Italiano dropdown-ico

Manuale per l’uso Sharp FO-2150CM

26 pagine 0.37 mb
Scarica

Vai alla pagina of 26

Summary
  • Sharp FO-2150CM - page 1

    1 - 1 UX-2200CMU/CMC FO-2150CMU/CMC F ACSIMILE INK JET PRINTER UX-2200CM MODEL FO-2150CM No. 00ZU220CMUTME TECHNICAL MANUAL Parts marked with " " is important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set. This document has been published to ...

  • Sharp FO-2150CM - page 2

    UX-2200CMU/CMC FO-2150CMU/CMC – 1 – [1] Engine Specifications 1. Mechanism Resolution : 600 dpi x 600 dpi addressability Print Speed : 3 PPM draft text with black cartridge Print Swath : 8 inches Duty Cycle : Up to 500 pages per month maximum, 170 pages per month average Dimensions (approximate) : 350mm x 125mm x 60mm Weight (approximate) : 1.2 ...

  • Sharp FO-2150CM - page 3

    UX-2200CMU/CMC FO-2150CMU/CMC [4] Circuit description 1. General description The compact design of printer PWB is obtained by using 8 bit microprocessor(CPU) and ASIC in the printer control section. 2. Electrical System The PWB provides mechanical control for Ink Jet Printer . Figure 1 shows the interconnection of PWB and other electrical component ...

  • Sharp FO-2150CM - page 4

    UX-2200CMU/CMC FO-2150CMU/CMC 3. Electricai Overview The information in this section appears in a sequence relative to the system diagram in the following figure. 4. Power Supply Connector The mechanism requires two voltages (+5V and +24V). These two voltages supplied from CNPR T connector. 5. Host interface connector Connector CNPRT on the printer ...

  • Sharp FO-2150CM - page 5

    UX-2200CMU/CMC FO-2150CMU/CMC 7. Driver IC The paper motor and carriage motor require current that cannot be driven directly from ASIC chip. Motor driver IC provide the additional current and voltage capability . The driver IC (IC1 and IC2) located near the respective motor connector on the printer PWB also connect back to the ASIC. Two additional ...

  • Sharp FO-2150CM - page 6

    UX-2200CMU/CMC FO-2150CMU/CMC 9. Carriage Motor The ASIC controls the carriage motor , which is a stepping motor that connects via a 4-pin connector to CN2 on the printer PWB. 10. INK Cartridge Carriage The carriage connects via a flex circuit that plugs into the 32 pin connectors, CN3 and CN4 on the printer PWB. The ink cartridge contacts connect ...

  • Sharp FO-2150CM - page 7

    UX-2200CMU/CMC FO-2150CMU/CMC – 6 – 12. Home Position Sensor LEFT RIGHT CARRIAGE HOLDER A B C The home position of carriage is detected as a result of change of output of photointurrupter A which is caused due to shutting-off of optical path of photointerrupter A by the slit B . While the photointerrupter is shut off by the slit B, the output ( ...

  • Sharp FO-2150CM - page 8

    UX-2200CMU/CMC FO-2150CMU/CMC [5] Overall T rouble Shooting Of Printer PWB FRONT VIEW B C E Q1 FRONT VIEW BE C Q101 Figure 1 Figure 2 – 7 – NG NG • BOTH CARRIAGE MOTOR AND FEED MOTOR ARE NG. OPEN REPLACE F100 AND F101 +24V AT Q1-E (Figure 1) OK OK NG FUSE “F100” AND “F101 +24V AT Q1-C (Figure 1) +5V AT Q101-B (Figure 2) CHECK RESISTANCE ...

  • Sharp FO-2150CM - page 9

    UX-2200CMU/CMC FO-2150CMU/CMC CHECK WAVEFORMS IC2 ( 3,5,7,9 pin) (Figure 3) REPLACE PRINTER PWB FUSE “F101” Check the laser diode driver. OPEN OK OK OK CHECK WAVEFORMS IC2 ( 2,4,6,8 pin) (Figure 4) NG CHECK IC5 REPLACE PRINTER PWB REPLACE IC5 • FEED MOTOR IS NG (CARRIAGE MOTOR IS GOOD) REPLACE F101 NG OK OK CHECK IC2 REPLACE PRINTER PWB REPLA ...

  • Sharp FO-2150CM - page 10

    UX-2200CMU/CMC FO-2150CMU/CMC MISSING MANY NOZZLES CLEAN NOZZLES NG NG YES REPLACE ANOTHER CARTRIDGE NO • MISSING NOZZLES (RESULT OF CHECK PATTERN OR CLEAN NOZZLES CHECK +24 PATTERN CHECK IC AND CONNECTOR BY REFERING TO THE TABLE 1&2 CHECK THE SOLDER IC4, IC6 COMMON pin IC 5 82-89 pin IC4 1,4,40,41,43,44 pin IC6 1,4,40,41,43,44 pin OK OK CHEC ...

  • Sharp FO-2150CM - page 11

    UX-2200CMU/CMC FO-2150CMU/CMC [6]How to Decide the Number of the Wrong Nozzle FUNC + 6 + + “CLEAN NOZZLES” A B Nozzle 1 Nozzle 56 Horizontal lines on A and B correspond to nozzle #1,#2 .... #56 from left side to right side. If there are missing horizontal lines, you can decide the number of wrong nozzle from pattern A or B . Note) Don’t use t ...

  • Sharp FO-2150CM - page 12

    UX-2200CMU/CMC FO-2150CMU/CMC Nozzle# 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 IC 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 PIN 39 39 35 35 31 31 25 25 36 36 32 32 26 26 37 37 33 33 27 27 38 38 34 34 30 30 24 24 CN 3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4 3 4 PIN 9 28 10 27 11 26 12 25 13 2 ...

  • Sharp FO-2150CM - page 13

    UX-2200CMU/CMC FO-2150CMU/CMC 2ms / d CN1-2 CN1-3 CN1-4 CN1-5 CH1=50V DC P:10 T:1.92ms Stopped CH2=50V DC P:10 1/ T:520.8Hz CH3=50V DC P:10 CH4=50V DC P:10 T 1 2 3 4 G G G G G : 0V [7] W aveforms FEED MOTOR W A VEFORMS WHEN FEEDING P APER Figure 1 – 12 – ...

  • Sharp FO-2150CM - page 14

    UX-2200CMU/CMC FO-2150CMU/CMC CARRIAGE MOT OR W A VEFORMS – 13 – Figure 2 20s / d CN2-1 CN2-2 CN2-3 CN2-4 CH1=20V DC P:10 T:19.2¨s Stopped CH2=20V DC P:10 1/ T:52.08kHz CH3=20V DC P:10 CH4=20V DC P:10 T 1 2 3 4 When the cartridge holder is at the position of replacing cartridge. 1ms / d CN2-1 CN2-2 CN2-3 CN2-4 CH1=20V DC P:10 T:960¨s Stopped ...

  • Sharp FO-2150CM - page 15

    UX-2200CMU/CMC FO-2150CMU/CMC CARRIAGE MOTOR W A VEFORMS MEASURED FOR CHECKING OUT OF INK 2ms / d CN2-1 CN2-2 CN2-3 CN2-4 CH1=20V DC P:10 T:1.92¨ms Stopped CH2=20V DC P:10 1/ T:520.8Hz CH3=20V DC P:10 CH4=20V DC P:10 T 1 2 3 4 500s / d CN2-1 CN2-2 CN2-3 CN2-4 CH1=20V DC P:10 T:480¨s Stopped CH2=20V DC P:10 1/ T:2.083kHz CH3=20V DC P:10 CH4=20V DC ...

  • Sharp FO-2150CM - page 16

    UX-2200CMU/CMC FO-2150CMU/CMC Action Check the motor for binds,or loose motor pulley . T urn the printer off and disconnect CN2 from the system board.Check for motor pins shorted to the motor housing.If you find a pin shorted to the housing,replace the motor . If the failure remains,replace the system board. A noisy or chattering motor or a motor t ...

  • Sharp FO-2150CM - page 17

    UX-2200CMU/CMC FO-2150CMU/CMC FRU Envelope Guide Action Be sure the envelope guide has been turned to the envelope load position. Be sure the envelope guide is against the envelopes. Perform the ‘Paper Feed Service Check’on page 4. 1 FRU Maintenance Station Assembly Wiper Cap Action As the carrier moves to the right over the maintenance station ...

  • Sharp FO-2150CM - page 18

    UX-2200CMU/CMC FO-2150CMU/CMC FRU System Board Paper Feed Motor Drive T rain Assembly Auto Sheet Feeder Mid-Frame Asm Access Cover Asm End-of-Forms Flag and Spring End-of-Forms Sensor Action T urn the printer on and verify the paper feed motor activates. Be sure the end-of-form sensor lever is in the down position. T urn the printer off and disconn ...

  • Sharp FO-2150CM - page 19

    UX-2200CMU/CMC FO-2150CMU/CMC 5. Paper Path Service Check Examine the machine for the following before you being this service check: • Check the entire paper path for obstructions • Be sure the correct type of paper is being used. • Be sure the printer is installed on a flat surface. 6. Power Service Check FRU Large and Small Feed Rollers Sma ...

  • Sharp FO-2150CM - page 20

    UX-2200CMU/CMC FO-2150CMU/CMC – 19 – [9] IC Signal Name IC 8 : VHiTMP87PH47U (TMP87C807U) 1. Pin Assignment (T op View) 2. Block Diagram 34 35 36 37 38 39 40 41 42 43 44 22 21 20 19 18 17 16 15 14 13 12 33 32 31 30 29 28 27 26 25 24 23 P63 P62 P61 P60 N.C. VSS XOUT XIN RESET TEST P00 P14(PPG) P13(DVO) P12(INT2/TC1) P11(INT1) P10(INT0) P51 P50 P ...

  • Sharp FO-2150CM - page 21

    UX-2200CMU/CMC FO-2150CMU/CMC P07 to P00 I/O P17,P16 I/O P15(TC2) I/O(Input) P14(PPG) I/O(Output) P13(OVO) P12(INT2/TC1) I/O(Input) P1 1(INT1) P10(INT0) P22(XTOUT) I/O(Output) P21(XTIN) I/O(Input) P20(INT5/STOP) P51,P50 Output P67 to P60 I/O(Output) P77(HSO) I/O(Output) P76(HSCK) P75(SO) P74(SI) P73(SCK) I/O(I/O) P72(PWM/PDO) I/O(Output) P71(INT4) ...

  • Sharp FO-2150CM - page 22

    UX-2200CMU/CMC FO-2150CMU/CMC – 21 – IC 4 , 6 : VHil6451///-1 (L6451) 1. Pin Connection (T op View) 2. Block Diagram (case of 4 bit) 6 5 4 3 2 1 44 43 42 41 40 OUT 27 CHIP ENABLE COM 2 GND LOGIC SUPPLY IN D IN C IN B GND IN A COM 1 OUT 0 OUT 1 OUT 2 OUT 3 OUT 4 OUT 5 OUT 6 OUT 7 OUT 8 OUT 9 GND N.C. N.C. OUT 17 OUT 16 OUT 15 OUT 14 OUT 13 OUT 1 ...

  • Sharp FO-2150CM - page 23

    UX-2200CMU/CMC FO-2150CMU/CMC Name Function VDD 5V Logic Supply . GND Logic and Power Ground. OUT0 to OUT27 DMOS Output. CLAMP This pin has to be connected to the power supply voltage of the head resistors. Each of the output DMOS have their drain connected with the anode of a protection diode, all the cathodes of the protection diodes are connecte ...

  • Sharp FO-2150CM - page 24

    UX-2200CMU/CMC FO-2150CMU/CMC [10] Exploded V iew a a 26 14 37 45 54 56 56 55 11 15 16 18 17 36 25 905 10 24 21 20 19 4 1 32 3 13 2 31 28 INK SENSOR PWB Note : Since the parts circled by dots can not be supplied, change it as a unit 8 7 9 30 27 29 48 45 5 6 12 11 901 903 36 34 35 57 41 47 43 46 42 51 49 50 53 52 38 58 38 38 43 52 40 B5 B12 B12 B12 ...

  • Sharp FO-2150CM - page 25

    UX-2200CMU/CMC FO-2150CMU/CMC NO. P ARTS CODE PRICE RANK NEW MARK PA R T RANK DESCRIPTION [8] Printer unit 1 N C Frame chassis 2 N C Carrier cover(K) 3 N C Main shaft 4 N C Main shaft holder 5 N C Belt tension spring 6 N C Idler pulley holder 7 N C Carrier latch 8 N C Carrier latch SP 9 N C FFC plate 10 N C Main spring B 11 N C Timing belt 12 N C I ...

  • Sharp FO-2150CM - page 26

    UX-2200CMU/CMC FO-2150CMU/CMC No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher . SHARP CORPORA TION Communication Systems Group Quality & Reliability Control Cen ...

Fabbricante Sharp Categoria Fax Machine

I documenti che otteniamo dal fabbricante del dispositivoSharp FO-2150CM possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Sharp
- manuali per l’uso FO-2150CM
- schede prodotto Sharp
- opuscoli
- o etichette energetiche Sharp FO-2150CM
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Sharp FO-2150CM.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Sharp FO-2150CM, manuali di manutenzione, brevi manuali o manuali utente Sharp FO-2150CM. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Sharp FO-2150CM.

Manuali per l’uso simili

Manuale completo del dispositivo Sharp FO-2150CM, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Sharp FO-2150CM dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Sharp FO-2150CM.

Il manuale per l’uso completo Sharp, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Sharp FO-2150CM - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Sharp FO-2150CM, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Sharp FO-2150CM che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Sharp FO-2150CM - che ci dovrebbe aiutare nei primi passi durante l'uso Sharp FO-2150CM
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Sharp FO-2150CM
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Sharp FO-2150CM in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Sharp FO-2150CM?

Utilizza il modulo sottostante

Se non hai risolto il problema con Sharp FO-2150CM con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Sharp FO-2150CM è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)