Italiano dropdown-ico

Manuale per l’uso MTD 410 Series

24 pagine 3.34 mb
Scarica

Vai alla pagina of 24

Summary
  • MTD 410 Series - page 1

    Rear Tine Tiller Model Series 410 Oper ator’ s Man ual IMPOR T ANT : READ SAFETY R ULE S AND INSTR UCTIONS CAREFULL Y MTD LLC, P .O . BO X 361131 CLEVELAND , OHIO 44136-0019 Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest- covered, brush-covered or grass-covered land unless ...

  • MTD 410 Series - page 2

    2 This Operator’s Man ual is an important part of your new tiller. It will help you assemble, prepare and maintain the u nit for best performan ce. Please read and understand what it s ays. TABLE OF CONTENTS FINDING AND RECORDING MODEL NUMBER CUSTOMER SUPPORT Please do NOT return the unit to the re tailer from where it was purchased, without firs ...

  • MTD 410 Series - page 3

    3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: This symbol points out important safety in structions which, if not followed, could endanger the person al safety and/or propert y of yourself and others. Read an d follow all instructions in this manual before atte mpting to operate this machine. Fa ilure to comply with these instructions ma ...

  • MTD 410 Series - page 4

    4 7. Never operate the machine at high transport speeds on hard or slippery surfaces. 8. Exercise caution to avoid slipping or falling. 9. Look down and behind and use care when in reverse or pulling machine towards you. 10. Start the engine according to the instructions found in this manual and keep feet well away from the tines at all times. 11. ...

  • MTD 410 Series - page 5

    5 SECTION 2: ASSEMBLING YOUR TILLER NOTE: This operator’s man ual covers various mo dels of tillers. The units illustra ted may vary slightly from your unit. Follow only thos e instructions which pertain to your model number. NOTE: References to right or left side of the tiller are determined from be hind the unit in the operat ing position. T o ...

  • MTD 410 Series - page 6

    6 Figure 3 • Place the h ex opening of the f lange nut retain er bracket over the flange nut securi ng the handle adjustment crank and install the loc k nut on the lower shoulder bolt. See Figure 4. • Pivot handle a ssembly into position desired. Tighten the bott om bolt, lock nut, and the han dle adjustment lock securely. Figure 4 Attaching Ge ...

  • MTD 410 Series - page 7

    7 • Remove one hex nut fr om the threaded casing on the end of the cable. Slip t he wire up through the slot on the cable br acket underneath the ha ndle. • Push the end of the casing up throu gh the cable bracket. Rethrea d the hex nut on the end of t he cable. Do not tighten at t his time. Figure 7 • Pull the cable upwards to obtain slack a ...

  • MTD 410 Series - page 8

    8 SECTION 3: KNOW YOUR TILLER Figure 8 WARNING: Read, understand, and follow all instructions and warnings on the machine and in this manua l before operating. Gear Selection Handle The gear sele ction handle is locat ed on the front of the handle assembly. It is used to select NEUTRAL, REVERSE, or one of the FORWARD modes. This tiller is designed ...

  • MTD 410 Series - page 9

    9 Choke Lever (If Equipped) The choke lever is located on t op of the carburetor on the back of the en gine underneath the mu ffler. It is used to enrich the fuel mixture in the carburetor when starting a cold engine. Be careful when disengaging the Choke, especially after the engine warms up, the muffler will be hot! Primer Button (If Equipped) Th ...

  • MTD 410 Series - page 10

    10 SECTION 4: OPERATING YOUR TILLER WARNING: Read, understand, and follow all instructions and warnings on the machine and in this manua l before operating. Before Starting Gas And Oil Fill-Up Service the eng ine with gasoline and oil as instructed in the separate engine manual packed with your tiller. Read instructio ns carefully. WARNING: Use ext ...

  • MTD 410 Series - page 11

    11 • When using the tiller for the first time, use the second adjustment hole fr om the top (1" of tilling depth). See Figu re 9. Figure 9 • When breaking up sod and for shallow cultivation, use the setting which gives 1" of tilling depth (second ho le from the top). Place the side sh ields in their lowest po sition. • For further d ...

  • MTD 410 Series - page 12

    12 SECTION 5: MAKING ADJUSTMENTS WARNING: Neve r attempt to make any adjustments while the eng ine is running, except where spec ified in operator’ s manual. Handle Adjustment The handle may be adjusted to the height desired and on Model 420 series, the handle ma y also be adjusted to be in line with the tiller or swung to the left or right. Refe ...

  • MTD 410 Series - page 13

    13 SECTION 6: MAINTAINING YOUR TILLER WARNING: Disconnect the spark plug wire and ground it against the engine before performing any re pairs or maintenance. Engine Refer to the separat e engine manual for engine maintenance instructions. Maintain engine oil as instructed in the separa te engine ma nual packed with your u nit. Read an d follow inst ...

  • MTD 410 Series - page 14

    14 NOTE: Upon reassembly, make certain the be lt is routed over the idler pulley a nd inside of belt keepers by engine pulley. See Figur e 10. Figure 10 Off-Season Storage If the tiller will not be used fo r a period longer than 30 days, the following steps should be taken t o prepare the tiller for storage. • Clean the exterior of engi ne and th ...

  • MTD 410 Series - page 15

    15 SECTION 7: TROUBLE SHOOTING GUIDE NOTE: For repairs beyond the minor adjustments above, contact your local authorize d service dealer. T r ouble P ossib le Cause(s) Corrective Ac tion Engine fails to start Fuel tank empty, or stale fuel. Throttle control lever not in correct starting position (if so equipped). Blocked fuel line. Dirty aircleaner ...

  • MTD 410 Series - page 16

    16 SECTION 8: PARTS LIST FOR MODEL SERIES 410 1 2 3 4 4 5 6 7 21 8 9 10 4 11 12 13 14 15 16 17 18 4 21 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 1 39 40 41 42 19 ...

  • MTD 410 Series - page 17

    17 Model Series 410 Ref. No. P art No. P art Description 1. 710 -1017 He x Screw 1/4-20 x.6 25 2. 786-0168 Shift Cov er - T ecumseh 3. 686-0095 Crank Shift Assembly 4. 712-04063 He x Lock Nut 5/16-18 5. 715-0120 Spiral Pin 6. 786-0117 Shift Cover Mounting Brack et 7. 710-3008 Hex Cap Scre w 5/16-18 x.75 8. 712-3010 Hex Nut 5/16-18 9. 736-0242 Bell ...

  • MTD 410 Series - page 18

    18 Model Series 410 1 2 3 4 5 6 7 10 11 12 13 14 15 16 17 19 20 21 22 13 23 15 11 24 25 26 27 25 1 28 4 29 3 2 30 9 31 32 33 34 35 36 37 38 39 40 40 41 42 43 44 45 46 47 48 49 50 51 52 51 53 48 ...

  • MTD 410 Series - page 19

    19 Ref. No. P art No. Part Description 1. 721-0378 Shaft Seal 1.0 Dia 2. 712-0378 Hex Nut 7/16-20 3. 736-0407 Bell Wash er.45 ID x 1.0 OD 4. 721-0379 Shaft Seal.7 5 Dia 5. 716-0865 Snap Ring.50 Dia 6. 686-0038 Gear Case Assembly - RH Half 7. 618-0245B Shift Assembly 9. 713-0233 Chain - #41 1/2” Pitch x 30 Links 10. 750-0570 Space 1.0 ID x 2.0 OD ...

  • MTD 410 Series - page 20

    20 1 1 2 3 4 5 6 7 8 9 10 11 9 13 14 15 16 18 17 19 20 21 22 23 24 25 26 27 28 10 29 30 30 31 33 33 34 35 35 36 17 37 46 39 17 38 32 17 40 41 43 42 12 17 44 45 47 Model Series 410 ...

  • MTD 410 Series - page 21

    21 Model Series 410 NOTE: For painted pa rts , please refer to th e list of color codes below. Please add the app licable color code, wherever needed, to the part number to order a rep lacemen t part. Fo r instance, if a part numbered 70 0-xxxx is painted Oyste r Gray, the part number to ord er would be 700-xxxx-066 2. Black — 0691; Black, Powder ...

  • MTD 410 Series - page 22

    22 NOTES ...

  • MTD 410 Series - page 23

    23 NOTES ...

  • MTD 410 Series - page 24

    MANUF A CTURER’S LIMITED W ARRANTY FOR: The limited warranty set forth below is given by MTD LLC with respect to new merchandise purchased and used in the United States, its poss e ssions and territories. “MTD”warrants this product against defects in material and workmanship for a period of two (2) years commenc ing on the date of original pu ...

Fabbricante MTD Categoria Tiller

I documenti che otteniamo dal fabbricante del dispositivoMTD 410 Series possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici MTD
- manuali per l’uso 410 Series
- schede prodotto MTD
- opuscoli
- o etichette energetiche MTD 410 Series
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso MTD 410 Series.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione MTD 410 Series, manuali di manutenzione, brevi manuali o manuali utente MTD 410 Series. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto MTD 410 Series.

Manuali per l’uso simili

Manuale completo del dispositivo MTD 410 Series, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare MTD 410 Series dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti MTD 410 Series.

Il manuale per l’uso completo MTD, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale MTD 410 Series - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice MTD 410 Series, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per MTD 410 Series che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo MTD 410 Series - che ci dovrebbe aiutare nei primi passi durante l'uso MTD 410 Series
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del MTD 410 Series
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio MTD 410 Series in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su MTD 410 Series?

Utilizza il modulo sottostante

Se non hai risolto il problema con MTD 410 Series con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con MTD 410 Series è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)