Italiano dropdown-ico

Manuale per l’uso Audiovox PRO9776C

24 pagine 0.49 mb
Scarica

Vai alla pagina of 24

Summary
  • Audiovox PRO9776C - page 1

    128-8787 1 of 24 1 SELECT ABLE FEA TURES The selectable features can be set manually as explained below , or with the RF feature programmer . T o set features using the RF programmer , follow the instructions packaged with the programmer . Factory default settings are indicated by bold text. Note : The method of manual override can either be select ...

  • Audiovox PRO9776C - page 2

    128-8787 2 of 24 2 T o program these selectable features; Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off Then On Short chirp, then long chirp This Action Accesses Feature Bank 2 Alarm Selectable Features First Press and release the valet switch ...

  • Audiovox PRO9776C - page 3

    128-8787 3 of 24 3 T o exit program mode, turn ignition off, or press and release valet switch. RF Programmable Features Bank 3 Is Remote Start Selectable Features: Feature Selection 1 Chirp 2 Chirps 3 Chirps 4 Chirps 5 Chirps 6 Chirps 1st Defrost Output Pulsed 10 Mins 2nd RF S tart Chirp O f f On On & Car Finder 3rd Run Time 5 Mins 10 Mins 15 ...

  • Audiovox PRO9776C - page 4

    128-8787 4 of 24 4 Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off, On, Off, On Short chirp, then 2 long chirps This Action Accesses Feature Bank 3 Remote S tart Selectable Features First Press the valet switch one time 1 chirp = defrost output ...

  • Audiovox PRO9776C - page 5

    128-8787 5 of 24 5 This Remote S tart/Alarm System is designed to be used with Automatic T ransmission V ehicles Only! The unit provides a selectable ignition control that allows a number of select able timed outputs for glow plug pre-heat which may be required for certain diesel vehicles, (see selectable feature #9). If the diesel engine has a ins ...

  • Audiovox PRO9776C - page 6

    128-8787 6 of 24 6 SHOCK SENSOR: Select a centrally located, solid mounting surface for the shock sensor that will allow consistent operation from all areas of the vehicle. The selected location must be within 18" of the control module to allow routing and connecting of the 4 pin harness. Secure the shock sensor to the chosen location using tw ...

  • Audiovox PRO9776C - page 7

    128-8787 7 of 24 7 Failure to make this connection properly can result in personal injury and property damage. In all installations it is the responsibility of the installing technician to test the remote start unit and assure that the vehicle cannot start via RF control in any gear selection other than park or neutral. In both mechanical and elect ...

  • Audiovox PRO9776C - page 8

    128-8787 8 of 24 8 WIRING THE 4 PIN AL TERNA TE IGNITION HARNESS ORANGE/BLACK Wire: Parking Brake Input This wire is used only when the turbo timer mode, Bank 3, feature # 16 is selected ON. This input insures that the vehicle parking brake is applied whenever the vehicle is set up for and the turbo timer circuit is used. This input must switch to ...

  • Audiovox PRO9776C - page 9

    128-8787 9 of 24 9 WIRING CONNECTIONS: Multi Pin Accessory Input/Output Harness White w/ Red T race Wire: Parking Light Flasher Feed This wire is the common contact of the on board parking light flasher relay . If the vehicle you are working on has +12 volt switched parking lights, connect this wire to a fused +12 volt source. (Max. 15 Amps) Note: ...

  • Audiovox PRO9776C - page 10

    128-8787 10 of 24 10 Purple Wire: (+) Door Trigger Input If the vehicle's door courtesy light switches +12 volts when the door is opened (some Fords and some Imports), you must connect this wire to the positive output from one of the vehicle's door pin switches. In most cases, the Purple wire will need to be connected to only one door swi ...

  • Audiovox PRO9776C - page 11

    128-8787 11 of 24 11 General Motors V A TS By-Pass Diagram Light Blue Wire: Ignition 3 Output This wire provides a 300 mA ground output that becomes active 3 seconds before the Remote S tart Unit initializes, and remains grounded while running plus an additional 4 seconds after the Remote S t art Unit turns off. In all of the applications described ...

  • Audiovox PRO9776C - page 12

    128-8787 12 of 24 12 Green w/ White trace Wire: Entry Illumination Ground Output This wire provides a 30 second ground output (300 mA Max.) whenever the remote is used to disarm the alarm or to unlock the doors and provides a continuous pulsed output whenever the alarm is triggered. This wire should be connected to an external relay , and wired to ...

  • Audiovox PRO9776C - page 13

    128-8787 13 of 24 13 Orange Wire: Ground When Armed Output This wire provides a 300 mA ground output when the alarm circuit is armed to control the starter inhibit relay . Connect the Orange wire to terminal #86 (orange wire) of the relay provided. Connect terminal #85 (red wire) of the relay to an ignition wire in the vehicle that is +12 volts whe ...

  • Audiovox PRO9776C - page 14

    128-8787 14 of 24 14 Black Wire: Chassis Ground Source Connect the Black wire to a known vehicle ground source or to a solid clean metal part of the chassis. Be certain to remove any paint or grease and secure this wire with a self taping screw and ring terminal. Chassis Ground Connection Detail Green w/ Orange T race Wire: T achometer Input Signal ...

  • Audiovox PRO9776C - page 15

    128-8787 15 of 24 15 Negative Door Switch Wiring Detail Dark Blue Wire: Delayed 300 mA Pulsed Channel 3 Output The Dark Blue wire supplies a 300 mA ground pulsed output whenever channel three of the receiver is accessed. Pressing the pre-programmed transmitter button for three seconds will access channel two. This is a low current output and must b ...

  • Audiovox PRO9776C - page 16

    128-8787 16 of 24 16 WIRING THE 4 PIN AUXILIARY OUTPUT HARNESS The auxiliary 4 pin connector provides low current outputs to control various functions in the vehicle during different stages of the Remote S tart unit's operation. Underst anding these outputs and the time in which they occur will allow you to determine if they are needed for the ...

  • Audiovox PRO9776C - page 17

    128-8787 17 of 24 17 2 Pin T ransponder Control Output: (Y ellow Connector) This output is intended to allow the control of a transponder bypass interface module or transponder bypass relay . The system also allows software selections to control the way in which this output operates, see remote start feature # 10 for setting this output. When the u ...

  • Audiovox PRO9776C - page 18

    128-8787 18 of 24 18 3 Wire Positive Switched Door Lock/Unlock Wiring Detail 3 Wire Ground Switched 2 Step Door Locks In this application, the red wire provides a ground pulse during arming, or the pulsed ground lock output. Connect the red wire to the wire that provides a low current ground signal from the factory door lock switch to the factory d ...

  • Audiovox PRO9776C - page 19

    128-8787 19 of 24 19 3 Wire Positive Switched 2 Step Door Locks The green wire provides a positive pulse during arming, or the pulsed +12 volt lock output. Connect the green wire to the wire that provides a low current positive signal from the factory door lock switch to the factory door lock control relay . The red wire provides a positive pulse d ...

  • Audiovox PRO9776C - page 20

    128-8787 20 of 24 20 3a. Within 10 seconds of turning the ignition switch off, Release and then Push On and release the Pushbutton Switch 2 times holding it on the second time until the siren and or lights flash and chirp 2 times indicating that the 2 Hour Start Interval has successfully been set. or 3b. Within 10 seconds of turning the ignition sw ...

  • Audiovox PRO9776C - page 21

    128-8787 21 of 24 21 TESTING YOUR INST ALLA TION: CAUTION!! The following procedure must be performed after the inst allation of an Audiovox Remote S tart Device. It is the responsibility of the installing technician to complete these tests. Failure to test the unit in the following manner may result in personal injury , property damage, or both. H ...

  • Audiovox PRO9776C - page 22

    128-8787 22 of 24 22 vehicle. The information concerning the Mechanical Neutral Safety Switch provided below will help you to determine if the vehicle you are working on has this type of safety switch and will provide alternate wiring methods to accommodate this situation. MECHANICAL NEUTRAL SAFETY SWITCH CONSIDERA TIONS: Mechanical neutral safety ...

  • Audiovox PRO9776C - page 23

    128-8787 23 of 24 23 METHOD 2 T o connect to the key in sensor circuit as shown for method 2: A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch. B. Cut this wire and connect the ignition cylinder side to chassis ground. C. Locate the key in sensor switch wire that connects the chime module to the ignit ...

  • Audiovox PRO9776C - page 24

    128-8787 24 of 24 24 © 2010 Audiovox Electronics Corp., Hauppauge, N.Y. 11788 128-8787 ...

Fabbricante Audiovox Categoria Automobile Alarm

I documenti che otteniamo dal fabbricante del dispositivoAudiovox PRO9776C possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Audiovox
- manuali per l’uso PRO9776C
- schede prodotto Audiovox
- opuscoli
- o etichette energetiche Audiovox PRO9776C
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Audiovox PRO9776C.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Audiovox PRO9776C, manuali di manutenzione, brevi manuali o manuali utente Audiovox PRO9776C. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Audiovox PRO9776C.

Manuali per l’uso simili

Manuale completo del dispositivo Audiovox PRO9776C, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Audiovox PRO9776C dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Audiovox PRO9776C.

Il manuale per l’uso completo Audiovox, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Audiovox PRO9776C - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Audiovox PRO9776C, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Audiovox PRO9776C che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Audiovox PRO9776C - che ci dovrebbe aiutare nei primi passi durante l'uso Audiovox PRO9776C
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Audiovox PRO9776C
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Audiovox PRO9776C in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Audiovox PRO9776C?

Utilizza il modulo sottostante

Se non hai risolto il problema con Audiovox PRO9776C con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Audiovox PRO9776C è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (1)

antonio garcia garcia

no puedo poner mi grabadora VN-711PC en modo (activación por voz) porque cuando la pongo en modo VCVA el manual dice que para activarlo pise ON y desactivar OF y esta grabadora carece de estos dos botones, cuando pulso el play o el MAS o el MENOS estando en VCVA me sale el mensaje CANCELAR AJUSTES DE GRABACION (que no estaba activarlo porque en las diferente pruebas que ago. no consigo que la voz la active.si me pueden orientar se lo agradecería. Gracias, saludos