-
Miele PG 8083 SCVi - page 1
Operating instructions Commercial dishwasher PG 8083 SCVi To avoid the risk of personal injury or damage to the appliance, it is essential that you read the operating and installation instructions before installation and use. M.-Nr. 09 501 370 e n-C A ...
-
Miele PG 8083 SCVi - page 2
Guide to the manual ...............................................5 Guide to the commercial dishwasher .................................6 Overview .........................................................6 Control panel ......................................................7 Intended use ......................................................8 Safe ...
-
Miele PG 8083 SCVi - page 3
Bottle holder ...................................................3 5 Cutlery ..........................................................3 6 3D cutlery tray ..................................................3 6 Operating the commercial dishwasher ...............................3 7 Detergent ........................................................3 7 ...
-
Miele PG 8083 SCVi - page 4
Program guide ...................................................6 4 Service .........................................................6 7 Repairs .......................................................6 7 Program updates ...............................................6 7 Electrical connection ..............................................6 8 Plumbi ...
-
Miele PG 8083 SCVi - page 5
Text which is highlighted or emphasized Warnings , Warnings marked with a thick framed box and a warning symbol contain safety information concerning potential injury and damage. ! Read the warnings carefully and follow the instructions and directions. Notes Notes contain information that is particularly important to follow and are highlighted in a ...
-
Miele PG 8083 SCVi - page 6
Overview a Upper spray arm (not visible) b Cutlery tray c Upper basket d Middle spray arm e Air inlet for drying f Lower spray arm g Filter combination h Data plate i In-operation indicator light j Rinse aid reservoir k Dual-compartment detergent dispenser l Reservoir for regenerating salt Guide to the commercial dishwasher 6 ...
-
Miele PG 8083 SCVi - page 7
Control panel a Display b 4 ü button, (additional programs) with indicator light c , button (Delay start) with indicator light d G button + (Extra drying) with indicator light e Program selection f X button (Program selector) for scrolling through the programs g - (On/Off) button with indicator light h In-operation indicator light Guide to the com ...
-
Miele PG 8083 SCVi - page 8
This commercial dishwasher complies with all current safety requirements. However, improper use can result in personal injury and material damage. To avoid the risk of accidents and damage to the appliance, read the operating instructions carefully before using the appliance for the first time. They contain important information on installation, sa ...
-
Miele PG 8083 SCVi - page 9
~ Use this commercial dishwasher only for "Dishwashing" as defined in the Operating instructions, i.e. for cleaning dishes and cutlery. Any other use, conversion or modification is not permissible and possibly hazardous. Miele will not be held liable for damage caused by inappropriate use or improper operation. ~ This commercial dishwashe ...
-
Miele PG 8083 SCVi - page 10
Proper installation ~ Do NOT install the appliance in an area where there is a risk of explosion or freezing. ~ To ensure the stability of undercounter commercial dishwashers, they must only be installed beneath a continuous countertop that is bolted to the adjacent cabinetry. ~ In order to reduce the risk of damage from condensation, the furniture ...
-
Miele PG 8083 SCVi - page 11
~ Do not connect the appliance to the electrical power supply until all the installation work has been completed, including adjustment of the door spring. ~ The electrical safety of this appliance is only ensured if it is properly grounded in compliance with applicable safety regulations. If in doubt, have the on-site wiring checked by a qualified ...
-
Miele PG 8083 SCVi - page 12
~ Do NOT use the appliance if the power cord is damaged. A damaged power cord must be replaced with a special cord. For safety reasons, the cord must be installed by Miele Service. ~ Before servicing the appliance, disconnect it from the power supply. ~ The plastic housing of the water connection contains an electrical valve. Do not immerse the hou ...
-
Miele PG 8083 SCVi - page 13
Proper use ~ This commercial dishwasher is designed only for operation with water and detergents designed for dishwashers or professional dishwashers. Organic solvents or flammable liquids must NOT be used in the appliance. There is a risk of explosion and/or damage through the destruction of rubber or plastic components resulting in leaks. ~ Only ...
-
Miele PG 8083 SCVi - page 14
~ Foam escaping from the wash cabinet can damage the appliance. If any foam is escaping, cancel the program immediate - ly! ~ When using detergents and special products, always follow the manufacturer's instructions. In order to avoid material damage or potential chemical reactions (such as explosive hydrogen gas reactions), use detergents onl ...
-
Miele PG 8083 SCVi - page 15
Children in the vicinity ~ Always supervise any children in the vicinity of the appliance. Never allow children to play with the appliance. Among other hazards, children run the risk of locking themselves in the commercial dishwasher! ~ Do not allow children to operate the commercial dishwasher. ~ Keep detergents away from children! If detergents a ...
-
Miele PG 8083 SCVi - page 16
Disposal of the packaging The packaging protects the commercial dishwasher from damage during shipping. They have been selected for environmental friendliness and can be recycled. The packaging comprises the following materials: Exterior packaging: – Corrugated cardboard made of up to 100% recycled material, or: polyethylene (PE) stretch wrap fil ...
-
Miele PG 8083 SCVi - page 17
Energy saving washing This commercial dishwasher is a water and energy saving appliance. For best results follow these tips: ^ You may connect the commercial dishwasher to a hot water line. This is particularly suitable with energy-saving water heating sources such as solar energy systems. If the hot water system is electrically heated and if loads ...
-
Miele PG 8083 SCVi - page 18
To open the door At the end of programs with a drying cycle (see "Program guide") the door will automatically open a little in order to improve the drying. You can cancel this function (see "Settings menu - AutoOpen"). ^ Pull the handle. If the door is opened during operation the commercial dishwasher will automatically stop run ...
-
Miele PG 8083 SCVi - page 19
Display functions General The following functions can be selected or set with the display: – the wash program – the Delay start time – the settings The following appears in the display while a program is running: – the present program step – the estimated remaining runtime – any faults or other messages In order to save energy, the dish ...
-
Miele PG 8083 SCVi - page 20
Basic settings ^ Press the - button to turn the commercial dishwasher on. If the commercial dishwasher is being turned on for the first time, the welcome screen will appear. Language The display automatically switches to the language setting. For details about the display, see chapter Display. ^ Select the desired language and confirm with the cent ...
-
Miele PG 8083 SCVi - page 21
Before using the commercial dishwasher for the first time you will need: – approx. 1 kg reactivation salt, – approx. 110 ml rinse aid, – for detergent see "Operating the commercial dishwasher". For available process chemicals from Miele contact Miele Professional. Every commercial dishwasher is tested before leaving the factory. The ...
-
Miele PG 8083 SCVi - page 22
^ Only open the door half way when adding salt to avoid spilling it. ^ Press the button on the top of the salt reservoir in the direction of the arrow. The cover will pop open. ^ Open the funnel. Do not fill water into the salt reservoir! ^ Only add just enough salt to fill the reservoir. Depending on the type of salt, the reservoir will hold up to ...
-
Miele PG 8083 SCVi - page 23
Refill salt indicator ^ Refill the salt reservoir as soon as the F Add salt message is displayed (if it appears during a program, wait until the end of the program). ^ Press the centre button to confirm. The Refill salt indicator goes out. If a sufficiently high concentration of salt has not yet formed, Refill salt may continue to be displayed afte ...
-
Miele PG 8083 SCVi - page 24
Rinse aid Rinse aid helps to prevent spotting on dishes and glassware and speeds up the drying process. The rinse aid is filled into the reservoir and the set amount will be automatically dispensed. For available process chemicals from Miele contact Miele Professional. , Use rinse aid only. Never fill the rinse aid reservoir with regular dishwashin ...
-
Miele PG 8083 SCVi - page 25
^ Pour rinse aid into the reservoir until it is visible in the opening. The rinse aid reservoir holds approximately 110 ml. ^ Close the cover until you hear it click shut, otherwise water might enter the reservoir during the wash program. ^ Wipe up any spilled rinse aid to prevent over-foaming during the next wash program. You can adjust the rinse ...
-
Miele PG 8083 SCVi - page 26
Tips: Remove coarse food residues from the dishware. There is no need to rinse items under running water! , Do not wash items soiled with ash, sand, wax, grease or paint in the commercial dishwasher. These materials damage the commercial dishwasher. All items can be placed anywhere in the baskets. However, note the following: – Do not place dishe ...
-
Miele PG 8083 SCVi - page 27
Items not recommended for dishwashing: – Wooden cutlery and dishes or items with wooden parts, as they may discolour and fade. In addition, the glue used in these items is not dishwasher-proof. This may result in wooden handles coming loose. – Hand-crafted items, antiques, valuable vases and decorative glassware are also not dishwasher-proof. ? ...
-
Miele PG 8083 SCVi - page 28
Typical load for 10 place settings with cutlery tray Upper basket Lower basket Cutlery tray Loading the commercial dishwasher 28 ...
-
Miele PG 8083 SCVi - page 29
Typical load for 16 place settings with cutlery tray Upper basket Lower basket Cutlery tray Loading the commercial dishwasher 29 ...
-
Miele PG 8083 SCVi - page 30
Upper basket , For safety reasons use the commercial dishwasher with both the upper and lower baskets inserted. ^ Load the upper basket with small, lightweight or delicate items such as cups, saucers, glasses, dessert bowls, etc. Shallow pans can also be placed in the upper basket. ^ Long items such as soup ladles, mixing spoons and long knives sho ...
-
Miele PG 8083 SCVi - page 31
XXL cup rack The cup rack can be set to two different widths so that it can also accommodate large cups. ^ Pull the cup rack upwards and click it back into position at the required width. Glass support bar The support bar will hold tall glasses and stemware securely. ^ Fold the support bar down and lean the glasses against it. ^ You can also move o ...
-
Miele PG 8083 SCVi - page 32
Adjusting the upper basket In order to gain more space for taller items in the lower or upper basket, the upper basket can be adjusted to three levels of about 2 cm height difference between each level. The upper basket can also be set at an angle with one side high and the other side low to improve water drainage. However, make sure that the baske ...
-
Miele PG 8083 SCVi - page 33
Lower basket ^ Place larger and heavier items such as plates, serving platters, saucepans, bowls, etc. in the lower basket. It can also be used for glasses, cups, small plates and saucers. Commercial dishwasher with a cutlery tray Heavily soiled items ^ Place very large plates in the centre of the lower basket. When tilted, plates up to 35 cm in di ...
-
Miele PG 8083 SCVi - page 34
Removable MultiComfort insert The rear section of the lower basket is used for washing cups, glasses, plates and pots. You can remove the MultiComfort insert to make more room for larger items such as pots and pans. To remove the insert ^ Press the yellow handle forwards and remove the insert. To replace the insert ^ Fit the insert into the lower b ...
-
Miele PG 8083 SCVi - page 35
Glass support bar The support bar will hold tall glasses and stemware securely. ^ Fold the support bar down and lean the glasses against it. Foldable spikes The spikes at the front are used for washing plates, soup bowls, platters, desert bowls, and saucers. Both rows of spikes can be folded down to create more room for larger dishware, e. g. pots, ...
-
Miele PG 8083 SCVi - page 36
Cutlery 3D cutlery tray ^ Arrange the cutlery in the tray as shown. To make unloading much easier, cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc. Spoon heads should be placed in contact with at least one of the serrated retainers on the base of the cutlery tray to ensure that water runs off them freely. The ...
-
Miele PG 8083 SCVi - page 37
Detergent Powder detergents Pour powder detergent into the compartments of the detergent dispenser. Never use detergent tablets. The tabs do not dissolve cempletely during the short program runtimes. ^ Put detergent into the dispenser compartments. Detergent dosage ^ Unless otherwise specified, depending on the degree of soiling, pour 20 to 30 g of ...
-
Miele PG 8083 SCVi - page 38
, Avoid inhaling powder detergents. Avoid swallowing dishwasher detergent. Detergents can cause chemical burns to nose, mouth and throat. Consult a doctor immediately if detergent has been swallowed or inhaled. Always keep detergent out of the reach of children. Keep children away from the commercial dishwasher when the door is open. There could st ...
-
Miele PG 8083 SCVi - page 39
Turning the commercial dishwasher on ^ Turn on the water supply if it is off. ^ Open the door. ^ Make sure the spray arms can rotate freely. ^ Press the - button to turn the commercial dishwasher on. The factory-set Normal program will appear in the display and the matching indicator light will come on. After a short while, the estimated time for t ...
-
Miele PG 8083 SCVi - page 40
Time display Before the program starts, the display shows the runtime of the selected program in hours and minutes. The remaining runtime is displayed during the program. Symbols will appear to indicate the stage of the program: 1 Pre-wash 8 Main wash % Interim rinse ( Final rinse G Drying O End (Finished) The runtime that is displayed may vary for ...
-
Miele PG 8083 SCVi - page 41
End of program At the end of a program, the In-operation indicator light will be visible flashing slowly with the door shut. The program has finished when O Finished or AutoOpen appears in the display and the door is slightly ajar (if applicable). If Extra drying was selected and AutoOpen is active, the drying fan will run for a few minutes after t ...
-
Miele PG 8083 SCVi - page 42
Interrupting a program A program will be interrupted as soon as the door is opened. When the door is closed again, the program will continue from where it was interrupted. , Water in the commercial dishwasher may be hot. Risk of scalding! Only open the door if absolutely necessary and be very careful. Before closing the door again, leave it slightl ...
-
Miele PG 8083 SCVi - page 43
Extra drying For better drying results and to reduce the amount of steam that escapes when the door is opened, the Extra drying function extends the fan runtime at the end of the program. This function is not available for all programs. When Extra drying is selected, the total program runtime will increase by approx. 20-30 minutes, depending on the ...
-
Miele PG 8083 SCVi - page 44
Delay start The start time of a program can be delayed, for instance to take advantage of cheaper electricity rates at night. You can delay the start time by 30 minutes to 24 hours. The delay is set in 30 minute increments. When using the Delay start function, make sure that the detergent compartment is dry before adding detergent. Wipe dry if nece ...
-
Miele PG 8083 SCVi - page 45
BrilliantLight This dishwasher has interior lighting. When the door is open the lighting will switch off automatically after 15 minutes. You can also switch off the interior lighting permanently. ^ Half open the dishwasher door and quickly swing it back and forth three times. When doing this, open the door wide enough for the interior lighting to s ...
-
Miele PG 8083 SCVi - page 46
Check the overall condition of your commercial dishwasher regularly (approx. ever y4-6 months). This will help to prevent problems. , The outer surfaces of the commercial dishwasher are susceptible to scratching. Contact with unsuitable cleaning agents can alter or discolour the outer surfaces. Cleaning the wash cabinet The wash cabinet is largely ...
-
Miele PG 8083 SCVi - page 47
Cleaning the control panel and front of the commercial dishwasher , Remove any soiling immediately. Otherwise it might become impossible to remove and could cause an alteration or discolouration of the surfaces. ^ The control panel should only be wiped with a damp cloth. ^ Clean the front of the appliance with a clean sponge, dishwashing liquid and ...
-
Miele PG 8083 SCVi - page 48
Checking the filters in the wash cabinet The filter combination in the base of the wash cabinet captures large dirt particles from the wash water. This prevents them from reaching the circulation system and re-entering the cabinet through the spray arms. , This commercial dishwasher must not be used without all the filters in place! Collection of c ...
-
Miele PG 8083 SCVi - page 49
The cover must be opened to clean the inside of the filter: ^ Push the clips together in the direction of the arrows as shown a , and open the cover b . ^ Clean all parts under running water. ^ Close the cover so that the lock engages. ^ Replace the filter combination so that it lies flat in the bottom of the wash cabinet. ^ Lock the filter in plac ...
-
Miele PG 8083 SCVi - page 50
Cleaning the spray arms Particles of food can get stuck in the spray arm jets and bearings. The spray arms should therefore be checked regularly (approx. ever y4-6 months). ^ Turn the dishwasher off. Remove the spray arms as follows: ^ Pull out the cutlery tray (if present). ^ Push the upper spray arm up to engage the inner ratchet and unscrew the ...
-
Miele PG 8083 SCVi - page 51
You can easily resolve many of the minor problems you may encounter during everyday use. This will save you time and money because you do not have to call Miele Service. , Repairs must only be carried out by Miele Service. Unauthorized repairs could cause personal injury or damage to the machine. Technical faults Problem Possible fault Solution The ...
-
Miele PG 8083 SCVi - page 52
Problem Possible fault Solution The In-operation indicator is flashing quickly. The buzzer is sounding. One of the following messages appears in the display: Before fixing the fault: – Turn the commercial dishwasher off with the - button. ; Fault FXX There may be a technical fault. After a few seconds: – Switch the commercial dishwasher back on ...
-
Miele PG 8083 SCVi - page 53
Faults in the water intake or water drain Problem Possible fault Solution The In-operation indicator is flashing quickly. The buzzer is sounding. One of the following messages appears in the display: 2 Open water supply The water tap is closed. Open the water tap all the way. 2 Water intake Before fixing the fault: – Turn the commercial dishwashe ...
-
Miele PG 8083 SCVi - page 54
Problem Possible fault Solution The In-operation indicator is flashing quickly. The buzzer is sounding. The following message appears in the display: 2 Drain Before fixing the fault: – Turn the commercial dishwasher off with the - button. Fault in the water drainage. There might be water in the wash cabinet. – Clean the filter combination (see ...
-
Miele PG 8083 SCVi - page 55
General problems with the commercial dishwasher Problem Possible fault Solution The indicators and display are dark. Only the - indicator flashes slowly. The indicators and the display turn off automatically to save energy (Standby mode). Press the - button to come out of Standby mode. The interior lighting does not come on when the door is opened. ...
-
Miele PG 8083 SCVi - page 56
Problem Possible fault Solution There are detergent residues in the dispenser at the end of a program. The dispenser was wet when detergent was added. Make sure the dispenser is dry before adding detergent. The detergent dispenser cover will not close. Detergent residue is blocking the latch. Remove the detergent residue. The inside of the door and ...
-
Miele PG 8083 SCVi - page 57
Noises Problem Possible fault Solution There is a knocking noise in the wash cabinet. A spray arm is hitting the dishware. Interrupt the program and rearrange items blocking the spray arms. There is a rattling noise in the wash cabinet. Dishware is moving around in the wash cabinet. Interrupt the program and rearrange loose pieces. A foreign object ...
-
Miele PG 8083 SCVi - page 58
Poor cleaning results Problem Possible fault Solution The dishes are not clean. The dishes were not loaded correctly. See Loading the commercial dishwasher. The program was not suitable for the requirements. Select a more suitable program (see Program guide). Not enough detergent was dispensed. Use more detergent, or switch to another detergent. Th ...
-
Miele PG 8083 SCVi - page 59
Problem Possible fault Solution Dishes are not dry, or glasses and cutlery are spotty. The rinse aid dosage is set too low or the rinse aid reservoir is empty. Refill the reservoir, increase the dosage, or switch the rinse aid product when refilling (see Rinse aid). Dishes were taken out too soon. Leave dishes in longer (see Operating the commercia ...
-
Miele PG 8083 SCVi - page 60
Problem Possible fault Solution Glasses have a brownish-blue discolouration; the deposit cannot be wiped off. Detergent deposits. Switch to another detergent right away. Glasses are dull and discoloured; the deposit cannot be wiped off. The glasses are not dishwasher-safe. Surface changes occur. There is no remedy. Use only dishwasher safe glasses. ...
-
Miele PG 8083 SCVi - page 61
Cleaning the water inlet screen There is a screen in the screw connection of the water inlet hose to protect the water inlet valve. The screen must be cleaned when dirty, otherwise insufficient water will flow into the wash cabinet. , The plastic housing of the water connection contains an electric valve. The housing must not be immersed in water. ...
-
Miele PG 8083 SCVi - page 62
Cleaning the drain pump and non-return valve If there is water in the wash cabinet at the end of a program, the water was not pumped out properly. The drain pump or the non-return valve might be clogged. However, they are easy to clean. ^ Disconnect the commercial dishwasher from the electric power supply. Always switch the appliance off before unp ...
-
Miele PG 8083 SCVi - page 63
Making better use of the commercial dishwasher Optional accessories for this commercial dishwasher are available from Miele. You want to... You need... ...wash the individual parts of the Miele Cappucinatore ... a Cappucinatore insert for the upper basket ...wash additional cutlery ... a cutlery basket for the lower basket ...wash long-stemmed glas ...
-
Miele PG 8083 SCVi - page 64
Program Application Detergent Follow the detergent manufacturer's instructions Compartment I 1) Compartment II 1) I ProSpeed For fresh, non-sticky food residues 2 0-3 0g J Universal For normal, slightly dried food residues 2 0-3 0g K Pots & Pans For burned-on, very adherent, very dry, starchy or albuminous 1) food residues. 1 0g 2 0-3 0g ! ...
-
Miele PG 8083 SCVi - page 65
Program sequence Pre- rinse Main wash Interim rinse I Interim rinse II 2) Final rinse Drying Extra drying Auto Open Water plus X 65°C 1 min X 10 s (X) X 65°C 3) 30 s (X) 4) (X) X 65°C 10 min X 3 min (X) X 65°C 3) 1.5 min (X) (X) (X) X 8 min X 75°C 10 min X 3 min (X) X 65°C 3) 1.5 min (X) (X) (X) X 50°C 1 min X 3 min (X) X 50°C 1 min (X) (X) ...
-
Miele PG 8083 SCVi - page 66
Program Consumption 6) Duration 6) Electrical energy Water Cold water connection (15°C) Water - Hot 55°C Cold water connection (15°C) Water - Hot 55°C I ProSpeed 1.7 kWh 0.9 kWh 17 l 35 min 7) 25 min 7) J Universal 1.7 kWh 1.0 kWh 17 l 48 min 7) 38 min 7) K Pots & Pans 2.0 kWh 1.0 kWh 23 l 64 min 7) 52 min 7) ! Glasses 1.1 kWh 0.4 kWh 17 l ...
-
Miele PG 8083 SCVi - page 67
Repairs If you cannot fix a fault with the help of this manual, please contact: – Miele Service. ^ When contacting the service department, you will need the model and serial number of your appliance. These can be found on the data plate along the right edge of the open door. Program updates The program update function keeps your appliance up to d ...
-
Miele PG 8083 SCVi - page 68
, All work on the electrical connection must be carried out by Miele Service. – The electrical installation must be in compliance with current local and national safety regulations. – The plug connection must comply with national regulations. (The electrical outlet must be accessible after the appliance has been installed.) This facilitates acc ...
-
Miele PG 8083 SCVi - page 69
The PG 8083 SCVi comes equipped with a 10/4 AWG cord and a 120V/208-240 V, 60 Hz NEMA 14-30P plug. If available, the dishwasher may be connected to a AC 120 V, 60Hz power supply. Converting the machine to a different type of power supply can lead to longer program runtimes resulting in increased energy consumption. 120V 208-240V Rated Load (kW) 1.5 ...
-
Miele PG 8083 SCVi - page 70
Removing the base cover The electrical terminal is located behind the front cover in the middle of the commercial dishwasher base. , Disconnect the commercial dishwasher from the electrical power supply! ^ Unscrew the 2 screws (left and right) and remove the base panel. ^ Screw the base panel back on when work on the connection is finished. Follow ...
-
Miele PG 8083 SCVi - page 71
The Miele waterproof system Providing the dishwasher was installed correctly by a qualified technician, the waterproof system will protect you from water damage throughout the lifetime of the machine. Water intake , The water in the commercial dishwasher is NOT safe to drink! – The commercial dishwasher must be connected to the water supply in ac ...
-
Miele PG 8083 SCVi - page 72
, To prevent damage to the commercial dishwasher, make sure all air has been bled from the supply line. ! The inlet hose must not be shortened or damaged in any way because it contains electrical wires (see illustration). Plumbing 72 ...
-
Miele PG 8083 SCVi - page 73
Water drainage – The drain is equipped with a non-return valve which prevents waste water from flowing back into the commercial dishwasher through the drain hose. – The commercial dishwasher drain hose should be connected to a separate drain for the commercial dishwasher only. If no separate drain is available, we recommend connecting it to a d ...
-
Miele PG 8083 SCVi - page 74
Model Commercial dishwasher PG 8083 SCVi Height 84.5 cm (adjustable +6.5 cm) Installation height Min. 84.5 cm (+ 6.5 cm) Width 59.8 cm Installation width 60 cm Depth 57 cm Weight 57.5 kg Voltage Connected load see data plate Fuse rating Power consumption when switched off 0.30 W Power consumption when not switched off 2.00 W Water pressure (flow pr ...
-
Miele PG 8083 SCVi - page 75
"Settings" menu for changing standard settings Opening the "Settings "menu ^ If the commercial dishwasher is on, press the - button to turn it off. ^ Press and hold the X button. ^ Turn the commercial dishwasher on with the - button and hold the X button down for at least 4 more seconds. The first option of the Settings menu wil ...
-
Miele PG 8083 SCVi - page 76
Water hardness Your commercial dishwasher comes with with a water softener. You must set the system to the water hardness level of your water supply. – The commercial dishwasher must be programmed to exactly match the hardness of your water. – Your local waterworks can tell you the water hardness level in your area. – Where the water hardness ...
-
Miele PG 8083 SCVi - page 77
Rinse aid For best results the rinse aid dosage can be adjusted. The dosage can be set between 0-6 ml. The factory setting is 3 ml of rinse aid. If the dishes are spotty: – Use a higher rinse aid setting. If the dishes are cloudy or streaky: – Use a lower rinse aid setting. ^ Select the desired amount of rinse aid and press the centre button to ...
-
Miele PG 8083 SCVi - page 78
AutoOpen To improve drying, the door automatically opens a little at the end of a program, except for Rinse & Hold, ProSpeed and Glass no rinse aid (see Program guide). With the Universal, Pots & Pans and Glasses programs, AutoOpen can only be activated by selecting Extra drying (see Additional functions - Extra drying). You can also deacti ...
-
Miele PG 8083 SCVi - page 79
The refill messages can be turned off without first refilling to let the commercial dishwasher go into Standby mode. But the fault messages cannot be turned off. Refill messages If you want the commercial dishwasher to switch to Standby mode in spite of the Refill messages, you can switch both indicator lights off together. ^ Select the desired set ...
-
Miele PG 8083 SCVi - page 80
Detergent dosage This function becomes visible when External dos. is activated. The detergent dosage can be set in millilitres or percent. Contact Miele Professional for the setting. – Amount in ml The factory setting is 30 ml. The dosage can be set from 10 - 100 ml in 2 ml increments. – Amount as % The factory setting is 0.50%. The dosage can ...
-
Miele PG 8083 SCVi - page 81
Venting the Dos. system The Dos. system will not dispense reliably if there is air in the system. The Dos. system must be vented – if it is being used for the first time, – if the liquid detergent reservoir was not refilled on time and the Dos. system was sucked empty. , To ensure that the Dos. system functions properly, prior to venting make s ...
-
Miele PG 8083 SCVi - page 82
Showroom program Demo mode for showrooms only! The commercial dishwasher is equipped with various demo programs for showroom use. – Demo with sound : This program activates the pumps to demonstrate the sound of the dishwasher washing (without water). – Demo AutoOpen : The door will open automatically. To switch Demo mode on ^ Select the desired ...
-
Miele PG 8083 SCVi - page 83
General requirements for measuring noise The dishwasher must be loaded with 16 place settings and the Normal program must be used. Installation requirements for measuring noise The dishwasher must be installed as follows:. ^ Install the dishwasher into an appropriate housing unit. ^ Secure the front panel. Noise measurement 83 ...
-
Miele PG 8083 SCVi - page 84
^ Push the insulation mat supplied (depending on model) under the plinth until it is up against the appliance feet a . ^ Attach the toe-kick so that it is flush with the door front b . Noise measurement 84 ...
-
Miele PG 8083 SCVi - page 85
85 ...
-
Miele PG 8083 SCVi - page 86
86 ...
-
Miele PG 8083 SCVi - page 87
87 ...
-
Miele PG 8083 SCVi - page 88
M.-Nr. 09 501 370 / 01 Subject to change without notice / Publication date 2013-06-12 ...
Hai una domanda su Miele PG 8083 SCVi?
Utilizza il modulo sottostante
Se non hai risolto il problema con Miele PG 8083 SCVi con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Miele PG 8083 SCVi è probabile che voglia condividere il modo di risolverlo.