Italiano dropdown-ico

Manuale per l’uso Delta 36-451X

32 pagine 2.2 mb
Scarica

Vai alla pagina of 32

Summary
  • Delta 36-451X - page 1

    INSTRUCTION MANUAL T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). 10" Contractor’ s Saw (Models 36-441B, 36-451X) P ART NO. 422-19-651-0058 - 03-22-04 Copyright © 2004 Delta Machinery NOTE: ...

  • Delta 36-451X - page 2

    2 W oodworking can be danger ous if safe and proper operating procedur es are not followed. As with all machinery , there are certain hazar ds involved with the operation of the product. Using the machine with r espect and caution will considerably lessen the possibility of personal injury . However , if normal safety precautions ar e overlooked or ...

  • Delta 36-451X - page 3

    3 GENERAL SAFETY RULES 1. FOR YOUR OWN SAFETY , READ THE INSTRUCTION MANUAL BEFORE OPERA TING THE MACHINE. Learning the machine’ s application, limitations, and specific hazards will gr eatly minimize the possibility of accidents and injury . 2. WEAR EYE PROTECTION. AL WA YS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is d ...

  • Delta 36-451X - page 4

    4 F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJURY . ADDITIONAL SAFETY RULES FOR CONTRACTOR SA W 1 . DO NOT OPERA TE THIS MACHINE until it is assembled and installed according to the instructions. 2. OBT AIN ADVICE FROM YOUR SUPERVISOR, instructor , or another qualified person if you are not familiar with the operation of this ...

  • Delta 36-451X - page 5

    5 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cor ds which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug. Before connec ...

  • Delta 36-451X - page 6

    6 Use proper extension cor ds. Make sure your extension cord is in good condition and is a 3-wir e extension cord which has a 3-pr ong grounding type plug and matching receptacle which will accept the machine’ s plug. When using an extension cord, be sure to use one heavy enough to carry the current of the machine. An undersized cord will cause a ...

  • Delta 36-451X - page 7

    7 FOREWORD Delta Model 36-441B 10" Contractor’ s Saws are designed to give high quality performance with maximum depth of cut capacity up to 3-1/8" at 90° and 2-1/8" at 45°. These Delta Models come equipped with basic machine, sturdy steel stand, integral dust chute, patented Auto-Set T -Slot miter gage, heavy duty motor , lar ge ...

  • Delta 36-451X - page 8

    8 UNP ACKING AND CLEANING Continued Fig. 2 1 6 2 * 3 * 5 7 * 8 * 9 11 10 14 13 12 15 18 17 16 21 * 20 * 19 * 4 1. Contractor’ s Saw 2 * . Blade Tilting Handwheel (Zinc plated on 36-451X) 3 * . Handwheel Lock Knob (Zinc plated on 36-451X) 4. Blade Guard and Splitter Assembly 5. T able Insert 6. Miter Gage 7 * . Miter Gage Handle (Zinc plated on 36 ...

  • Delta 36-451X - page 9

    9 UNP ACKING AND CLEANING Continued 1. Combination Dust Chute/Support Panel 2. Motor Pulley 3. Motor 4. Pulley Guard 5. Drive Belt 6. Spring 7. Pins (2) for Mounting Motor 8. Motor Mounting Plate 9. 5/16 Star Washers (4) 10. 5/16 Flat W ashers (4) 11. 5/16-18 x 3/4 " Carriage Head Scr ews (4) Fig. 3 21 22 20 18 19 17 16 15 14 12 10 13 11 9 7 8 ...

  • Delta 36-451X - page 10

    10 DO NOT OPERA TE THIS MACHINE UNTIL YOU READ AND UNDERST AND THE ENTIRE INSTRUCTION MANUAL. MAKE SURE THE SAW IS SECUREL Y A TT ACHED TO THE ST AND BEFORE PERFORMING ANY CUTTING OPERA TIONS. Fig. 4 Fig. 5 Fig. 6 ASSEMBLING SAW ST AND 1. Assemble the dust chute and support panel (A) Fig. 4, to the inside of the front stand panel (B) with thr ee #1 ...

  • Delta 36-451X - page 11

    11 The motor shipped with your saw is a 1-1/2 H.P . at 115 volts or 2 H.P . at 230 volts, Ball Bearing, Capacitor Start/Capacitor Run motor . This motor has been especially selected to best supply power to your machine, and the relative safety of the machine is enhanced by its use. Use only this motor , as the use of other motors may be detrimental ...

  • Delta 36-451X - page 12

    12 Fig. 14 Fig. 13 ASSEMBLING MOTOR AND MOTOR MOUNTING PLA TE TO SA W DISCONNECT MACHINE FROM POWER SOURCE. 1. Locate the two pins (X) Fig. 12 that insert into holes (D) in each side of bracket (B). The pins (X) are spring (Y) loaded from factory . 2. Position motor and motor mounting plate (A) Fig. 13 below bracket (B) to allow bracket arm to slid ...

  • Delta 36-451X - page 13

    13 Fig. 15 Fig. 16 Fig. 17 Fig. 18 ASSEMBLING MOTOR PULLEY , BEL T PULLEY GUARD, AND DRIVE BEL T DISCONNECT MACHINE FROM THE POWER SOURCE. 1. Remove the motor shaft key that is taped to the motor . 2. Insert the key (A) Fig. 15 in the keyway on the motor shaft. Assemble the motor pulley (B) on the motor shaft with the hub of the pulley facing out. ...

  • Delta 36-451X - page 14

    14 Fig. 19 Fig. 20 Fig. 21 Fig. 22 7. Lift the motor and assemble the drive belt (H) Fig. 19 to the arbor pulley and motor pulley (B). The weight of the motor will provide the corr ect belt tension. 8. IMMEDIA TEL Y AFTER ASSEMBLING THE BEL T , RAISE THE SAW BLADE TO ITS MAXIMUM HEIGHT AND TIL T THE SAW BLADE TO 45°. CHECK TO SEE IF THE MOTOR (J) ...

  • Delta 36-451X - page 15

    15 Fig. 24 Fig. 25 Fig. 26 ASSEMBLING BLADE GUARD AND SPLITTER ASSEMBL Y DISCONNECT MACHINE FROM POWER SOURCE . 1. Fasten the r ear splitter mounting bracket (A) Fig. 24, to the rear trunnion using the two 1/4-20 x 3/4" hex head bolts (B) and flat washers. Do not completely tighten the two bolts (B) at this time. 2. Raise saw arbor to its high ...

  • Delta 36-451X - page 16

    16 Fig. 27 Fig. 28 Fig. 29 Fig. 30 5. If alignment is necessary , loosen the two screws (F) Fig. 27, align bracket (D) with the arbor flange (E), and tighten scr ews (F). 6. Loosely assemble large washer and bolt (C) Fig. 27, t o the inside splitter bracket. This bolt and washer was removed in STEP 3 . 7. Assemble the blade guar d and splitter asse ...

  • Delta 36-451X - page 17

    17 Fig. 31 Fig. 32 Fig. 33 Fig. 34 9. With the blade guar d (L) Fig. 31, in the raised position, assemble the saw blade (K) on the saw arbor and tighten secur ely with two arbor wr enches supplied. See section “CHANGING SAW BLADE.” 10. Use a straight edge (E) to check to see if the saw blade is aligned with the rear of the splitter (G) in Figs. ...

  • Delta 36-451X - page 18

    18 ASSEMBLING STEEL EXTENSION WING AND SWITCH ( MODEL 36-441B) DISCONNECT MACHINE FROM POWER SOURCE. 1. Assemble extension wing (A) Fig. 39, to the saw table using three 7/16-20 x 3/4" bolts (B) and flat washers (C). 2. With a straight edge (D) Fig. 39, make certain the extension wing (A) is level with the saw table befor e tightening thr ee b ...

  • Delta 36-451X - page 19

    19 Fig. 45 A ST AR TING AND STOPPING SAW 1. The on/off switch is located underneath the switch shield (A) Fig. 42. T o turn the saw “ON”, move switch trigger (B) to the up position. 2. T o turn the saw “OFF”, push down on switch shield (A) Fig. 43. Fig. 42 Fig. 43 A B A Fig. 44 LOCKING SWITCH IN THE “OFF” POSITION IMPORT ANT : When the ...

  • Delta 36-451X - page 20

    20 Fig. 46 Fig. 47 C B F A Fig. 48 E D A B C D E RAISING AND LOWERING THE BLADE T o raise the saw blade, loosen lock knob (A) Fig. 46, and turn the blade raising handwheel (B) clockwise. When the blade is at the desired height, tighten lock knob (A). T o lower the blade, loosen lock knob (A) Fig. 46, and turn the handwheel (B) counterclockwise. NOT ...

  • Delta 36-451X - page 21

    21 21 CHECKING BLADE ALIGNMENT BLADE ALIGNMENT IS F ACTOR Y SET AND SHOULD NOT NEED ADJUSTMENT . ADJUSTING BLADE ALIGNMENT IN THE FIELD IS A DIFFICUL T AND TIME-CONSUMING PROCEDURE. ALL SAW BLADES HA VE SOME RUN-OUT . THEREFORE, RE-ADJUSTING BLADE ALIGNMENT SHOULD ONL Y BE A TTEMPTED IF IT BECOMES NECESSAR Y . DISCONNECT MACHINE FROM POWER SOURCE. ...

  • Delta 36-451X - page 22

    22 Fig. 53 Fig. 54 C A B B A DISCONNECT MACHINE FROM POWER SOURCE. 1. NOTE: T wo 7/8" wrenches are supplied with the saw fo r changing the saw blade: a box end wr ench (A) Fig. 53 & 54, and open end wrench (B) Fig. 53 & 54. Use only 10" saw blades rated for 3000 RPM or higher with 5/8" arbor holes. 2. Remove table insert (C) ...

  • Delta 36-451X - page 23

    23 23 Fig. 55 B A C B DISCONNECT MACHINE FROM POWER SOURCE. Place a straight edge across the table at both ends of the table insert. The table insert (A) Fig. 55 should always be level with the table. If an adjustment is necessary , tur n the adjusting screws (B). Four adjusting scr ews (B) are supplied in the table insert. The table insert is equi ...

  • Delta 36-451X - page 24

    24 COMMON SA WING OPERA TIONS CROSS-CUTTING Cross-cutting r equires the use of the miter gage to position and guide the work. Place the work against the miter gage and advance both the gage and work toward the saw blade, as shown in Fig. 59. The miter gage may be used in either table slot. When bevel cutting (blade tilted), use the table groove tha ...

  • Delta 36-451X - page 25

    25 Ripping is cutting lengthwise through a boar d. The rip fence (A) Fig. 62 [not supplied] is used to position and guide the work. One edge of the work rides against the rip fence while the flat side of the board r ests on the table. Since the work is pushed along the fence, it must have a straight edge and make solid contact with the table. The s ...

  • Delta 36-451X - page 26

    26 Fig. 66 Fig. 69 Fig. 67 Fig. 68 H G W H USING MOULDING CUTTERHEAD Moulding is cutting a shape on the edge or face of the work. Cutting mouldings with a moulding cutterhead is a fast, safe and clean operation.The many differ ent knife shapes available make it possible for the operator to produce almost any kind of mouldings, such as various style ...

  • Delta 36-451X - page 27

    27 Fig. 74 Fig. 75 Fig. 72 Fig. 73 Fig. 71 1. Dadoing is cutting a rabbet or wide groove into the work. Most dado head sets are made up of two outside saws and four or five inside cutters, (Fig. 71). V arious combinations of saws and cutters are used to cut grooves fr om 1/8" to 13/16" for use in shelving, making joints, tenoning, groovin ...

  • Delta 36-451X - page 28

    28 Fig. 76, illustrates dimensions for making a typical featherboard. The material which the featherboar d is constructed of, should be a straight piece of wood that is free of knots and cracks. Featherboar ds are used to keep the work in contact with the fence and table, as shown in Fig. 77, and help prevent kickbacks. Clamp the featherboards to t ...

  • Delta 36-451X - page 29

    When ripping work less than 4 inches wide, a push stick should be used to complete the feed and could easily be made from scrap material by following the pattern shown in Fig. 78. Fig. 78 PUSH STICK MAKE FROM 1/2 " OR 3/4 " WOOD OR THICKNESS LESS THAN WIDTH OF MA T’L. TO BE CUT CUT OFF HERE TO PUSH 1/4 " WOOD CUT OFF HERE TO PUSH 1 ...

  • Delta 36-451X - page 30

    30 MAINTENANCE KEEP MACHINE CLEAN Periodically blow out all air passages with dry compressed air . All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. W ear ANSI Z87.1 safety glasses while using compressed air . F AILURE TO ST AR T Shou ...

  • Delta 36-451X - page 31

    31 P AR TS, SER VICE OR W ARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standards and ar e serviced by a network of Porter -Cable • Delta Factory Service Centers and Delta Authorized Service Stations. T o obtain additional information regar ding your Delta quality product or to obtain parts, service, war ...

  • Delta 36-451X - page 32

    The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas registradas de POR TER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T ...

Fabbricante Delta Categoria Router

I documenti che otteniamo dal fabbricante del dispositivoDelta 36-451X possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Delta
- manuali per l’uso 36-451X
- schede prodotto Delta
- opuscoli
- o etichette energetiche Delta 36-451X
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Delta 36-451X.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Delta 36-451X, manuali di manutenzione, brevi manuali o manuali utente Delta 36-451X. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Delta 36-451X.

Manuali per l’uso simili

Manuale completo del dispositivo Delta 36-451X, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Delta 36-451X dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Delta 36-451X.

Il manuale per l’uso completo Delta, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Delta 36-451X - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Delta 36-451X, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Delta 36-451X che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Delta 36-451X - che ci dovrebbe aiutare nei primi passi durante l'uso Delta 36-451X
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Delta 36-451X
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Delta 36-451X in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Delta 36-451X?

Utilizza il modulo sottostante

Se non hai risolto il problema con Delta 36-451X con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Delta 36-451X è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)