready light is ON. This indicates that all of your prot- ective zones are secure. If any zones are open, the corresponding Zone light will be ON. Secure these zones before proceeding. If any zones cannot be secured, see Bypassing Zones below. 2 Enter your user code. Th ...

  • Napco Security Technologies XP-600 - page 6

    Protecting Yourself While at Home 1 Before arming your system, make sure the Green Ready light is ON. This indicates that all of your protective zones are secure. If any zones are open, the corresponding Zone light will be ON. Secure those zones before proceeding. 2 Enter your user code. The Green Ready light will go out, and the Red Armed light wi ...

  • Napco Security Technologies XP-600 - page 7

    Emergency Buttons The three sets of emergency buttons, if programmed, are always active whether the system is armed or disarmed. Discuss these Buttons with your installer. The emergency signal will only be activated when the two respective buttons are pressed at the same time. Fire Alarm : Simultaneously press E + E to sound a fire alarm, and to al ...

  • Napco Security Technologies XP-600 - page 8

    Disarming Your System when Returning 1 Enter your premises through the Entry/Exit door. The keypad will sound a steady tone to remind you to disarm the system before your Entry Delay time expires. 2 Enter your user code. The Red Armed light will go out, indicating that the system has been disarmed. Note: If you make a mistake entering your code, pr ...

  • Napco Security Technologies XP-600 - page 9

    Preparing a Fire Escape Plan Even with the most advanced fire alarm system, adequate protection requires an escape plan. To prepare your plan, draw floor plans of your building. (space is provided on the next page) Show two exits - a front or back door and a window from each room. (Make sure each window works. You may need a special fire-escape lad ...

  • Napco Security Technologies XP-600 - page 10

    10 Fire Protection Floorplan Draw a plan of your premises below. Oi218a.pub page 10 Thursday, December 18, 1997 18:29 ...

  • Napco Security Technologies XP-600 - page 11

    Special Functions A By pressing A followed by the appropriate key, (do not press simultaneously) these special functions and features can be enabled: A0 Easy Arm (when system is disarmed) The Easy Arm feature allows the system to be armed by pressing A followed by 0 . This will allow the easy arming of the system by someone who is not a regular sys ...

  • Napco Security Technologies XP-600 - page 12

    The XP600 is constantly monitoring its own components, as well as all critical services, such as AC Power and the Telephone line, to insure that it is always ready to provide the protection for which it was designed. When a system trouble does occur, it will caution you by lighting the yellow ü ü SYSTEM light and beeping the keypad buzzer. If you ...

  • Napco Security Technologies XP-600 - page 13

    13 ü ü System Troubles Keypad Beeps or ü ü SYSTEM Flashes Zone light ON System Trouble Condition Action 2 Beeps 2 Fire Trouble A problem has been detected in the Fire Circuit. Call installing company for service. 2 Beeps 3 Wireless Receiver Trouble A problem has been detected with the wireless receiver. Call installing company for service. 2 Be ...

  • Napco Security Technologies XP-600 - page 14

    Your Installer has assigned a User 1 Code which may be used to not only Arm and Disarm the system, but also to enter the User Program Mode, where you can program other user codes. The following explains how you will use this code to program or erase additional user codes. Entering the User Program Mode Press A followed by 8 and then enter the User ...

  • Napco Security Technologies XP-600 - page 15

    Ambush Code - In the event that you are forced by an intruder to dis- arm your system, this special code can be used to disarm the system, and simultaneously send a silent alarm to Central Station. If your sys- tem has the Ambush feature enabled, the code assigned as the User 6 code will function as your Ambush Code Arming / Disarming - Turning the ...

  • Napco Security Technologies XP-600 - page 16

    NAPCO LIMITED WARRANTY THE FOLLOWING STATEMENT IS REQUIRED BY THE FCC . This equipment generates and uses radio-frequency energy and, if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with ...

Fabbricante Napco Security Technologies Categoria Home Security System

I documenti che otteniamo dal fabbricante del dispositivoNapco Security Technologies XP-600 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Napco Security Technologies
- manuali per l’uso XP-600
- schede prodotto Napco Security Technologies
- opuscoli
- o etichette energetiche Napco Security Technologies XP-600
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Napco Security Technologies XP-600.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Napco Security Technologies XP-600, manuali di manutenzione, brevi manuali o manuali utente Napco Security Technologies XP-600. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Napco Security Technologies XP-600.

Manuali per l’uso simili

Manuale completo del dispositivo Napco Security Technologies XP-600, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Napco Security Technologies XP-600 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Napco Security Technologies XP-600.

Il manuale per l’uso completo Napco Security Technologies, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Napco Security Technologies XP-600 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Napco Security Technologies XP-600, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Napco Security Technologies XP-600 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Napco Security Technologies XP-600 - che ci dovrebbe aiutare nei primi passi durante l'uso Napco Security Technologies XP-600
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Napco Security Technologies XP-600
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Napco Security Technologies XP-600 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Napco Security Technologies XP-600?

Utilizza il modulo sottostante

Se non hai risolto il problema con Napco Security Technologies XP-600 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Napco Security Technologies XP-600 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (1)

Noel

Bonjour Comment avoir la doc en Francais merci