Italiano dropdown-ico

Manuale per l’uso Cabletron Systems 6C105

38 pagine 0.51 mb
Scarica

Vai alla pagina of 38

Summary
  • Cabletron Systems 6C105 - page 1

    6C105 Smar tSwitch 6000 Overview and Setup Guide 1 23 4 5 PS1 PS2 6C405 9032016-04 ...

  • Cabletron Systems 6C105 - page 2

    ...

  • Cabletron Systems 6C105 - page 3

    6C105 Overview and Setup Guide i NOTICE Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes ha ve been made. The hardware, firmware, or software described in this ...

  • Cabletron Systems 6C105 - page 4

    Notice ii 6C105 Overview and Setup Guide DOC NOTICE This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites ap ...

  • Cabletron Systems 6C105 - page 5

    Notice 6C105 Overview and Setup Guide iii CABLETRON SOFTWARE PROGRAM LICENSE 1. LICENSE . You have the right to use only the one (1) copy of the Program provided in this package subject to the terms and conditions of this License Agreement. Y ou may not copy , reproduce or transmit any part of the Program except as permitted by the Copyright Act of ...

  • Cabletron Systems 6C105 - page 6

    Notice iv 6C105 Overview and Setup Guide DECLARATION OF CONFORMITY Application of Council Directiv e(s): 89/336/EEC 73/23/EEC Manufacturer’ s Name: Cabletron Systems, Inc. Manufacturer’ s Address: 35 Industrial Way PO Box 5005 Rochester, NH 03867 European Representativ e Name: Mr. J. Solari European Representativ e Address: Cabletron Systems Li ...

  • Cabletron Systems 6C105 - page 7

    6C105 Overview and Setup Guide v CONTENTS CHAPTER 1 INTRODUCTION 1.1 Using This Guide ......................................................................... 1-1 1.2 Structure of This Guide................................................................ 1-1 1.3 Document Conventions ............................................................... 1 ...

  • Cabletron Systems 6C105 - page 8

    Contents vi 6C105 Overview and Setup Guide ...

  • Cabletron Systems 6C105 - page 9

    6C105 Overview and Setup Guide 1-1 CHAPTER 1 INTR ODUCTION W elcome to the Cabletron Systems 6C105 SmartSwitch 6000 Overview and Setup Guide . This guide e xplains how to set up and configure the Cabletron Systems 6C105 SmartSwitch 6000 chassis. 1.1 USING THIS GUIDE Read through this guide completely to familiarize yourself with its contents and t ...

  • Cabletron Systems 6C105 - page 10

    Chapter 1: Introduction 1-2 6C105 Overview and Setup Guide 1.3 DOCUMENT CON VENTIONS Throughout this guide the follo wing symbols are used to call attention to important information. 1.4 USING THE 6C105 MANUAL SET Other manuals hav e been dev eloped for the interf ace modules that can be installed in the 6C105 chassis. These manuals e xplain how to ...

  • Cabletron Systems 6C105 - page 11

    Getting Help 6C105 Overview and Setup Guide 1-3 1.5 GETTING HELP If you need additional support related to this de vice, or if you have an y questions, comments, or suggestions concerning this manual, contact the Cabletron Systems Global Call Center: Before calling the Cabletron Systems Global Call Center , hav e the follo wing information ready: ? ...

  • Cabletron Systems 6C105 - page 12

    Chapter 1: Introduction 1-4 6C105 Overview and Setup Guide 1.6 OVERVIEW The Cabletron Systems 6C105 chassis design provides fiv e 2.4-inch slots that can contain a v ariety of interface modules. The chassis supports redundant po wer supplies, LANVIEW Diagnostic LEDs, and is 19-inch rack mountable. All chassis components (power supplies, fan tray , ...

  • Cabletron Systems 6C105 - page 13

    Features 6C105 Overview and Setup Guide 1-5 1.7 FEATURES Redundant P ower Supply Modules The 6C105 supports two po wer supply modules which reside in the slots labeled PS1 and PS2. Each po wer supply module supports an ac input connector that allows each po wer supply to be connected to a separate ac power source. Cabletron Systems also of fers a p ...

  • Cabletron Systems 6C105 - page 14

    Chapter 1: Introduction 1-6 6C105 Overview and Setup Guide A uto-Ranging Po wer Supplies The 6C105 po wer supply modules automatically adjust to the input voltage and frequenc y . No additional adjustments are necessary . Hot Swapping T o reduce network downtime, the po wer supply modules are also hot swappable. This allows for the remov al of one ...

  • Cabletron Systems 6C105 - page 15

    6C105 Overview and Setup Guide 2-1 CHAPTER 2 INSTALLATION REQUIREMENTS AND SPECIFICATIONS This chapter describes the follo wing: • Site guidelines that must be met before installing a 6C105 into a rack or cabinet • 6C105 configuration guidelines • Operating specifications for the 6C105 enclosure and po wer supply modules 2.1 SITE GUIDELINES ...

  • Cabletron Systems 6C105 - page 16

    Chapter 2: Installation Requirements and Specifications 2-2 6C105 Overview and Setup Guide 2.2 CONFIGURATION GUIDELINES The 6C105 has 5 slots that accept interface modules. The slots are numbered 1 to 5 beginning from the left. There are two additional slots located on the far right of the chassis that are reserv ed for power supply modules. These ...

  • Cabletron Systems 6C105 - page 17

    Operating Specifications 6C105 Overview and Setup Guide 2-3 2.3.1 Physical Specifications The physical specifications for the 6C105 chassis, 6C205-1, 6C205-2, 6C205-3 po wer supply modules and the 6C405 fan tray module are as follo ws: 6C105 Chassis 6C205-1 P ower Supply 6C205-2 P ower Supply 6C205-3 P ower Supply 6C405 Fan T ra y Dimensions: 62 ...

  • Cabletron Systems 6C105 - page 18

    Chapter 2: Installation Requirements and Specifications 2-4 6C105 Overview and Setup Guide 2.3.2 P ower Suppl y Requirements The po wer supply requirements for the 6C205-1, 6C205-2 and 6C205-3 po wer supply modules are as follows: 6C205-1 A C P ower Supply 6C205-2 DC P ower Supply 6C205-3 A C P ower Supply 2.4 LEDs The follo wing sections describe ...

  • Cabletron Systems 6C105 - page 19

    LEDs 6C105 Overview and Setup Guide 2-5 Figure 2-1 P ower Supply LEDs T able 2-1 P ower Supply LED States and Their Definitions LED Name Color Status PWR (P ower) Green All outputs and input of the power supply are within regulation. Red Any output or input of the specific po wer supply is out of regulation. REDUND ANCY Green Redundancy is av ail ...

  • Cabletron Systems 6C105 - page 20

    Chapter 2: Installation Requirements and Specifications 2-6 6C105 Overview and Setup Guide 2.4.2 Fan T ray LED The follo wing table describes the different states of the fan tray LED and their definitions. Refer to Figure 2-2 for the location of the fan tray LED. Figure 2-2 Fan T ray LED T able 2-2 Fan T ray LED States and Their Definitions LED ...

  • Cabletron Systems 6C105 - page 21

    6C105 Overview and Setup Guide 3-1 CHAPTER 3 6C105 SETUP This chapter contains instructions on setting up the Cabletron Systems 6C105 chassis. A Phillips screwdri ver is needed to install the unit in a 19-inch equipment rack, to install the cable management bar , to secure the po wer supply module(s) and to remo ve and reinstall the fan tray . Refe ...

  • Cabletron Systems 6C105 - page 22

    Chapter 3: 6C105 Setup 3-2 6C105 Overview and Setup Guide 3.2 SETTING UP THE 6C105 The follo wing sections describe the procedures that must be followed to complete the installation of the 6C105. 3.2.1 Installation Order Once a suitable site has been chosen, the 6C105 can be installed. The chassis can be freestanding or rack mounted. It is recommen ...

  • Cabletron Systems 6C105 - page 23

    Setting Up the 6C105 6C105 Overview and Setup Guide 3-3 3.2.2 Installing the Cable Management Bar T o install the cable management bar, proceed as follo ws: 1. Remove the cable management bar from the shipping box. Ensure that there are four screws inside the bag with the cable management bar. 2. Refer to Figure 3-1 . Line up the two holes on each ...

  • Cabletron Systems 6C105 - page 24

    Chapter 3: 6C105 Setup 3-4 6C105 Overview and Setup Guide 3.2.3 Rack Mounting the 6C105 The 6C105 can be mounted in a standard 19-inch equipment rack. T wo people may be required to lift the chassis into place. The chassis is secured with ten scre ws, five on each side. Using the scre ws provided with the equipment rack, secure the 6C105 to the ra ...

  • Cabletron Systems 6C105 - page 25

    Setting Up the 6C105 6C105 Overview and Setup Guide 3-5 3.2.4 Attaching the Electr ostatic Discharge Wrist Strap The Electrostatic Discharge (ESD) Wrist Strap must be attached before handling the po wer supplies, fan tray , or modules for the 6C105. In addition, observe all precautions when handling these modules to pre vent damage from ESD. Place ...

  • Cabletron Systems 6C105 - page 26

    Chapter 3: 6C105 Setup 3-6 6C105 Overview and Setup Guide 3.2.5 Installing a P ower Suppl y Module Y ou must install at least one power supply in the 6C105 chassis. One po wer supply provides sufficient po wer for most module configurations but a second po wer supply can be installed to provide a redundant, load sharing po wer source. When two po ...

  • Cabletron Systems 6C105 - page 27

    Setting Up the 6C105 6C105 Overview and Setup Guide 3-7 4. Slide the power supply module into the slot labeled PS1 as follows: a. Hold the module by placing one hand on the handle located on the module front panel and using the other hand to support the body of the module. b. With the LED at the top of the power supply module, align the circuit car ...

  • Cabletron Systems 6C105 - page 28

    Chapter 3: 6C105 Setup 3-8 6C105 Overview and Setup Guide Figure 3-4 Installing the P ower Supply Module(s) After installation of the po wer supply modules is completed the 6C105 is ready to be po wered up; howe ver , Cabletron Systems recommends that installation of all modules for the 6C105 be completed before po wering up the 6C105. Refer to the ...

  • Cabletron Systems 6C105 - page 29

    Setting Up the 6C105 6C105 Overview and Setup Guide 3-9 3.2.6 Installing 6C105 Interface Modules The 6C105 Interface Modules can be installed in an y of the 5 slots that are av ailable. T o install a module, proceed as follows: 1. Remove the blank panel covering the slot in which the Interface Module will be installed. All other slots must remain c ...

  • Cabletron Systems 6C105 - page 30

    Chapter 3: 6C105 Setup 3-10 6C105 Overview and Setup Guide Figure 3-5 Installing a Module 1 2 3 45 PS1 PS2 Plastic Locking T ab Slot Number 2361-02 2159-01 Circuit Card Card Guides Metal Back-Panel Plastic Locking T ab Backplane Connector 12 14 13 COM CPU 34 56 78 91 0 11 12 15 16 6E252-17 Fast Enet 100 FDX RX TX 2X 4X 6X 8X 10X 12X 14X 16X ...

  • Cabletron Systems 6C105 - page 31

    P owering Up a 6C105 with A C P ower Supplies 6C105 Overview and Setup Guide 3-11 3.3 P OWERING UP A 6C105 WITH A C P OWER SUPPLIES T o power up a 6C105 with ac po wer supply modules proceed as follows: 1. Plug one end of the power cord (supplied with the power supply) into the ac power socket on the bottom of the power supply. 2. Plug the other en ...

  • Cabletron Systems 6C105 - page 32

    Chapter 3: 6C105 Setup 3-12 6C105 Overview and Setup Guide Figure 3-6 P ower Supply DC ON/OFF Switch and DC Input P ower Strip DC P ower Supply Requirement f or Each Supply Each DC po wer supply input requires either a 48 VDC or 60 VDC power source, rated at a minimum of 17 Amps. ONL Y QU ALIFIED PERSONNEL SHOULD PERFORM THESE INST ALLA TION PROCED ...

  • Cabletron Systems 6C105 - page 33

    P owering Up a 6C105 with DC P ower Supplies 6C105 Overview and Setup Guide 3-13 Installation Requirement Each DC po wer supply input requires either a 48 VDC or 60 VDC power source supplied by three 10 A WG (American W ire Gauge) copper wires. These wires must be terminated with either ring or spade terminals that accept a #6 scre w . 3.4.1 Connec ...

  • Cabletron Systems 6C105 - page 34

    Chapter 3: 6C105 Setup 3-14 6C105 Overview and Setup Guide If you experience an y problems during the installation of the 6C105, contact Cabletron Systems Global Call Center for assistance. 3.5 REMOVING AND REINSTALLING THE F AN T RAY The 6C105 is equipped at the factory with a remo vable fan tray that allo ws for easy periodic cleaning and/or repl ...

  • Cabletron Systems 6C105 - page 35

    Removing and Reinstalling the F an T ray 6C105 Overview and Setup Guide 3-15 Figure 3-8 Removing the F an T ray 3.5.2 Reinstalling the Fan T ray T o reinstall the fan tray , refer to Figure 3-9 and proceed as follows: 1. Locate the ESD wrist strap shipped with the 6C105. Attach the ESD wrist strap to your wrist and plug the cable from the ESD wrist ...

  • Cabletron Systems 6C105 - page 36

    Chapter 3: 6C105 Setup 3-16 6C105 Overview and Setup Guide 4. Slide the fan tray forward until the faceplate of the tray is flush with the face of the 6C105. If there is any strong resistance, remove the fan tray and reinsert it. 5. Once the tray is in place, tighten the slotted screws with a screwdriver to secure the tray to the 6C105. 6. When the ...

  • Cabletron Systems 6C105 - page 37

    Removing and Reinstalling the F an T ray 6C105 Overview and Setup Guide 3-17 Figure 3-9 Reinstalling the Fan T ray Slot Guides Slotted Screws (2) 1 23 4 5 PS1 PS2 2016_08 6C405 ...

  • Cabletron Systems 6C105 - page 38

    Chapter 3: 6C105 Setup 3-18 6C105 Overview and Setup Guide ...

Fabbricante Cabletron Systems Categoria Switch

I documenti che otteniamo dal fabbricante del dispositivoCabletron Systems 6C105 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Cabletron Systems
- manuali per l’uso 6C105
- schede prodotto Cabletron Systems
- opuscoli
- o etichette energetiche Cabletron Systems 6C105
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Cabletron Systems 6C105.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Cabletron Systems 6C105, manuali di manutenzione, brevi manuali o manuali utente Cabletron Systems 6C105. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Cabletron Systems 6C105.

Manuali per l’uso simili

Manuale completo del dispositivo Cabletron Systems 6C105, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Cabletron Systems 6C105 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Cabletron Systems 6C105.

Il manuale per l’uso completo Cabletron Systems, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Cabletron Systems 6C105 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Cabletron Systems 6C105, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Cabletron Systems 6C105 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Cabletron Systems 6C105 - che ci dovrebbe aiutare nei primi passi durante l'uso Cabletron Systems 6C105
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Cabletron Systems 6C105
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Cabletron Systems 6C105 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Cabletron Systems 6C105?

Utilizza il modulo sottostante

Se non hai risolto il problema con Cabletron Systems 6C105 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Cabletron Systems 6C105 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)