Manuale per l’uso Black Box IC483A

13 pagine 0.47 mb
Scarica

Vai alla pagina of 13

Summary
  • Black Box IC483A - page 1

    Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500 ) FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746 Mailing address: Black Box Corporation , 1000 Park Drive, Lawrence, PA 15055-1018 Web site: www.blackbox.com • E-mail: info@blackbox.com CUSTOMER SUPPORT INFORMATION NO VEMBER ...

  • Black Box IC483A - page 2

    FEDERAL COMMUNICA TIONS COMMISSION AND CANADIAN DEP ARTMENT OF COMMUNICA TIONS RADIO FREQUENCY INTERFERENCE ST A TEMENTS This equipment generates, uses, and can radiate radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio communication. I ...

  • Black Box IC483A - page 3

    V .35 ↔ RS-422 INTERF ACE CONVER TER TRADEMARKS USED IN THIS MANUAL Any trademarks mentioned in this manual are acknowledged to be the pr oper ty of the trademark owners ...

  • Black Box IC483A - page 4

    CONTENTS 3 Contents Chapter Page 1. SPECIFICA TIONS ......................................................................................................................................4 2. INTRODUCTION ......................................................................................................................................5 3. INST AL ...

  • Black Box IC483A - page 5

    V .35 ↔ RS422 INTERF ACE CONVER TER 4 1. Specifications Speed — Up to 2.5 Mbps Maximum T ransmission Rate — Approximately 2.455 Mbps Interface — RS-422, V .35 Connectors — IC481A-R2: RS-422: (1) DB37 female (pinned to RS-449 specifications); V .35: (1) male 34-pin “M” block IC483A: RS-422: (1) DB37 female (pinned to RS-449 specificati ...

  • Black Box IC483A - page 6

    CHAPTER 2: Introduction 5 2. Introduction The V .35 ↔ RS-422 Inter face Converter comes in both 115-V AC (IC483A) and 230-V AC (IC483AE) standalone units. A card version (IC483C) is available for rackmounting. The rack (RM060) is switch-selectable for either 115-V AC or 230-V AC operation. The V .35 ↔ RS-422 Inter face Converter provides bidire ...

  • Black Box IC483A - page 7

    V .35 ↔ RS422 INTERF ACE CONVER TER 6 3. Installation 3.1 DIP Shunt Settings The V .35 ↔ RS-422 Inter face Converter has two jumper selectable configurations determined by DIP shunt settings located inside the unit on the printed circuit board. One configuration is for connecting RS-422 DTE to V .35 DCE. The second configuration is for connecti ...

  • Black Box IC483A - page 8

    CHAPTER 3: Installation 7 T o install the V .35 ↔ RS-422 Inter face Converter , follow these steps and refer to Figures 3-1 and 3-2. 1. Set jumper XW6 to V .35 side when configuring the V .35 side of the unit as DTE. Set XW6 to the 422 side when configuring the RS422 side of the unit as DTE. Jumper XW6 affects only the front panel LEDs. 2 & 3 ...

  • Black Box IC483A - page 9

    V .35 ↔ RS422 INTERF ACE CONVER TER 8 3.2 LEDs The V .35 ↔ RS-422 Inter face Converter is equipped with ten LED indicators located on the front panel. The row of type above the LEDs indicates the uses of the LEDs for a RS422 DTE/V .35 DCE configuration. The row of type below the LEDs indicates the uses of the LEDs for a V .35DTE/RS422 DCE confi ...

  • Black Box IC483A - page 10

    CHAPTER 4: Ground Strap and Pin Connections 9 4. Ground Strap and Pin Connections 4.1 Ground Strap Signal grounds (Pins 19, 20, and 37 on the 422 inter face and Pin B on the V .35 inter face) are connected together , but not connected to chassis ground (Pin A). However , for applications requiring the grounds at a common reference point, the ground ...

  • Black Box IC483A - page 11

    V .35 ↔ RS422 INTERF ACE CONVER TER 10 4.2 Pin Connections Figures 4-1 and 4-2 show the pin connections for the V .35 ↔ RS-422 Inter face Converter . The illuminated LEDs in these figures indicate incoming signals only . The unit is shipped without the jumper (Rx) between signal ground and chassis ground. The RS-422 port is configured DTE and t ...

  • Black Box IC483A - page 12

    CHAPTER 4: Ground Strap and Pin Connections 11 Figure 4-1. The Converter Configured Figure 4-2. The Converter Configured for for RS-422 as DTE and V .35 as DCE. RS-422 as DCE and V .35 as DTE. 4 22 6 24 7 25 9 27 11 29 13 31 5 23 8 26 P S DS6 TD DS5 RD R T C D E DS1 RTS DS3 CTS F Y AA DS2 DSR DS4 SD DS8 TC DS7 RC V X 12 30 H C A B W2 DS9 DM/DTR 17 ...

  • Black Box IC483A - page 13

    1000 P ark Drive • Lawrence, P A 15055-1018 • 724-746-5500 • F ax 724-746-0746 © Copyright 1995. Black Box Corporation. All rights reserv ed. ...

Fabbricante Black Box Categoria Network Card

I documenti che otteniamo dal fabbricante del dispositivoBlack Box IC483A possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Black Box
- manuali per l’uso IC483A
- schede prodotto Black Box
- opuscoli
- o etichette energetiche Black Box IC483A
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Black Box IC483A.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Black Box IC483A, manuali di manutenzione, brevi manuali o manuali utente Black Box IC483A. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Black Box IC483A.

Manuali per l’uso simili

Manuale completo del dispositivo Black Box IC483A, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Black Box IC483A dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Black Box IC483A.

Il manuale per l’uso completo Black Box, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Black Box IC483A - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Black Box IC483A, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Black Box IC483A che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Black Box IC483A - che ci dovrebbe aiutare nei primi passi durante l'uso Black Box IC483A
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Black Box IC483A
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Black Box IC483A in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Black Box IC483A?

Utilizza il modulo sottostante

Se non hai risolto il problema con Black Box IC483A con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Black Box IC483A è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Commenti (0)