Italiano dropdown-ico

Manuale per l’uso Cisco Systems 2700

28 pagine 1.25 mb
Scarica

Vai alla pagina of 28

Summary
  • Cisco Systems 2700 - page 1

    Corporate Headquarters: © 20 05 Cisco Syst ems, Inc. All rights reserved. Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Cisco 2700 Series Wireless Location Appliance Deployment Guide This document pro vides conf iguration and deploymen t guidelines as well as troubleshootin g tips and answers to frequently asked techni ca ...

  • Cisco Systems 2700 - page 2

    2 Cisco 2700 Series Wireless Location Appliance Dep loyment Guide OL-8478-01 lightweight access points. Thi s appliance tracks an y W i-Fi de vice, in cluding W i-Fi clients, standards-based W i-Fi active RFID tags, rogue access points, and client s. It was designed with the follo wing requirements in mind: • Manageability—The same bro wser-bas ...

  • Cisco Systems 2700 - page 3

    3 Cisco 2700 Series Wireless Location Appliance Deployment Guide OL-8478-01 Calibr ation is the process whereb y sample signal strength measurements are physically tak en in the actual en vironments in which you wish to perform locatio n tracking as inputs to tune t he location tracking rather than u sing the canned or simulate d en vironment’ s ...

  • Cisco Systems 2700 - page 4

    4 Cisco 2700 Series Wireless Location Appliance Dep loyment Guide OL-8478-01 The follo wing Cisco wireless LAN controllers are a vailable. The follo wing Cisco Aironet access points are a v ailable. The Difference Between WCS with L ocation and the Lo cation Appliance WCS without the us e of the location appl iance supports on-demand or query-based ...

  • Cisco Systems 2700 - page 5

    5 Cisco 2700 Series Wireless Location Appliance Deployment Guide OL-8478-01 Figur e 2 Location Det ermin ation Note T o add the location appliance, the W CS version with lo cation must be installed. Y ou cannot add the location appliance to t he WCS base version. Additional Functionality with Location Appliance Figure 3 illustrates the scale and v ...

  • Cisco Systems 2700 - page 6

    6 Cisco 2700 Series Wireless Location Appliance Dep loyment Guide OL-8478-01 System Architecture Figure 3 Scale and V ariety of Devices System Architecture The location appliance integrates wi th Cisco's centralized wireless LAN architecture. The appliance sits out of the data path of the wireless LAN, working w ith both the WCS and the contro ...

  • Cisco Systems 2700 - page 7

    7 Cisco 2700 Series Wireless Location Appliance Deployment Guide OL-8478-01 Location-Based Services Overview Figur e 4 Syst em Archit ecture Access points can detect devices both on the channels wh ere they serv ice clients and on all other channels b y periodically scanni ng, while still pr ov id ing uninterrupted data access to t heir wireless cl ...

  • Cisco Systems 2700 - page 8

    8 Cisco 2700 Series Wireless Location Appliance Dep loyment Guide OL-8478-01 Deployment and Design Requirements Rogue clients are simp ly all client de vices that are associated to rogue access points. Asset tags are any v endors' 802.11-based RF ID tags with in range of inf rastructure access points. Deployment and Design Requirements Conside ...

  • Cisco Systems 2700 - page 9

    9 Cisco 2700 Series Wireless Location Appliance Deployment Guide OL-8478-01 Deployment and Design Re quirements • AIR-ANT -5145V -R • AIR-ANT -5160V -R Access Point Placement T o determine the optimum location of all de vices in the wireless LAN co verage areas, you need to consider the access point density and location. Ensure that no fewer th ...

  • Cisco Systems 2700 - page 10

    10 Cisco 2700 Series Wireless Location Appliance Dep loyment Guide OL-8478-01 Deployment and Design Requirements Figur e 6 Impro ved Location Accu r acy by Incr easing Density 3. In long and narro w cov erage areas, refrain from pl acing access points in a st raight line. Instead, attempt to stagger them such that each access point is more likely t ...

  • Cisco Systems 2700 - page 11

    11 Cisco 2700 Series Wireless Location Appliance Deployment Guide OL-8478-01 Deployment and Design Re quirements Figur e 8 Impro ved Location Accu rac y by Stagg erin g Ar ound P er i met er 5. Designing a location-a ware wireless LAN, while p lanning for v oice as well, is better done with a fe w things in mind. Most cu rrent wireless handse ts su ...

  • Cisco Systems 2700 - page 12

    12 Cisco 2700 Series Wireless Location Appliance Dep loyment Guide OL-8478-01 Deployment and Design Requirements the build ings that compri se that campus, and the floors of each buil ding constitute a single netw ork design. The location appl iance is set to poll the contr oll ers in that netw ork, as well as be configu red to synchronize with tha ...

  • Cisco Systems 2700 - page 13

    13 Cisco 2700 Series Wireless Location Appliance Deployment Guide OL-8478-01 Deployment and Design Re quirements Step 6 Check to enable the Maintain Aspect Ra tio check box. Enabling this check box causes the horizontal span of the campus to be 5000 feet and adjusts the v ertical span according to the image f ile’ s aspect ratio. Adjusting either ...

  • Cisco Systems 2700 - page 14

    14 Cisco 2700 Series Wireless Location Appliance Dep loyment Guide OL-8478-01 Deployment and Design Requirements Figur e 12 Repositioni ng Building High light ed in Blue Step 12 WCS is then returned to the campus image with the newly created b uilding highlighted in a green box.Click the green box (see Figure 13 ). Figur e 13 Newly Creat ed Buildi ...

  • Cisco Systems 2700 - page 15

    15 Cisco 2700 Series Wireless Location Appliance Deployment Guide OL-8478-01 Deployment and Design Re quirements Step 14 Enter the building’ s name , contact inf ormation , number of floors and basements , and dimension information. Click OK . WCS is returned to the Mon itor > Maps windo w . Step 15 Click the hy p er li nk associated with the ...

  • Cisco Systems 2700 - page 16

    16 Cisco 2700 Series Wireless Location Appliance Dep loyment Guide OL-8478-01 Deployment and Design Requirements Step 21 At the new floor ’ s image windo w (Monitor > Maps > [CampusName] > [Build ingName] > [FloorName]), go to the drop- do wn menu on the upper right and choose Add Access Poin ts . Click Go . Step 22 All access points ...

  • Cisco Systems 2700 - page 17

    17 Cisco 2700 Series Wireless Location Appliance Deployment Guide OL-8478-01 Deployment and Design Re quirements Creating and Applying Calibration Models If the provided RF models do not suf ficiently characterize the floor layout, you can create a calibration model that is applied to the floor and better r epresents the attenuation characteris tic ...

  • Cisco Systems 2700 - page 18

    18 Cisco 2700 Series Wireless Location Appliance Dep loyment Guide OL-8478-01 Deployment and Design Requirements Step 7 When the chosen floor map and acces s point locations are presented, a grid of dots indicates the locations where data collection for calibratio n is performed. Usin g these locations as g uidelines, position a wireless de vice in ...

  • Cisco Systems 2700 - page 19

    19 Cisco 2700 Series Wireless Location Appliance Deployment Guide OL-8478-01 Configuring th e Location Appliance Step 10 When all the raw data collection has been performed, the model must be compiled to allo w WCS and the location appliance to use the data for the understa nding of RF attenuation ch aracteristics. T o compute the collected data po ...

  • Cisco Systems 2700 - page 20

    20 Cisco 2700 Series Wireless Location Appliance Dep loyment Guide OL-8478-01 Configuring the Location App liance #service network restart 5. V erify that the new IP addressi ng works properly and that the location ap pliance has connecti vity back to the WCS by pi nging the WCS’ IP address. # ping [IP_Address] If IP connecti vity is verif ied be ...

  • Cisco Systems 2700 - page 21

    21 Cisco 2700 Series Wireless Location Appliance Deployment Guide OL-8478-01 Configuring th e Location Appliance Figure 1 9 Synchronizing Controllers Step 17 If the network diagram is prop erly synchronized, tw o green arrows appear under the Sync. Status col umn for each diagram. After synchronizing wi th the network d iagram, all floor maps and a ...

  • Cisco Systems 2700 - page 22

    22 Cisco 2700 Series Wireless Location Appliance Dep loyment Guide OL-8478-01 Location Appliance Maintenance Step 2 On the left choo se Administration and then click P olling Para meters . Step 3 Click to check the check boxes to the left of each desired polling parameter . Adjust the intervals if necessary and click Save . Note These settings gov ...

  • Cisco Systems 2700 - page 23

    23 Cisco 2700 Series Wireless Location Appliance Deployment Guide OL-8478-01 Troubleshooting Tips Q & A Restoring the Location Appliance T o restore a prev iously made backup, na vigate to Locate > Location Servers and click the hyperlink of the location appliance to be restored . Select the f ile to be restored from the dr op-do wn menu and ...

  • Cisco Systems 2700 - page 24

    24 Cisco 2700 Series Wireless Location Appliance Dep loyment Guide OL-8478-01 Troubl eshooting T ips Q & A A. By default, th e location appliance polls control l ers for de vice information e very 5-15 minu tes, depending on device type. The polling inte rv al can be altered, but if you have not waited for at least this polling interv al, devic ...

  • Cisco Systems 2700 - page 25

    25 Cisco 2700 Series Wireless Location Appliance Deployment Guide OL-8478-01 Troubleshooting Tips Q & A A. When searching for a client or tag, WCS searches in all av ailable location appliances. WCS reports the floor on which the tag is f ound, and history may sho w that it has been moving acro ss campuses reg ardless of whi ch controll er the ...

  • Cisco Systems 2700 - page 26

    26 Cisco 2700 Series Wireless Location Appliance Dep loyment Guide OL-8478-01 Troubl eshooting T ips Q & A A. The network load from location traff ic de pends on a num ber of factors: – ho w many de vices are present in a gi ven system – ho w man y contr ollers are present – what information th e location appliance is conf igured to poll ...

  • Cisco Systems 2700 - page 27

    27 Cisco 2700 Series Wireless Location Appliance Deployment Guide OL-8478-01 Troubleshooting Tips Q & A Q. Ho w long do W iFi tags last? A. T ag battery life is a f unction of specif ic device ba tt ery longe vity , as well as how often the y beacon or blink. The tags can last an ywhere from 100 days to a year or e ven longer . Some manufacture ...

  • Cisco Systems 2700 - page 28

    28 Cisco 2700 Series Wireless Location Appliance Dep loyment Guide OL-8478-01 Troubl eshooting T ips Q & A ...

Fabbricante Cisco Systems Categoria Network Router

I documenti che otteniamo dal fabbricante del dispositivoCisco Systems 2700 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Cisco Systems
- manuali per l’uso 2700
- schede prodotto Cisco Systems
- opuscoli
- o etichette energetiche Cisco Systems 2700
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Cisco Systems 2700.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Cisco Systems 2700, manuali di manutenzione, brevi manuali o manuali utente Cisco Systems 2700. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Cisco Systems 2700.

Manuali per l’uso simili

Manuale completo del dispositivo Cisco Systems 2700, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Cisco Systems 2700 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Cisco Systems 2700.

Il manuale per l’uso completo Cisco Systems, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Cisco Systems 2700 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Cisco Systems 2700, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Cisco Systems 2700 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Cisco Systems 2700 - che ci dovrebbe aiutare nei primi passi durante l'uso Cisco Systems 2700
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Cisco Systems 2700
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Cisco Systems 2700 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Cisco Systems 2700?

Utilizza il modulo sottostante

Se non hai risolto il problema con Cisco Systems 2700 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Cisco Systems 2700 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)