-
Generac Power Systems 004917-4 - page 1
Installation and Owner’ s Man ual DEADL Y EXHAUST FUMES. OUTDOOR INST ALLA TION ONL Y!! D ANGER This manual should remain with the unit. Liquid-cooled, Prepac kaged Standb y Generators Model Number 004917-4 27 kW NG, 30 kW LP V apor Not intended for use in life-support applications. ! ! ...
-
Generac Power Systems 004917-4 - page 2
Generac ® Pow er Systems, Inc. I NTRODUCTION Thank you for purchasing this model of the standby generator set product line by Generac P ower Systems. Every effort was expended to make sure that the information and instructions in this manual are both accurate and current at the time the manual was writ- ten. However , the manufacturer reserves the ...
-
Generac Power Systems 004917-4 - page 3
T able of Contents QUIET SOURCE ™ Liquid-cooled 30 kW Generators Generac ® Pow er Systems, Inc. 1 INTRODUCTION ................................................ IFC SAFETY RULES .................................................... 2 Section 1 — GENERAL INFORMA TION ............4 1.1 Generator .................................................... ...
-
Generac Power Systems 004917-4 - page 4
2 Generac ® Pow er Systems, Inc. Study these SAFETY RULES carefully befor e installing, operating or servicing this equipment. Become familiar with this Owner’ s Manual and with the unit. The gen- erator can operate safely , efficiently and reliably only if it is properly installed, operated and maintained. Many accidents are caused by failing t ...
-
Generac Power Systems 004917-4 - page 5
Generac ® Pow er Systems, Inc. 3 • Inspect the generator regularly , and promptly repair or replace all worn, damaged or defective parts using only factory-approved parts. • Before performing any maintenance on the generator , disconnect its battery cables to prevent accidental start -up. Disconnect the cable from the battery post indicated by ...
-
Generac Power Systems 004917-4 - page 6
4 Generac ® Pow er Systems, Inc. 1.1 GEN ER A T OR This equipment is a liquid- cooled, engine - driven gen- erator set. The generator is designed to supply elec- trical power that operates critical electrical loads during utility power failure. The unit has been facto- ry-installed in a weather resistant, all aluminum enclosure and is intended for ...
-
Generac Power Systems 004917-4 - page 7
Generac ® Pow er Systems, Inc. 5 1.6 GEN ER A T OR F U EL SY S TEM The unit has been factory tested and adjusted using a natural gas fuel system. If propane (LP) gas is neces- sary . Refer to Section 1.12, Reconfiguring the F uel System. F uel pressure for a natural gas set up should be five inches to 14 inches of water column (0.18 to 0.5 psi) at ...
-
Generac Power Systems 004917-4 - page 8
6 Generac ® Pow er Systems, Inc. Figure 1.6 - Low Coolant Level Sensor 1.7 .4 O VERSPEED SH UTDOWN The engine control board receives AC frequency sig- nals from an engine run winding in the alternator . Should AC frequency exceed about 72 Hertz for three seconds or 75 Hertz instantaneously , the engine shuts down and the overspeed LED turns on. Sh ...
-
Generac Power Systems 004917-4 - page 9
1.1 0 SP ECIF ICA TIONS 1.1 0.1 GEN ER A T OR SP ECIF ICA TIONS 1.1 0.2 ENGI N E SP E CI F ICA TIONS Make ......................................................................................F ord Displacement ..................................................................3.0 liters Cylinder Arrangement ......................................... ...
-
Generac Power Systems 004917-4 - page 10
8 Generac ® Pow er Systems, Inc. NOTE: P ort 1 is for NG only and P ort 2 is for LP vapor only . No provision for dual fuel has been made. Serious injury or damage may occur if not con- figured pr operly . Please consult an authorized Generac Service Dealer with any questions. 1.1 3 T ORQU E SP ECIF ICA TIONS Cylinder Head ........................ ...
-
Generac Power Systems 004917-4 - page 11
Generac ® Pow er Systems, Inc. 9 Only qualified, competent installation contractors or electricians thoroughly familiar with applicable codes, standards and regulations should install this standby electric power system. The installation must comply strictly with all codes, standards and regula- tions pertaining to the installation. After the syste ...
-
Generac Power Systems 004917-4 - page 12
10 Generac ® Pow er Systems, Inc. • Allows the LOAD circuits to be connected to only one power supply at a time. • Prevents electrical backfeed between the generator and the UTILITY power circuits. Both the ST ANDBY and the UTILITY power supplies to the transfer switch are protected against overload by a main line circuit breaker . Figure 2.1 ...
-
Generac Power Systems 004917-4 - page 13
Generac ® Pow er Systems, Inc. 11 Failure to connect the generator neutral pr op- erly will result in unbalanced line-to-neutral voltages. Resulting high voltages will cause equipment damage. 2.9 TR ANSF ER SWIT CH SIGNAL CO N N EC T I O N S 2.9.1 P RE-P ACKAGED A TS If the generator is to be installed with a pre -packaged (non- control board base ...
-
Generac Power Systems 004917-4 - page 14
12 Generac ® Pow er Systems, Inc. • Spilled electrolyte is to be washed down with an acid-neutralizing agent. A common practice is to use a solution of one pound (500 grams) bicarbon- ate of soda to one gallon (4 liters) of water . The bicarbonate of soda solution is to be added until the evidence of reaction (foaming) has ceased. The resulting ...
-
Generac Power Systems 004917-4 - page 15
Generac ® Pow er Systems, Inc. 13 2.1 1.7 ELECTRICAL SY STEM Make sure the generator is properly connected to an approved earth ground and/or ground rod. Make sure the generator battery is fully charged, properly installed and interconnected, and ready for use. Check to ensure that there are no loose electrical con- nections. Restrain any loose wi ...
-
Generac Power Systems 004917-4 - page 16
14 Generac ® Pow er Systems, Inc. 3.2.2 F AU L T IN DICA T OR LED This LED goes ON when one or more of the following engine faults occurs and when engine shuts down. • Low Oil Pressure • Overcrank • Low Battery • Overspeed/RPM Sensor Loss • High Coolant T emperature/Low Coolant Level See Section 1.7 for further explanation of engine pro- ...
-
Generac Power Systems 004917-4 - page 17
Generac ® Pow er Systems, Inc. 15 Section 3 - Operation QUIET SOURCE ™ Liquid-cooled 30 kW Generators 5. Reduce load to 3/4, 1/2, 1/4 and no load. Decrease the stability pot if there is instability at any load point. 6. Adjust differential pot to make the recovery to load changes even faster and minimize load change undershoot and overshoot. If ...
-
Generac Power Systems 004917-4 - page 18
16 Generac ® Pow er Systems, Inc. 4.1 MAI NTENANCE P ER FOR M ED B Y AUTHOR IZED SERVICE F ACILITI ES A. EVER Y THR EE MONTHS 1. Check battery state of charge and condition. 2. Inspect and test fuel system. 3. Check transfer switch. 4. Inspect exhaust system. 5. Check engine ignition system. 6. Check fan belts. B. ONCE EVER Y SIX MONTHS 1. T est E ...
-
Generac Power Systems 004917-4 - page 19
Generac ® Pow er Systems, Inc. 17 4.4.3 ENGI NE COOLANT Check coolant level in coolant recovery bottle. See Specifications, Section 1.10. • Add recommended coolant mixture as necessary . • P eriodically remove radiator pressure cap to make sure the coolant recovery system is functioning properly . Coolant should be at bottom of radiator filler ...
-
Generac Power Systems 004917-4 - page 20
18 Generac ® Pow er Systems, Inc. 7. Start engine and check for oil leaks. Figure 4.2 - Oil Filter 4.5.1 1 CHANGI NG TH E ENGI NE AI R CLEAN ER T o replace the engine air cleaner , (part number 059402), remove the air cleaner cover and replace the air filter making sure it is positioned properly before reattaching the cover (Figure 4.3). Figure 4. ...
-
Generac Power Systems 004917-4 - page 21
Generac ® Pow er Systems, Inc. 19 4.6.2 BA TTER Y All lead-acid storage batteries discharge when not in use. Refer to specific instructions and warnings that accompany the battery . If such information is not available, observe the following precautions when handling a battery: • DO NOT use jumper cables and a booster battery to crank or start t ...
-
Generac Power Systems 004917-4 - page 22
20 Generac ® Pow er Systems, Inc. Section 4 — Maintenance QUIET SOURCE ™ Liquid-cooled 30 kW Generators 4.7 S CH EDU LED MAI NTENANCE F ollowing is a recommended maintenance schedule for Generac small standby and residential generator sets. The established intervals in the schedule are the maximum recommended when the unit is used in an averag ...
-
Generac Power Systems 004917-4 - page 23
Generac ® Pow er Systems, Inc. 21 Section 4 — Maintenance QUIET SOURCE ™ Liquid-cooled 30 kW Generators Maintenance Level 1 Level 2 Level 3 Level 4 T asks Recom- T ask Required T ask Required T ask T ask mended Comp . to be done Comp. to be done Comp . Required Comp . to be done (Date- 3 months/ (Date- Semi- (Date- to be done (Date- monthly In ...
-
Generac Power Systems 004917-4 - page 24
22 Generac ® Pow er Systems, Inc. Section 4 — Maintenance QUIET SOURCE ™ Liquid-cooled 30 kW Generators Maintenance Level 1 Level 2 Level 3 Level 4 T asks Recom- T ask Required T ask Required T ask T ask mended Comp . to be done Comp. to be done Comp . Required Comp . to be done (Date- 3 months/ (Date- Semi- (Date- to be done (Date- monthly In ...
-
Generac Power Systems 004917-4 - page 25
Generac ® Pow er Systems, Inc. 23 Section 5 — T roubleshooting QUIET SOURCE ™ Liquid-cooled 30 kW Generators TROU B LE SHOO TI NG POI NTS P ROBLEM CAUSE CORR E CTION Engine won’t crank. 1. 15 amp fuse blown. 1. Replace fuse . 2. Loose or corroded or defectiv e 2. Tighten, clean or replace batter y cables . batter y cables as necessary . 3. D ...
-
Generac Power Systems 004917-4 - page 26
BRUSH ASSEMLY ( GENERATOR ) A U T O MATI C V O LTA G E RE GU LAT OR BULKHEAD CONNECTOR 1 ( ENGINE ) CIRCUIT BREAKER ( EXCITATION ) FUSE, BAT. POWER ( 15A AGC TYPE ) CIRCUIT BREAKER ( OUTPUT ) DIODE [ FIELD BOOST ] BATTERY C HAR G E R B C 1 - F1 - D1 - C B2 - C B1 - AVR - BA - B /C - LE G END : NE U TRAL BL OCK TERMINAL BL OC K 1 TRANSFORMER 1 ( 56 ...
-
Generac Power Systems 004917-4 - page 27
Generac ® Pow er Systems, Inc. 25 LEGEND [ CONT. ]: J -2 - L OS - S M - J B - WL S - H C T - J -1 - IM - I C - ELE C . GO VERN O R A C T U AT OR GROUND ( SENSING/LOW AMP ) GROUND ( POWER/HIGH AMP ) D. C . C HAR G E ALTERNAT OR S TARTER CO NTA C T OR CONNECTOR 1 ( ENGINE ) DRIVER ELE C . GO VERN OR F U EL SO LEN O I D 12VD C BATTER Y DE G - G ND1 - ...
-
Generac Power Systems 004917-4 - page 28
26 Generac ® Pow er Systems, Inc. Section 6 - Electrical Data QUIET SOURCE ™ Liquid-cooled 30 kW Generators Electrical Schematic — Engine — Drawing No. 0E6200-B A U T O MATI C V O LTA G E RE GU LAT OR BRUSH ASSEMLY ( GENERATOR ) CIRCUIT BREAKER ( EXCITATION ) DI S PLA C ED PHA S E EX C ITATI ON DPE - ALTERNAT O R S TAT OR ALTERNAT O R R O T ...
-
Generac Power Systems 004917-4 - page 29
Generac ® Pow er Systems, Inc. 27 Section 6 - Electrical Data QUIET SOURCE ™ Liquid-cooled 30 kW Generators Electrical Schematic — Engine — Drawing No. 0E6200-B SC - I C - IM - L OS - S M - WL S - LEGEND [ CONT. ]: CONNECTOR (C1) SWITCH , HIGH COOLANT TEM P C RANKIN G CO NTA C T OR D. C . C HAR G E ALTERNAT OR CONNECTOR 1 ( ENGINE ) DRIVER E ...
-
Generac Power Systems 004917-4 - page 30
...
-
Generac Power Systems 004917-4 - page 31
...
-
Generac Power Systems 004917-4 - page 32
30 Generac ® Pow er Systems, Inc. ...
-
Generac Power Systems 004917-4 - page 33
Generac ® Pow er Systems, Inc. 31 ITEM P ART NO . QTY . DESCRIPTION 1 0E8418 1 DUCT INT AKE MID AL 2 0E8414 1 DUCT DISCHARGE RH AL 3 0E8413 1 DUCT DISCHARGE LH AL 4 0C2454 62 SCREW TH-FRM M6-1 X 16 N W A Z/JS 5 0E8402 1 BAFFLE REAR BOTT OM 6 0E5902 1 POST CORNER LH REAR HSB AL 7 0E5903 1 POST CORNER RH REAR HSB AL 8 0E8387 1 BAFFLE REAR T OP 9 0E5 ...
-
Generac Power Systems 004917-4 - page 34
32 Generac ® Pow er Systems, Inc. Section 7 - Exploded Views and P arts QUIET SOURCE ™ Liquid-cooled 30 kW Generators Control Panel — Drawing No. 0E7 11 8-J ...
-
Generac Power Systems 004917-4 - page 35
Generac ® Pow er Systems, Inc. 33 ITEM P ART NO . QTY . DESCRIPTION 1 0E7195 1 CONTROL BO X HSB 2 0E7196 1 CO VER FR ONT P ANEL HSB 3 0E7197 1 CO VER TOP P ANEL HSB 4 0E7193 1 DECAL W ARNINGS HSB 5 0E7194 1 DECAL CONTROLS HSB 6 0E4494 1 SWITCH ROC DPDT ON-OFF-ON 7 082573 1 SWITCH R OCKER DPST 125V SPD 8 032300 2 HOLDER FUSE 9 022676 1 FUSE 15A X A ...
-
Generac Power Systems 004917-4 - page 36
38 11 85 ...
-
Generac Power Systems 004917-4 - page 37
ITEM P ART NO . QTY . DESCRIPTION 1 0E6202 1 ENGINE 3.0L FORD (RD) (MAKE) 2 0E8824 2 ST AMPING ENG FOO T 3.0L FORD 3 0E8963 1 PULLEY CRANKSHAFT 3.0L FORD RD 4 0E9020 1 BRA CKET DC AL T 3.0L FORD 5 0A1232 1 D .C. AL TERNA T OR ASSY 6 0A7801B 1 PULLEY POL Y -V 82 OD . 7 0A5610 1 BRA CKET AL TERNA T OR 8 0E6308 1 PULLEY W A TERPUMP 3.0L FORD (RD) 9 ** ...
-
Generac Power Systems 004917-4 - page 38
E N G INE 5 "A " 12 ...
-
Generac Power Systems 004917-4 - page 39
ITEM P ART NO . QTY . DESCRIPTION 1 0E9947 1 RADIA TOR R-IN,L-OUT 658X489X49 2 0E6340 1 VENTURI 3.0L FORD HSB 3 0E8531 2 SIDE SUPPORT RADIA T OR HSB 4 0E6398 1 TUBE LOWER RAD 3.0L FORD HSB 5 0E6397 1 HOSE UPPER RAD 3.0LFORD HSB 6 080713 1 BRACKET COOLANT T ANK 7 076749 1 T ANK COOLANT RECO VER Y 8 049814 4 SCREW HHC M10-1.5 X 25 G8.8 9 022131 8 W A ...
-
Generac Power Systems 004917-4 - page 40
38 Generac ® Pow er Systems, Inc. 28 "B " 3 1 10 16 4 2 17 5 9 1 7 6 29 3 2 30 11 29 15 8 3 6 3 33 29 14 ...
-
Generac Power Systems 004917-4 - page 41
Generac ® Pow er Systems, Inc. 39 ITEM P ART NO . QTY . DESCRIPTION 1 * --------- 1 WELDMENT MOUNTING BASE 2 075580 1 FLANGE FUEL INLET 3 0E7691 1 ASSY REGULA TOR 3.0L NG OR LPV 4 039253 2 SCREW HHC M8-1.25 X 20 G8.8 5 022145 2 W ASHER FLA T 5/16 ZINC 6 022129 4 W ASHER LOCK M8-5/16 7 045771 2 NUT HEX M8-1.25 G8 YEL CHR 8 042907 2 SCREW HHC M8-1.2 ...
-
Generac Power Systems 004917-4 - page 42
40 Generac ® Pow er Systems, Inc. 3 ...
-
Generac Power Systems 004917-4 - page 43
Generac ® Pow er Systems, Inc. 41 ITEM P ART NO . QTY . DESCRIPTION 1 0F1659A 1 RO T OR 390 15KW 1P DIRECT HSB (2.5L FORD) 0F1657A 1 RO T OR 390 20KW 1P DIRECT HSB (2.5L FORD) 0F1655A 1 RO T OR 390 25KW 1P DIRECT HSB (2.5L FORD) 0F5073A 1 RO T OR 390__30AD1 HSB TECUM 0E7413A 1 RTR 390 40KW 1P DIRECT HSB 2 0F1660A 1 STR 390 15AD HSB (382MM LONG) (2 ...
-
Generac Power Systems 004917-4 - page 44
ITEM P ART NO . QTY . DESCRIPTION 1 0F0738 1 MUFFLER 7"X9"-(2)2"IN/2.5"OUT 2 0F6258 1 PIPE MUFFLER OUT 3 044149 2 GASKET EXHA UST RING 4 0F1008 1 EXHA UST PIPE LH 3.0L HSB 5 0F1009 1 EXHA UST PIPE RH 3.0L HSB 6 039288 1 SCREW HHC M8-1.25 X 55 G8.8 7 0E5914 1 BRA CKET MUFFLER 3.0L FORD HSB 8 0E8726 2 STRAP MUFFLER 9 0E0170 2 EXHA ...
-
Generac Power Systems 004917-4 - page 45
Generac ® Pow er Systems, Inc. 43 ITEM P ART NO . QTY . DESCRIPTION 1 0E5193 1 PLA TE AIR CLEANER AD APTER 2 0E8200 1 TUBE AIR INT AKE 3.0L FORD 3 0E8201 1 BRA CKET AIR INT AKE 3.0L FORD 4 036434 1 BOL T U 5/16-18 X 2.09 5 0E0519A 1 AD APTER CARBURET OR W/PVC CONN 6 0C8127 1 ELEMENT AIR CLEANER 7 0A5547 1 CO VER - AIR CLEANER 8 062974 1 STUD TH 1/ ...
-
Generac Power Systems 004917-4 - page 46
44 Generac ® Pow er Systems, Inc. Section 8 — Installation Diagram QUIET SOURCE ™ Liquid-cooled 30 kW Generators Installation Diagram — Drawing No. 0E8696 ...
-
Generac Power Systems 004917-4 - page 47
Generac ® Pow er Systems, Inc. 45 Section 9 — Notes QUIET SOURCE ™ Liquid-cooled 30 kW Generators ...
-
Generac Power Systems 004917-4 - page 48
Part No. 0F5546 ...
Hai una domanda su Generac Power Systems 004917-4?
Utilizza il modulo sottostante
Se non hai risolto il problema con Generac Power Systems 004917-4 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Generac Power Systems 004917-4 è probabile che voglia condividere il modo di risolverlo.