-
Kraun KR.XM - page 1
www .kraun.it Router Ethernet/USB ADSL2/2+ User’s Manual Cod. KR.XM ...
-
Kraun KR.XM - page 2
www .kraun.it 2 User’s Manual Contents Package contents 3 1. Introduction 3 1.1 Product Overview 3 1.2 Main Features 3 1.3 Conventions 3 2. Hardware Installation Guide 3 2.1 The Front Panel 3 2.2 The Back Panel 4 2.3 Installation Environment 4 2.4 Hardware installation procedures 4 3. Quick Installation Guide 4 3.1 Configure PC 4 3.2 USB Configur ...
-
Kraun KR.XM - page 3
www .kraun.it 3 User’s Manual Package contents The following contents should be found in your box: • One KR.XM Router Ethernet/USB ADSL2/2+ • One AC power Adapter for KR.MX Router Ethernet/USB ADSL2/2+ • Quick Installation Guide • One RJ45 cable • One USB cable • Two RJ11 cables • One ADSL splitter • One Resource CD , including: ? ...
-
Kraun KR.XM - page 4
www .kraun.it 4 User’s Manual 2.2 The Back Panel Figure 2 2 • ON/OFF: The switch for the power. • POWER: The Power plug is where you will connect the power adapt- er. • RESET: There are two ways to reset the Router’s factory defaults. Method one: When the device is working, please press the reset but- ton of the Router, keep the reset but ...
-
Kraun KR.XM - page 5
www .kraun.it 5 User’s Manual Figure 3 3 Step 4: Configure the IP address as Figure 3 4 shows. After that, click OK. Figure 3 4 -> Note: You can configure the PC to get an IP address automatically, select “Obtain an IP address automatically” and “Obtain DNS server address automatically” in the screen above. Now, you can run the Ping co ...
-
Kraun KR.XM - page 6
www .kraun.it 6 User’s Manual Figure 3 7 Step 3: You will see Figure 3 8 as follow, please wait a moment. Figure 3 8 Step 4: After that, you will see Figure 3 9. Click Finish to complete the installation. Figure 3 9 -> Note: 1) All of the above settings are under windows XP. 2) If you want to pull out the USB device you must disconnect the net ...
-
Kraun KR.XM - page 7
www .kraun.it 7 User’s Manual Figure 3 13 Step 4: Configure the following options provided by your ISP: User- name, Password, VPI, VCI and Connection Type. Then click Next. Figure 3 14 Step 5: Click NEXT to finish the Quick Start. Figure 3 15 4. Software Configuration This User Guide recommends using the “Quick Installation Guide” for first-t ...
-
Kraun KR.XM - page 8
www .kraun.it 8 User’s Manual Figure 4 4 - ATM VC: ATM settings are used to connect to your ISP. Your ISP pro- vides VPI (Virtual Path Identifier), VCI (Virtual Channel Identifier) set- tings to you. In this Device, you can totally setup 8 VCs on different encapsulations, if you apply 8 different virtual circuits from your ISP. You need to activa ...
-
Kraun KR.XM - page 9
www .kraun.it 9 User’s Manual Figure 4 6 -> Note: Each IP address entered in the fields must be in the appropriate IP form, which is four IP octets separated by a dot (x.x.x.x), such as 192.168.1.100. The Router will not accept the IP address if it is not in this format. 3. PPPoA/PPPoE Select this option if your ISP requires you to use a PPPoE ...
-
Kraun KR.XM - page 10
www .kraun.it 10 User’s Manual Figure 4 9 - Router Local IP: These are the IP settings of the LAN interface for the device. These settings may be referred to as Private settings. You may change the LAN IP address if needed. The LAN IP address is private to your internal network and cannot be seen on the Internet. • IP Address: Enter the Router? ...
-
Kraun KR.XM - page 11
www .kraun.it 11 User’s Manual 4.4 Advanced Setup Choose “Advanced Setup”, you can see the next submenus: Figure 4 12 Click any of them, and you will be able to configure the corresponding function. 4.4.1 Firewall Choose “Advanced Setup -> Firewall” menu, and you will see the next screen (shown in Figure 4 13). Figure 4 13 - Firewall: ...
-
Kraun KR.XM - page 12
www .kraun.it 12 User’s Manual - DMZ Host IP Address: Enter the specified IP Address for DMZ host on the LAN side. 4.4.3.2. Virtual Server Choose “Advanced Setup->NAT->Virtual Server” in Figure 4 16, you can configure the Virtual Server in the next screen. The Virtual Server is the server or server(s) behind NAT (on the LAN), for exampl ...
-
Kraun KR.XM - page 13
www .kraun.it 13 User’s Manual This is useful when there are certain types of data you want to give high- er priority, such as voice data packets give higher priority than Web data packets. This option will provide better service of selected network traffic over various technologies. Figure 4 21 - QoS: Select this option to Activate/Deactivate th ...
-
Kraun KR.XM - page 14
www .kraun.it 14 User’s Manual Figure 4 23 - PVID: Each physical port has a default VID called PVID (Port VID). PVID is assigned to untagged frames or priority tagged frames (frames with null (0) VID) received on this port. 2. Define VLAN Group Click Define VLAN Group in Figure 4 22, you can define VLAN groups in the next screen (shown in Figure ...
-
Kraun KR.XM - page 15
www .kraun.it 15 User’s Manual - Application: Select the application for the ACL rule, and then you can access the Router through it. - Interface: Select the interface for access: LAN, WAN or Both. - Access Control of Listing: This displays the information about the ACL Rules. 4.5.2 Filter Choose “Access Management->Filter”, you can see th ...
-
Kraun KR.XM - page 16
www .kraun.it 16 User’s Manual Step 4: Select the Protocol as “TCP” and select the Unmatched rule as “Next”. Step 5: Finally, click the SAVE to save the entry. Step 6: Go to Step 2 to configure the next two rules: Block E-mail re- ceived by the IP address 192.168.1.7 on your local network; Make the PC with IP address 192.168.1.8 unable to ...
-
Kraun KR.XM - page 17
www .kraun.it 17 User’s Manual 4.5.2.3 Application Filter Select Application Filter as the Filter type (shown in Figure 4 30), then you can configure the filter rules based on application. Figure 4 30 - Filter Type Selection: Select the Application Filter for the next configu- ration. - Application Filter: Activate or deactivate the function. - I ...
-
Kraun KR.XM - page 18
www .kraun.it 18 User’s Manual 4.5.5 DDNS Choose “Access Management->DDNS”, you can configure the DDNS function in the screen (shown in Figure 4 34). The router offers a Dynamic Domain Name System (DDNS) feature. The feature lets you use a static host name with a dynamic IP address. User should type the host name, user name and password as ...
-
Kraun KR.XM - page 19
www .kraun.it 19 User’s Manual -> Note: The ADSL Router built-in some NTP Servers, when the Router con- nects to the Internet, the Router will get the system time automati- cally from the NTP Server. You can also configure the NTP Server address manually, and then the Router will get the time from the specific Server firstly. 2. PC’s Clock S ...
-
Kraun KR.XM - page 20
www .kraun.it 20 User’s Manual Figure 4 44 4.6.5 Diagnostic Choose “Maintenance->Diagnostic”, you can view the test results for the connectivity of the physical layer and protocol layer for both LAN and WAN sides in the screen (shown in Figure 4 45). Figure 4 45 4.7 Help Choose “Help”, you can view the help information for configuratio ...
-
Kraun KR.XM - page 21
www .kraun.it 21 User’s Manual ...
Hai una domanda su Kraun KR.XM?
Utilizza il modulo sottostante
Se non hai risolto il problema con Kraun KR.XM con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Kraun KR.XM è probabile che voglia condividere il modo di risolverlo.