Italiano dropdown-ico

Manuale per l’uso Miller Electric 456 CC

40 pagine 0.77 mb
Scarica

Vai alla pagina of 40

Summary
  • Miller Electric 456 CC - page 1

    OM-188 422F June 2001 Processes Description Arc Welding Power Source Multiprocess W elding R Phoenix 456 CC/CV (400 V olt Models) Visit our website at www.MillerWelds.com ...

  • Miller Electric 456 CC - page 2

    Miller Electric manufactures a full line of welders and welding related equipment. For information on other quality Miller products, contact your local Miller distributor to receive the latest full line catalog or individual catalog sheets. T o locate your nearest distributor or service agency call 1-800-4-A-Miller , or visit us at www .MillerW eld ...

  • Miller Electric 456 CC - page 3

    The following terms are used interchangeably throughout this manual: TIG = GT AW Stick = SMAW T ABLE OF CONTENTS SECTION 1 – SAFETY PRECAUTIONS - READ BEFORE USING 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbol Usage 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Miller Electric 456 CC - page 4

    dec_con1 10/95 Declaration of Conformity For European Community (CE) Products Manufacturer ’s Name: Miller Electric Mfg. Co. Manufacturer ’s Address: 1635 W . Spencer Street Appleton, WI 54914 USA Declares that the product: Phoenix  456 CC/CV conforms to the following Directives and Standards: Directives Electromagnetic compatibility Directi ...

  • Miller Electric 456 CC - page 5

    OM-188 422 Page 1 SECTION 1 – SAFETY PRECAUTIONS - READ BEFORE USING som _nd_4/98 1-1. Symbol Usage Means W arning! W atch Out! There are possible hazards with this procedure! The possible hazards are shown in the adjoining symbols. Y Marks a special safety message. . Means “ Note ” ; not safety related. This group of symbols means W arning! ...

  • Miller Electric 456 CC - page 6

    OM-188 422 Page 2 Arc rays from the welding process produce intense visible and invisible (ultraviolet and infrared) rays that can burn eyes and skin. Sparks fly of f from the weld. ARC RA YS can burn eyes and skin. D Wear a welding helmet fitted with a proper shade of filter to protect your face and eyes when welding or watching (see ANSI Z49.1 an ...

  • Miller Electric 456 CC - page 7

    OM-188 422 Page 3 1-3. Additional Symbols For Installation, Operation, And Maintenance FIRE OR EXPLOSION hazard. D Do not install or place unit on, over , or near combustible surfaces. D Do not install unit near flammables. D Do not overload building wiring – be sure power supply system is properly sized, rated, and protected to handle this unit. ...

  • Miller Electric 456 CC - page 8

    OM-188 422 Page 4 1-5. EMF Information Considerations About W elding And The Ef fects Of Low Frequency Electric A n d M a g netic Fields W elding current, as it flows through welding cables, will cause electro- magnetic fields. There has been and still is some concern about such fields. However , after examining more than 500 studies spanning 17 ye ...

  • Miller Electric 456 CC - page 9

    OM-188 422 Page 5 SECTION 1 – CONSIGNES DE SECURITE – LIRE A V ANT UTILISA TION som _nd_fre 4/98 1-1. Signification des symboles Signifie Mise en garde ! Soyez vigilant ! Cette proc é dure pr é sente des risques de danger ! Ceux-ci sont identifi é s par des symboles adjacents aux directives. Y Identifie un message de s é curit é particulie ...

  • Miller Electric 456 CC - page 10

    OM-188 422 Page 6 Le rayonnement de l ’ arc du proc é d é de soudage g é n è re des rayons visibles et invisibles intenses (ultraviolets et infrarouges) susceptibles de provoquer des br û lures dans les yeux et sur la peau. Des é tincelles sont projet é es pendant le soudage. LES RA YONS DE L ’ ARC peuvent pro- voquer des br û lures dan ...

  • Miller Electric 456 CC - page 11

    OM-188 422 Page 7 1-3. Dangers suppl é mentaires en relation avec l ’ installation, le fonctionnement et la maintenance Risque D ’ INCENDIE OU D ’ EXPLOSION. D Ne pas placer l ’ appareil sur , au-dessus ou à proxi- mit é de surfaces infllammables. D Ne pas installer l ’ appareil à proximit é de produits inflammables D Ne pas surcharg ...

  • Miller Electric 456 CC - page 12

    OM-188 422 Page 8 1-4. Principales normes de s é curit é Safety in W elding and Cutting, norme ANSI Z49.1, de l ’ American Wel- ding Society , 550 N.W . Lejeune Rd, Miami FL 33126 Safety and Health Sandards, OSHA 29 CFR 1910, du Superintendent of Documents, U.S. Government Printing Of fice, W ashington, D.C. 20402. Recommended Safe Practice for ...

  • Miller Electric 456 CC - page 13

    OM-188 422 Page 9 SECTION 2 – DEFINITIONS 2-1. Manufacturer ’ s W arning Label Definitions W arning! W atch Out! There are possible hazards as shown by the symbols. 1 Electric shock from welding electrode or wiring can kill. 1.1 W ear dry insulating gloves. Do not touch electrode with bare hand. Do not wear wet or damaged gloves. 1.2 Protect yo ...

  • Miller Electric 456 CC - page 14

    OM-188 422 Page 10 > 60 s V S-179 190-A V V 1 W arning! W atch Out! There are possible hazards as shown by the symbols. 2 Electric shock from wiring can kill. 3 Disconnect input plug or power before working on machine. 4 Hazardous voltage remains on input capacitors after power is turned off. Do not touch fully charged capacitors. 5 Always wait ...

  • Miller Electric 456 CC - page 15

    OM-188 422 Page 1 1 2-2. Symbols And Definitions A Amperage Panel Alternating Current (AC) V V oltage Output Circuit Breaker Remote On Of f Gas Tungsten Arc W elding Negative V oltage Input Direct Current (DC) Positive Inductance Protective Earth (Ground) Constant Current Constant V oltage Foot Control Line Connection Arc Force Shielded Metal Arc W ...

  • Miller Electric 456 CC - page 16

    OM-188 422 Page 12 2-3. Manufacturer ’ s Rating Label S-184 765 / S-184 763 ...

  • Miller Electric 456 CC - page 17

    OM-188 422 Page 13 SECTION 3 – INST ALLA TION 3-1. Specifications Input Power Rated W elding Output Amperage Range V oltage Range Maximum Open- Circuit Amperes Input At Rated Load Output 60 Hz, Three-Phase V oltage DC 400 V KV A KW Three Phase 450 A @ 38 V o lts DC, 100% Duty Cycle; 565 A @ 38 V o lts DC, 60% Duty Cycle 5 – 600 10 – 38 95 31 ...

  • Miller Electric 456 CC - page 18

    OM-188 422 Page 14 3-3. V olt-Ampere Curves V olt-ampere curves show mini- mum and maximum voltage and amperage output capabilities of unit. Curves of other settings fall be- tween curves shown. va_curve1 4/95 – SA-181 561 / SA-181 562 CC Modes CV Modes 3-4. Dimensions And W eight Hole Layout Dimensions F A 14-21/64 in (363.9 mm) A B 20-3/4 in (5 ...

  • Miller Electric 456 CC - page 19

    OM-188 422 Page 15 3-5. Selecting A Location loc_2 3/96 - ST -800 61 1 / ST-802 260 1 Lifting Forks Use lifting forks to move unit. Extend forks beyond opposite side of unit. 2 Lifting Handles Use handles to lift unit. 3 Hand Cart Use cart or similar device to move unit. 4 Rating Label Use rating label to determine input power needs. 5 Line Disconn ...

  • Miller Electric 456 CC - page 20

    OM-188 422 Page 16 3-6. W eld Output T erminals And Selecting Cable Sizes Y ARC WELDING can cause Electromagnetic Interference. T o reduce possible interference, keep weld cables as short as possible, close together , and down low , such as on the floor . Locate welding operation 100 meters from any sensitive electronic equipment. Be sure this weld ...

  • Miller Electric 456 CC - page 21

    OM-188 422 Page 17 3-7. Remote 14 Receptacle Information Socket* Socket Information 24 VOL TS AC A 24 volts ac. Protected by circuit breaker CB2. 24 VOL TS AC B Contact closure to A completes 24 volts ac con- tactor control circuit. AJ B K I 1 15 VOL TS AC I 1 15 volts ac. Protected by circuit breaker CB1. B C L NH D M G 1 15 VOL TS AC J Contact cl ...

  • Miller Electric 456 CC - page 22

    OM-188 422 Page 18 3-8. 1 15 V olts AC Duplex Receptacle Ref. ST-801 524-A 1 1 15 V 7 A AC Receptacle Power is shared between duplex receptacle and Remote 14 recep- tacle (see Section 3-7). 2 Circuit Breaker CB1 3 Circuit Breaker CB2 CB 1 protects 1 15 volts ac portion of duplex receptacle and Remote 14 receptacle from overload. CB2 protects 24 vol ...

  • Miller Electric 456 CC - page 23

    OM-188 422 Page 19 3-10. Connecting Input Power ssb2.4* 1/94 – ST -801 523-B / ST -801 946 T ools Needed: 5/16 in Input Filter Board L1 =GND/PE Y Always connect grounding conductor first. Y T urn Off welding power source, and check voltage on input capacitors a c - cording to Section 5-3 before proceeding. Check input voltage available at site. R ...

  • Miller Electric 456 CC - page 24

    OM-188 422 Page 20 SECTION 4 – OPERA TION 4-1. Front Panel Controls 1 Power Switch . The fan motor is thermostatically controlled and only runs when cooling is needed. 2 V oltmeter (see Section 4-2) 3 Ammeter (see Section 4-2) 4 V/A (V oltage/Amperage) Adjust Control 5 V oltage/Amperage Control Switch For front panel control, place switch in Pane ...

  • Miller Electric 456 CC - page 25

    OM-188 422 Page 21 4-2. Meter Functions The meters display the actual weld output values for approximately three seconds after the arc is broken. NOTE Mode Meter Reading At Idle Lift-Arc T rigger Hold TIG (GT AW) VA Blank Preset Amps 85 TIG (GT AW) Blank Preset Amps VA 85 MIG (GMAW) Preset V olts Blank VA 24.5 Pulsed MIG (GMA W-P) Pulse Display Pul ...

  • Miller Electric 456 CC - page 26

    OM-188 422 Page 22 4-3. Mode Switch Settings The SMAW modes provide the Adaptive Hot Start  feature, which automatically increases the output amperage at the start of a weld should the start require it. This eliminates electrode sticking at arc start. NOTE Mode Output Control Lift-Arc T rigger Hold TIG (GT AW) Select: or Amp Requires: Control TI ...

  • Miller Electric 456 CC - page 27

    OM-188 422 Page 23 4-4. Lift-Arc TIG Procedure With Mode switch in the Lift-Arc TIG position, start an arc as follows: 1 TIG Electrode 2 W orkpiece T ouch tungsten electrode to work- piece at weld start point, hold electrode to workpiece for 1-2 seconds , and slowly lift electrode. An arc will form when electrode is lifted. Normal open-circuit volt ...

  • Miller Electric 456 CC - page 28

    OM-188 422 Page 24 SECTION 5 – MAINTENANCE & TROUBLESHOOTING 5-1. Routine Maintenance Y Disconnect power before maintaining. . Maintain more often during severe conditions. 3 Months Replace Damaged Or Unreadable Labels Replace Cracked T orch Body Repair Or Replace Cracked Cables Repair Or Replace Cracked Cables And Cords Clean And T ighten W ...

  • Miller Electric 456 CC - page 29

    OM-188 422 Page 25 5-3. Removing Case and Measuring Input Capacitor V oltage Turn Of f welding power source, an d disconnect input power . 1 Outside Handle Screws T o loosen top, remove two outside handle screws from both handles and all side bolts. 2 Interconnecting Board PC2 3 V oltmeter Measure the dc voltage across th e screw terminals on RC3 a ...

  • Miller Electric 456 CC - page 30

    OM-188 422 Page 26 5-4. V oltmeter/Ammeter Help Displays . Al l directions are in reference to th e front of the unit. All circuitry referred to is located inside the unit. 1 Help 1 Display Indicates a malfunction in the pri- mary power circuit. If this display is shown, contact a Factory Autho- rized Service Agent. 2 Help 2 Display Indicates a mal ...

  • Miller Electric 456 CC - page 31

    OM-188 422 Page 27 5-5. T roubleshooting T rouble Remedy No weld output; unit completely inop- erative. Place line disconnect switch in On position (see Section 3-10). Check and replace line fuse(s), if necessary , or reset circuit breaker (see Section 3-10). Check for proper input power connections (see Section 3-10). No weld output; meter display ...

  • Miller Electric 456 CC - page 32

    OM-188 422 Page 28 SECTION 6 – ELECTRICAL DIAGRAM Figure 6-1. Circuit Diagram For Welding Power Source ...

  • Miller Electric 456 CC - page 33

    OM-188 422 Page 29 192 795 ...

  • Miller Electric 456 CC - page 34

    OM-188 422 Page 30 SECTION 7 – P ARTS LIST . Hardware is common and not available unless listed. 802 261-C 1 2 9 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 31 32 33 39 40 41 42 4 44 45 46 48 49 50 46 51 53 54 58 59 62 63 64 65 4 PC1 PC2 3 66 4 5 6 7 8 30 34 35 36 37 38 36 43 47 60 61 10 52 55 56 57 67 802 261 Figure 7-1. Complete As ...

  • Miller Electric 456 CC - page 35

    OM-188 422 Page 31 Description Part No. Dia. Mkgs. Item No. Figure 7-1. Complete Assembly Quantity 1 187 234 COVER, top 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 195 585 HANDLE 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Miller Electric 456 CC - page 36

    OM-188 422 Page 32 Description Part No. Dia. Mkgs. Item No. Figure 7-1. Complete Assembly (Continued) Quantity 54 HD1 168 829 TRANSDUCER, current 1000A max 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 174 992 KNOB, pointer .840dia x .250 ID 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Miller Electric 456 CC - page 37

    OM-188 422 Page 33 Notes ...

  • Miller Electric 456 CC - page 38

    OM-188 422 Page 34 Notes ...

  • Miller Electric 456 CC - page 39

    Warranty Questions? Call 1-800-4-A-MILLER for your local Miller distributor. miller_warr 7/00 Y our distributor also gives you ... Service Y ou always get the fast, reliable response you need. Most replacement parts can be in your hands in 24 hours. Support Need fast answers to the tough welding questions? Contact your distributor . The expertise o ...

  • Miller Electric 456 CC - page 40

    PRINTED IN USA  2001 Miller Electric Mfg. Co. 1/01 Miller Elect ric Mfg. Co. An I l li noi s T ool W orks Company 1635 W est S pencer Street Applet on, W I 5 4914 USA International He adquarte rs – USA USA Phone: 920-735-4505 Auto-A t t ended USA & C anada F AX: 920-735-4134 Int ernational F AX: 920-735-4125 European Headquarte rs – Unit ...

Fabbricante Miller Electric Categoria Welder

I documenti che otteniamo dal fabbricante del dispositivoMiller Electric 456 CC possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Miller Electric
- manuali per l’uso 456 CC
- schede prodotto Miller Electric
- opuscoli
- o etichette energetiche Miller Electric 456 CC
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Miller Electric 456 CC.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Miller Electric 456 CC, manuali di manutenzione, brevi manuali o manuali utente Miller Electric 456 CC. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Miller Electric 456 CC.

Manuali per l’uso simili

Manuale completo del dispositivo Miller Electric 456 CC, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Miller Electric 456 CC dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Miller Electric 456 CC.

Il manuale per l’uso completo Miller Electric, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Miller Electric 456 CC - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Miller Electric 456 CC, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Miller Electric 456 CC che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Miller Electric 456 CC - che ci dovrebbe aiutare nei primi passi durante l'uso Miller Electric 456 CC
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Miller Electric 456 CC
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Miller Electric 456 CC in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Miller Electric 456 CC?

Utilizza il modulo sottostante

Se non hai risolto il problema con Miller Electric 456 CC con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Miller Electric 456 CC è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)