-
StarTech.com VS420RDVIA - page 1
VS420RDVIA DVI Video and Audio Matrix Splitter / Switcher - 2 in x 4 out ...
-
StarTech.com VS420RDVIA - page 2
FCC Compliance Statement This equipment has been tested and found to comply with the limits f or a Class B digital de - vice, pursuant to par t 15 of the FCC Rules. These limits are designed to provide reasonable protection against har mful interference in a residential installation. This equipment generates , uses and can r adiate radio frequency ...
-
StarTech.com VS420RDVIA - page 3
Instruction Manual i Instruction Manual T able of Contents Introduction ................................................................................... 1 Features ...................................................................................... 1 P ackage Contents ....................................................................... 2 In ...
-
StarTech.com VS420RDVIA - page 4
Instruction Manual 1 Introduction Thank you f or purchasing a StarT ech.com VS420RD VIA D VI Video and Audio Matrix Splitter/Switcher - 2 in x 4 out. With the Conv erge A/V D VI Matrix splitter/switcher , you can select between two D VI-I sources on multiple monitors (up to f our). With the push of a b utton, the VS420RD VIA lets you select what in ...
-
StarTech.com VS420RDVIA - page 5
Instruction Manual 2 Package Contents 1 X D VI Video and Audio Matrix Switcher • 1 X Instruction Manual • 1 X IR External Sensor • 1 X P ower Adapter • 1 X Remote Control • 1 X Set of Ear-Mounts for Rac k Mounting • Inst alla tion Input Connection Step 1 Connect the D VI video por t of the computer to the Source 1 por ...
-
StarTech.com VS420RDVIA - page 6
Instruction Manual 3 Step 2 Connect the speaker port of the computer to the Audio port of Source 1 as shown. Step 3 Repeat Step 1 and 2 on Source 2, as shown. Output Connection Step 1 Connect your monitor to port 1 of the Video Matrix Switch, as shown ...
-
StarTech.com VS420RDVIA - page 7
Instruction Manual 4 Step 2 Connect a pair of speakers to port 1 of the Video Matrix Switch, as shown. Step 3 Repeat Step 1 and 2 on the audio and video output channels for port 2, if necessary . Step 4 Apply power to the Video Matrix Switch as shown. ...
-
StarTech.com VS420RDVIA - page 8
Instruction Manual 5 Basic Operations Front Panel Opera tion Once the unit has been powered on, all 4 red LEDs should be illuminated. Due to the factory default settings , if all 4 red LEDs are blinking, source 1 is empty . When all 4 LEDs are always ON then a video signal has been detected at source 1. Setting Monitor Routes Route Source 1 or 2 to ...
-
StarTech.com VS420RDVIA - page 9
Instruction Manual 6 Step 3 Press 1 or 2 within 3 seconds to select Source 1 or Source 2. After select- ing, LED 4 will become either red or orange. Red means Source 1 is selected. • Orange means Source 2 is selected. • Step 4 Repeat Step 1 through 3 to route other por ts . Remote Control Operation Using the included external sensor , the ...
-
StarTech.com VS420RDVIA - page 10
Instruction Manual 7 Setting Monitor Routes Route Source 1 or 2 to Monitor s 1 through 4 respectively Step 1 Press the desired por t (ie . 4). Step 2 Press S1 or S2 to route Source 1 or Source 2 to Monitor 4. Step 3 Repeat Step 1 and 2 to route other por ts . Optional: If you would lik e to turn the video or audio por ts ON or OFF , you ma y do so ...
-
StarTech.com VS420RDVIA - page 11
Instruction Manual 8 Advanced Operations Front Panel Opera tion T urn the Video ON/OFF Step 1 Press the desired por t (ie . 2). Step 2 Press and hold “Option” and the LED light 1 will light up. If the LED light is green it means the video output de vice is powered on. If it is red, then the monitor is powerd off . Step 3 Press 1 to turn off Mon ...
-
StarTech.com VS420RDVIA - page 12
Instruction Manual 9 T urn the Audio ON/OFF Step 1 Press the desired por t (ie . 1). Step 2 Press and hold “Option” and the LED light 2 will light up. If the LED light is green, it means the audio output is pow ered on. If it is red, then the audio output is powered off . Step 3 Press 2 to turn off the audio of Monitor 1. Step 4 If necessary re ...
-
StarTech.com VS420RDVIA - page 13
Instruction Manual 10 T urn ON/OFF the Auto Scan In the auto scan mode, the Video Matrix Switch automatically swithces between Source 1 and Source 2 sequentially f or a par ticular monitor . Step 1 Press the desired por t (ie . 4). Step 2 Press and hold Option. Step 3 Press 3 to turn on the auto scan mode for Monitor 4. Step 4 If necessary , repeat ...
-
StarTech.com VS420RDVIA - page 14
Instruction Manual 11 Set the A uto Scan Time Inter v al Step 1 Press 3 and 4 at the same time. Step 2 All four LEDs should be b linking. Press one to set the auto scan time interval. 1 represents 8 seconds • 2 represents 15 seconds • 3 represents 30 seconds • 4 represents 45 seconds • Reset the Unit to its Default Settings P ow ...
-
StarTech.com VS420RDVIA - page 15
Instruction Manual 12 Unit Stack This function allows the user to use one single remote control to com- mand up to 16 Video Matr ix Switch units. Setting the Remote Controlling ID on the system P ower off the Video Matrix Switch 1. Press and hold 1 and 2 at the same time. 2. P ower on the Video Matrix Switch. 3. Release 1 and 2. 4. Select any one o ...
-
StarTech.com VS420RDVIA - page 16
Instruction Manual 13 Optimize the Video Signal Strength The optimal video signal strength can be adjusted to correspond to the length and quality of the D VI cables being used. Each monitor has two different video strength settings . For e xample, were the user to change the video strength setting of Source 2 for Monitor 3, the necessary steps wou ...
-
StarTech.com VS420RDVIA - page 17
Instruction Manual 14 Rackmount Kit (Optional) The follo wing figure shows how to properly attach the optional mounting brack ets to the Video Matrix Switch unit, f or use with an industrial stan- dard, 19-inch rack cabinet. ...
-
StarTech.com VS420RDVIA - page 18
Instruction Manual 15 Specications Specifications VS420RD VIA Number of Video Source P or ts 2 Number of Monitor P or ts 4 Video T ype D VI Remote Control Y es Remote Control Extender Jac k Y es Push-Button Control 5 LEDs 5 Hot-Plug & Play Y es Rack-Mounted 19” industr y standard Automatic Scan interval 8, 15, 30, 45 seconds D VI Cable Le ...
-
StarTech.com VS420RDVIA - page 19
Instruction Manual 16 T echnical Support StarT ech.com’ s lifetime technical support is an integral par t of our commit- ment to pro vide industr y-leading solutions. If you ev er need help with your product, visit www .star tech.com/suppor t and access our comprehensiv e selection of online tools, documentation, and downloads . Warranty Informat ...
-
StarTech.com VS420RDVIA - page 20
StarT ech.com has been making “hard-to-find easy” since 1985, providing high quality solutions to a diverse IT and A/V customer base that spans man y channels, including go vernment, education and industrial f acilities to name just a f ew . We offer an unmatched selection of computer par ts , cables , A/V products , KVM and Serv- er Managemen ...
Hai una domanda su StarTech.com VS420RDVIA?
Utilizza il modulo sottostante
Se non hai risolto il problema con StarTech.com VS420RDVIA con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con StarTech.com VS420RDVIA è probabile che voglia condividere il modo di risolverlo.