-
Makita 6202DW - page 1
Cordless Driver Drill Battery Cartridge 9101 I9101A Voltage Equipped with Electric Brake MODEL 62021) MODEL 6202DW With Fast Charger MODEL 6202DWG With Fast Charger Model DC1201 Fast Charger Input output Charging time INSTRUCTION MANUAL 9.6 V SPEC IF I CAT I 0 N S ~ A.C. only 50 Hz - 60 Hz D.C. 7.2 V - 12 V 1 Hr. Model 6202D ~___________ ~ Dimensio ...
-
Makita 6202DW - page 2
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. ...
-
Makita 6202DW - page 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch is OFF when plugging in. 16. EXTENSION CORDS. Make sure your extension cord is in good condition. When using ...
-
Makita 6202DW - page 4
VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user - as well as damage to the tool. If in doubt, DO NOT PLUG IN T ...
-
Makita 6202DW - page 5
IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRIDGE 1. 2. 3. 4. 5. 6. 7. 8. 9. IO. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using batter ...
-
Makita 6202DW - page 6
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) 2. Do not attempt to use a step-up transformer, an engine generator or DC power 3. Do not allow anything to cover or clog the charger vents. 4. Always cover the battery terminals with the battery cover when the batte ...
-
Makita 6202DW - page 7
Installing or removing battery cartridge .Always switch off the tool before insertion or removal or the battery cartridge. .To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the tool. .To insert the battery cartridge, align the tongue on the battery cartridge with the ...
-
Makita 6202DW - page 8
If you charge a battery cartridge from a just-operated tool or a battery cartridge which has been left in a location exposed to direct sunlight or heat for a long time, the charg- ing light may flash in red color. If this occurs, wait for a while. Charging will begin after the battery cartridge cools. The battery cartridge will cool faster if you r ...
-
Makita 6202DW - page 9
Switch action I Tool speed is increased by increasing pres- sure on the trigger. To start the tool, simply pull the trigger. Release the trigger to stop. Switch trigger3.p ' CAUTION : Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position ...
-
Makita 6202DW - page 10
Adjusting fastening torque 4.5 (1 1/64',) 4.8 13/16") 5.1 113164'1 5.5 17/32',) The fastening torque can be adjusted in six stages by turning the adjusting ring so that the pointer on the adjusting ring points to a number on the tool body. The fastening torque is minimum when the pointer points to the number 1 and maximum when i ...
-
Makita 6202DW - page 11
Drilling operation First, turn the adjusting ring so that the pointer on the adjusting ring points to the *- marking. Then proceed as follows. 0 Drilling in wood When drilling in wood, best results are obtained with wood drills equipped with a guide screw. The guide screw makes drilling easier by pulling the bit into the workpiece. 0 Drilling in m ...
-
Makita 6202DW - page 12
MAINTENANCE CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 12 ...
-
Makita 6202DW - page 13
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Bits I Size I Part NO. Slotted .- 1 #ffF 1 7840 ...
-
Makita 6202DW - page 14
Sep.-08-’94 US CORDLESS DRIVER DRILL Model 6202D Note: The switch and other part configurations may differ from country to country. 14 ...
-
Makita 6202DW - page 15
MODEL 62020 Sep.-08-'94 US DESCRIPTION :SD DESCRIPTION MACHINE __ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 1 1 1 7 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 Housmg Set IWith Item 591 Name Plate Pan Head Screw M4x22 Wth Washer) Tapptng Screw BT4x20 Hand Strap Set Plate Switch Lever Swi ...
-
Makita 6202DW - page 16
Recycling the Battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. To recycle the battery: 1. Remove the battery from the tool. 2. a). or b) . I Ni-Cd I Take the battery to your nearest Makita Factory Service Center Take the battery to your nearest Makita Authorized Service Center or ...
Hai una domanda su Makita 6202DW?
Utilizza il modulo sottostante
Se non hai risolto il problema con Makita 6202DW con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Makita 6202DW è probabile che voglia condividere il modo di risolverlo.