-
Chicago Electric 98265 - page 1
1.5 HP 7” BRIDGE TILE SA W Model 98265 SET UP AND OPERA TING INSTRUCTIONS Note: Stand (SKU 98328) and Diamond Blade sold separately . Visit our website at: http://www .harborfreight.com Read this material before using this product. Failure to do so can result in serious injury . SA VE THIS MANUAL. Copyright © 2008 by Harbor Freight T ools ® . A ...
-
Chicago Electric 98265 - page 2
Page 2 For technical questions, please call 1-800-444-3353. SKU 98265 SA VE THIS MANUAL Keep this manual for the safety warnings and precautions, assembly , operating, inspec- tion, maintenance and cleaning procedures. Write the product’ s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product ...
-
Chicago Electric 98265 - page 3
Page 3 For technical questions, please call 1-800-444-3353. SKU 98265 RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS (120 VOL T) NAMEPLA TE AMPERES (at full load) EXTENSION CORD LENGTH 25’ 50’ 100’ 150’ 0 – 6 18 16 16 14 6.1 – 10 18 16 14 12 10.1 – 12 16 16 14 12 12.1 – 16 14 12 Do not use. T ABLE A 9. USE PROPER EXTENSION CORD. ...
-
Chicago Electric 98265 - page 4
Page 4 For technical questions, please call 1-800-444-3353. SKU 98265 GROUNDING INSTRUCTIONS TO PREVENT ELECTRIC SHOCK AND DEA TH FROM INCORRECT GROUNDING WIRE CONNECTION READ AND FOLLOW THESE INSTRUCTIONS: 1 10-120 V~ Grounded T ools: T ools with Three Prong Plugs 1. In the event of a malfunction or break- down, grounding provides a path of least ...
-
Chicago Electric 98265 - page 5
Page 5 For technical questions, please call 1-800-444-3353. SKU 98265 6. Do not perform any operation freehand. 7. Never reach around or over saw blade. 8. Make sure the workpiece is supported at all times while sawing. Use a roller stand (not provided) with larger work- pieces if necessary . 9. T o properly understand all safety warn- ings, be fam ...
-
Chicago Electric 98265 - page 6
Page 6 For technical questions, please call 1-800-444-3353. SKU 98265 check that the saw teeth are not en- gaged into the workpiece before turn- ing on the saw . • Push the wood stock past the blade prior to release. 1 1. Check guards for proper operation with saw disconnected from power before each use. Do not disable any guard. Do not operate s ...
-
Chicago Electric 98265 - page 7
Page 7 For technical questions, please call 1-800-444-3353. SKU 98265 Essential Straight Push-stick Features and Functions Note: Straight style (traditional) stick shown. A dif- ferent stick design may be used if it properly protects against all hazards. Diagram not to scale. • Push sticks must be made from sturdy , defect-free, plywood or normal ...
-
Chicago Electric 98265 - page 8
Page 8 For technical questions, please call 1-800-444-3353. SKU 98265 POSITION OF TILE SA W 1. T o avoid the possibility of the tool plug or receptacle getting wet, position tile saw to one side of a wall mounted receptacle to prevent water from dripping onto the receptacle or plug. The user should ar- range a “drip loop” in the cord connecting ...
-
Chicago Electric 98265 - page 9
Page 9 For technical questions, please call 1-800-444-3353. SKU 98265 12. Industrial applications must follow OSHA guidelines. 13. Maintain labels and nameplates on the tool. These carry important safety infor- mation. If unreadable or missing, con- tact Harbor Freight T ools for a replace- ment. 14. Avoid unintentional starting. Prepare to begin w ...
-
Chicago Electric 98265 - page 10
Page 10 For technical questions, please call 1-800-444-3353. SKU 98265 ngers), seek medical advice as soon as possible. 2. Do not smoke during use. Nicotine re- duces the blood supply to the hands and ngers, increasing the risk of vibration- related injury . 3. Wear suitable gloves to reduce the vibra- tion effects on the user . 4. Use tools ...
-
Chicago Electric 98265 - page 11
Page 1 1 For technical questions, please call 1-800-444-3353. SKU 98265 SPECIFICA TIONS Maximum Blade Diameter 7" Arbor Hole 5/8" Maximum Cutting Capacity 1-1/8" @ 90° 3/4" @ 45° T ilting Head 45° Left-T ilt only Electrical Requirements 120 V~ / 60 Hz / 10 A Blade Rated Speed 5000 RPM W ater Pump Maximum Flow = 160 GPH Stand ...
-
Chicago Electric 98265 - page 12
Page 12 For technical questions, please call 1-800-444-3353. SKU 98265 4. Fig. 1 The Handle (B13) must be installed onto the Holder (B09) using the two supplied Hex Screws (B12). (See Fig. 1.) 5. Fig. 2 Holding Clips Be sure the water pump (A25) is properly installed within its holding clips (see Fig. 2). Run the water hose from the pump discharge ...
-
Chicago Electric 98265 - page 13
Page 13 For technical questions, please call 1-800-444-3353. SKU 98265 General Operating Instructions 1. Fig. 3 Power Switch Reset Button When making a at cut, slide the piece to be cut up against the two Fence (D09,D12) halves securely and stabilize one side with the provided Clamp Plate. 2. When making an angled cut, position one end securely ...
-
Chicago Electric 98265 - page 14
Page 14 For technical questions, please call 1-800-444-3353. SKU 98265 MAINTENANCE AND SER VICING Procedures not specically explained in this manual must be performed only by a qualied technician. TO PREVENT SERIOUS INJUR Y FROM ACCIDENT AL OPERA TION: T urn the Power Switch of the tool to its “OFF” position and unplug the tool from its e ...
-
Chicago Electric 98265 - page 15
Page 15 For technical questions, please call 1-800-444-3353. SKU 98265 5. Remove the blade and replace with a new one. Make sure the arrow on the blade matches the direction of the arrow embossed on the blade cover . 6. With the at wrench in place again, reinstall the blade’s hex bolt turning clockwise, and tighten securely . 7. Replace the cl ...
-
Chicago Electric 98265 - page 16
Page 16 For technical questions, please call 1-800-444-3353. SKU 98265 Part Description Qty A01 Screw (M5x12) 5 A02 Hose Connect 1 A03 W ater Tubing 1 A04 Screw (M5x10) 2 A05 Inner Flange 1 A06 Bearing (6202RT) 1 A07 W asher (14) 1 A08 Bearing (628-R) 1 A09 Grounding Wire 1 A10 Front Motor Cover 1 A 11 Outer T eeth W asher 2 A12 Screw (M4x8) 2 A13 ...
-
Chicago Electric 98265 - page 17
Page 17 For technical questions, please call 1-800-444-3353. SKU 98265 P ARTS LIST AND ASSEMBL Y DIAGRAM B (HANGER) Part Description Qty . B01 Screw (M4x6) 3 B02 Screw (M4x20) 1 B03 Hex Nut (M4) 1 B04 Linear Bushing 2 B05 Felt Bushing 4 B06 Seal 4 B07 Bearing 4 B08 Hex Bolt (M6x20) 4 B09 Holder 1 B10 Knob 1 B 11 Flat W asher 2 B12 Screw (M5x12) 2 B ...
-
Chicago Electric 98265 - page 18
Page 18 For technical questions, please call 1-800-444-3353. SKU 98265 P ARTS LIST AND ASSEMBL Y DIAGRAM C (SUPPORT) Part Description Qty . C01 Steel Support B 1 C02 Connection Shaft 2 C03 Set Screw (M4x15) 7 C04 Flat W asher 2 C05 Knob 2 C06 Socket Wrench 1 C07 Spring W asher 7 C08 Flat W asher 9 C09 Wrench Holder 1 C10 Sliding Bar Support 1 C 11 ...
-
Chicago Electric 98265 - page 19
Page 19 For technical questions, please call 1-800-444-3353. SKU 98265 P ARTS LIST AND ASSEMBL Y DIAGRAM D (WORK T ABLE) Part Description Qty . D01 Hex Nut (M6) 20 D02 Spring W asher 24 D03 Flat W asher 24 D04 Stainless Steel Frame 1 D05 Hex Bolt (M6x30) 8 D06 T able End 2 D07 Right Fence Cover 1 1 D08 Scale 1 D09 Right Fence 1 D10 Right Fence Cove ...
-
Chicago Electric 98265 - page 20
Page 20 For technical questions, please call 1-800-444-3353. SKU 98265 P ARTS LIST AND ASSEMBL Y DIAGRAM E (W A TER TRA Y) Part Description Qty . EO1 W ater Tray 1 EO2 O-Ring 1 EO3 Drain Plug 1 EO4 Rubber Cap 1 EO5 Flat W asher 7 EO6 Set Screw 11 EO7 Rubber Feet 7 EO8 Carrying Handle Grip 2 REV 10b ...
-
Chicago Electric 98265 - page 21
Page 21 For technical questions, please call 1-800-444-3353. SKU 98265 LIMITED 90 DA Y W ARRANTY Harbor Freight T ools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days fro ...
Hai una domanda su Chicago Electric 98265?
Utilizza il modulo sottostante
Se non hai risolto il problema con Chicago Electric 98265 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Chicago Electric 98265 è probabile che voglia condividere il modo di risolverlo.