-
Dell PCI3 - page 1
su pp or t.d el l . c om In st a l li n g Syst em B o ar d O p ti on s 8 -1 This c hapter describes ho w to inst all the following op tions: P eripheral Component Interconnect (PCI) e xpansion cards Sy stem m ...
-
Dell PCI3 - page 2
8 -2 In sta lla tio n a n d T r ou ble s ho ot ing G ui de The sy stem accommodates up to six expansion cards, including tw o 3 2-bit/33-MHz and four 64-bit/33MHz P CI e xpansion cards. ...
-
Dell PCI3 - page 3
su pp or t. d el l .c om In st a l li n g Syst em Bo ar d O p ti on s 8 -3 F ollow this general procedure to install an expansion card : ? ...
-
Dell PCI3 - page 4
8 -4 In sta lla tio n a n d T r ou ble s ho ot ing G ui de 3. Unlatc h the card guide as shown in Figur e 8-3. 4. Insert the expansion card into the e xpansion-card connector . If the expansion card is full-length, insert the fr ...
-
Dell PCI3 - page 5
su pp or t. d el l .c om In st a l li n g Syst em Bo ar d O p ti on s 8 -5 ! " #$ % 5. When the card is firmly seated in the connector , secure the card's mounting brac ket to the c hassis wit h the screw you removed in ...
-
Dell PCI3 - page 6
8 -6 In sta lla tio n a n d T r ou ble s ho ot ing G ui de F ollow this general procedure to remo ve an e xpansion card: 1 . R emo ve the computer co ver according to the instr uctions in “ Remo ving the Computer Cov er ” in Chapter 7 . ...
-
Dell PCI3 - page 7
su pp or t. d el l .c om In st a l li n g Syst em Bo ar d O p ti on s 8 -7 & ' ' When adding ...
-
Dell PCI3 - page 8
8 -8 In sta lla tio n a n d T r ou ble s ho ot ing G ui de 2. T o access the memor y m odule s oc kets on the sy stem board, rot ate the po wer supply as described in “ Rotating the P o wer Supply A w ay F rom t he Sy stem Board ” in Chapter 7 . 3. Determine the memor y module soc k ets in whic h you will install memor y mod- ules or replace ex ...
-
Dell PCI3 - page 9
su pp or t. d el l .c om In st a l li n g Syst em Bo ar d O p ti on s 8 -9 If a memor y module is already installed in the soc ket y ou want to use, y ou must remov e it. T o do so, f ollow the instr uctions in “ Remo ving a Memor y Module. ” Use the follo wing ...
-
Dell PCI3 - page 10
8 -1 0 In sta lla tio n a n d T r ou ble s ho ot ing G ui de - ' ' T o take adv ant age of fut ure options in speed and functionality , y ou can add a second ...
-
Dell PCI3 - page 11
su pp or t. d el l .c om In st a l li n g Syst em Bo ar d O p ti on s 8- 1 1 NO TE: Dell recommends that only a tec hnically kno wledgeable person perform t his procedure. 1 . Remo ve the computer co ver according to the instr uctions in “ Remo ving the Computer Cov er, ” in Chapter 7 . ? ...
-
Dell PCI3 - page 12
8 -1 2 In sta lla tio n a n d T r ou ble s ho ot ing G ui de # $ ! $ % !! ! $ ! ...
-
Dell PCI3 - page 13
su pp or t. d el l .c om In st a l li n g Syst em Bo ar d O p ti on s 8- 1 3 0 ' % 7 . Unpac k the new microprocessor . If any of the pins on the microprocessor appear ben t, see Chapter 1 0, “ Get ting Help, ” for ins ...
-
Dell PCI3 - page 14
8 -1 4 In sta lla tio n a n d T r ou ble s ho ot ing G ui de 9. Inst all the microprocessor c hip in the soc ket (see Figure 8-1 2). # ! ! !? ...
-
Dell PCI3 - page 15
su pp or t. d el l .c om In st a l li n g Syst em Bo ar d O p ti on s 8- 1 5 " 2 1 2. If you are adding a second microprocessor , disconnect the F AN1 connector and place the VRM in the soc ket (see Figure 8 -1 4). Make sure t ...
-
Dell PCI3 - page 16
8 -1 6 In sta lla tio n a n d T r ou ble s ho ot ing G ui de 1 3. Connect the F AN1 connector . 1 4. R eplace the air shroud. 1 5. Replace the computer co ver making sure that the shroud support holds the shroud in place . 1 6. R econnect y our computer and peripherals to their pow er sources, and t urn them on. 17 . P ress < F2 > to ent er t ...
-
Dell PCI3 - page 17
su pp or t. d el l .c om In st a l li n g Syst em Bo ar d O p ti on s 8 -1 7 The operating lif e of the bat ter y can e xtend up to 1 0 years. T he bat ter y may need replacing if an incorrect time or date is displa yed during the boot routine along with a message suc h as: Time -of-d ay no t se t - p lease run SETU P pro gram or Inva lid c onfig u ...
-
Dell PCI3 - page 18
8 -1 8 In sta lla tio n a n d T r ou ble s ho ot ing G ui de 4. Locate the bat ter y and r emove it. T he bat ter y is mounted in a soc k et labeled "BA TTER Y" (see Figure 8-1). " % ? ...
-
Dell PCI3 - page 19
su pp or t. d el l .c om In st a l li n g Syst em Bo ar d O p ti on s 8- 1 9 9. While in the Sy stem Setup program, r eset the c hassis intrusion detector , and then exit the S ystem Set up program. NO TE: If a set up password has been assigned b y someone else, cont act y our net work administrator for information on reset ting the c hassis intrus ...
-
Dell PCI3 - page 20
8 -2 0 In sta lla tio n a n d T r ou ble s ho ot ing G ui de ...
Hai una domanda su Dell PCI3?
Utilizza il modulo sottostante
Se non hai risolto il problema con Dell PCI3 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Dell PCI3 è probabile che voglia condividere il modo di risolverlo.