Italiano dropdown-ico

Manuale per l’uso Pelco ED2920

36 pagine 0.71 mb
Scarica

Vai alla pagina of 36

Summary
  • Pelco ED2920 - page 1

    PELCO Manual C460M-E (7/95) 33 ED28/ED2820 and ED29/ED2920 “Harris Dome” Enclosur es Installation/Operation Manual C460M-E (7/95) ® PELCO • 3500 Pelco Way • Clovis, CA 93612-5699 • USA • www.pelco.com (800) 289-9100 or (1-559) 292-1981 • FAX (800) 289-9150 or (1-559) 292-3827 ...

  • Pelco ED2920 - page 2

    ii PELCO Manual C460M-E (7/95) TABLE OF CONTENTS S ection P age 1.0 W ARNINGS .................................................................................................................... .................... 1 2.0 SCOPE .......................................................................................................................... ...

  • Pelco ED2920 - page 3

    PELCO Manual C460M-E (7/95) iii 14.0 ENCLOSURE SPECIFICA TIONS ................................................................................................... .2 8 15.0 P AN/TIL T ASSEMBLIES ........................................................................................................ ........... 29 15.1 ASSEMBL Y DESCRIPTION ........ ...

  • Pelco ED2920 - page 4

    iv PELCO Manual C460M-E (7/95) REVISION HISTORY Manual # Date Comments C460M 3/89 Original Version. C460M 6/90 Revision A. Manual separated into two parts: enclosures and pan/tilt. Completely revised to include ED2820RX/PP and ED2820SL-RX/PP models. C460M 11/90 Revision B. Figure 2-4 revised. C460M 6/92 Revision C. Completely revised to include the ...

  • Pelco ED2920 - page 5

    PELCO Manual C460M-E (7/95) 1 Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit. CAUTION: RISK OF ELECTRIC SHOCK. DO NOT OPEN. 1.0 WARNINGS Prior to installation ...

  • Pelco ED2920 - page 6

    2 PELCO Manual C460M-E (7/95) 2.0 SCOPE The information contained within this manual covers the Harris Environmental Dome. 3.0 DESCRIPTION This product was developed outside of PELCO’s nor- mal product development process, and outside of nor- mal working hours by Jimmy Harris, Sheet Metal De- partment Manager. In recognition of this extraordinary ...

  • Pelco ED2920 - page 7

    PELCO Manual C460M-E (7/95) 3 4.0 INSTALLATION 4.1 UNPACKING INSTRUCTIONS The dome and enclosure are shipped in separate cartons. Make sure you have both before installing. Save the shipping cartons and plastic packaging in case any part of the unit has to be returned for credit or repair. 4.2 CONDUCTOR REQUIREMENTS ED28 ED29 See the camera manufac ...

  • Pelco ED2920 - page 8

    4 PELCO Manual C460M-E (7/95) Figure 3 . Heater/Blower Wiring Diagram (120 VAC) 4.3 WIRING INSTRUCTIONS Models ED28-1 and ED29-1 These models are supplied with a factory installed heater/blower and service light. Supply 120 VAC power for the heater/blower and wire according to Figures 3. Models ED2820-3, ED2820-3SL/PP, ED2920-3, ED29-3 These models ...

  • Pelco ED2920 - page 9

    PELCO Manual C460M-E (7/95) 5 Number Function 1 Iris 2 Zoom 3 Focus 4 Lens Common 5 Manual Iris 6 Not Used 7 Camera On 8 AC Input High 9 AC Input Neutral 10 Ground Number Function 11 Not Used 12 Not Used 13 Heater #2 14 Not Used 15 Connect Heaters 1 & 2 16 Not Used 17 Heater #1 18 AC High 19 AC Neutral 20 Ground Number Function 21 Fan 22 Not Us ...

  • Pelco ED2920 - page 10

    6 PELCO Manual C460M-E (7/95) 28 POS CONNECTOR POS. COLOR DESC. 1 BROWN P/T COMMON 2 WHT/VIO VIDEO CORE 3 RED LEFT 4 WHT/BLK VIDEO SHIELD 5 YELLOW DOWN 6 ORANGE UP 7 BLUE RIGHT 8 GREEN GROUND 9 WHITE CAMERA AC HIGH 10 BLACK IRIS 1 1 WHT/BRN FOCUS 12 WHT/RED ZOOM 13 WHT/ORG LENS COMMEN 14 WHT/YEL CAMERA AC LOW 17 WHT/BLU PRESET COMMEN 18 GRY/WHT PRE ...

  • Pelco ED2920 - page 11

    PELCO Manual C460M-E (7/95) 7 Figure 7 . Coaxitron/Wiretron Power Patch (CX9024RX/WX8024RX) Wiring Schematic 4.4 INSTALLATION INSTRUCTIONS The Harris Dome is supplied in three (3) configurations: as a passive dome (for use as a dummy dome or with a fixed camera ), with a factory installed pan/tilt, or with a factory installed pan/tilt and receiver/ ...

  • Pelco ED2920 - page 12

    8 PELCO Manual C460M-E (7/95) Figure 9 . Wall Mounting 4.4.1 M ounting the ED28/ED2820 Series 4.4.1.1 Wall Mounting The ED28/ED2820 series may be mounted directly to a wall or vertical surface. To attach the enclosure to a vertical surface, perform the following (see Figure 9): 1. Using the enclosure or the template supplied (see Figure 12), mark t ...

  • Pelco ED2920 - page 13

    PELCO Manual C460M-E (7/95) 9 4.4.1.2 Corner Mounting The ED28/ED2820 series may be mounted to the out- side corner of a structure using the CM100 Corner Mount Adapter. To attach the enclosure to an outside corner, perform the following steps (see Figure 10): 1. Secure the CM100 corner mount adapter as stated in the installation manual provided wit ...

  • Pelco ED2920 - page 14

    10 PELCO Manual C460M-E (7/95) Figure 11 . Mounting Templates ED28/ED2820 SERIES AND EDM210 HOLE PATTERN ST1 HOLE PATTERN ...

  • Pelco ED2920 - page 15

    PELCO Manual C460M-E (7/95) 11 Figure 12 . EDM210 Mounting Extension Installation 4.4.1.3 EDM210 Mounting Extension When needed, the ED28/ED2820 series dome may be mounted 10 inches (25.4 cm) farther from the mounting surface with the use of the EDM210 mounting exten- sion. It should be noted that in areas with heavy snowfall or high winds, the ST1 ...

  • Pelco ED2920 - page 16

    12 PELCO Manual C460M-E (7/95) 4.4.1.4 Parapet or Pole Mounting When mounting to a parapet, use of the PP200/PPI200 parapet mount or PP300/PP301 parapet corner mounts is recommended. The ED28/ED2820 series dome may be mounted to other standard PELCO mounts, includ- ing the PP100 Parapet Mount or the PA102 Pole Mount. These mounts can be used in con ...

  • Pelco ED2920 - page 17

    PELCO Manual C460M-E (7/95) 13 4.4.2 Mounting the ED29/ED2920 Series The ED29/ED2920 Series domes require a suitable length of 1-1/2-inch NPT threaded pipe (not supplied) for mounting. The dome can be attached to any wall or ceiling capable of supporting the full weight of the mount, pan/tilt, camera/lens, and enclosure. We suggest using the MRWA w ...

  • Pelco ED2920 - page 18

    14 PELCO Manual C460M-E (7/95) 6.0 ED28 EXPLODED ASSEMBLY DIAGRAM Figure 14 . ED28 Exploded Assembly Diagram ...

  • Pelco ED2920 - page 19

    PELCO Manual C460M-E (7/95) 15 7.0 ED28 MECHANICAL PARTS LIST The following parts list corresponds to the exploded assembly diagram in Figure 14. Item Qty Description Part Number 1 2 Fastener ED210000 2 2 Receptacle ED210001 3 2 Retainer ED210002 4 1 Holder, Lamp (not shown) ED210020 5 1 Back Box Assy ED28001001WA 6 1 Plate, Front ED28004003COMP 7 ...

  • Pelco ED2920 - page 20

    16 PELCO Manual C460M-E (7/95) 8.0 INSTALLATION In order to ensure proper wiring and system operation of all components, it is highly recommended that the pan/ tilt and the associated control equipment be tested in your facility before field installation is attempted. As- semble the mating connector as outlined in Figure 15 and wire the control cab ...

  • Pelco ED2920 - page 21

    PELCO Manual C460M-E (7/95) 17 Figure 15 . Connector Assembly 8.3 CONNECTOR ASSEMBL Y Installation and/or testing will require you to assemble the connector parts provided. Fabricate the intercon- necting cable according to the following steps (refer- ence Figure 15). 1. Slide part A of the cable clamp (item 1) over the end of the cable (item 1, pa ...

  • Pelco ED2920 - page 22

    18 PELCO Manual C460M-E (7/95) Note: For non-receiver models only , you must reverse the left/right and up/down function pins shown above if you are not using the C1906 or C1925 pretested cables. Figure 16 . PT2801000ASSY/PT2801001ASSY Wiring Diagram (Standard or SL Models) QTY SYMBOL DESCRIPTION MANUF ACTURER P ART NUMBER 2 C1,C2 CAP ACITOR,15 MFD ...

  • Pelco ED2920 - page 23

    PELCO Manual C460M-E (7/95) 19 Note: For non-receiver models only , you must reverse the left/right and up/down function pins shown above if you are not using the C1906/PP or C1925/PP pretested cables. Figure 17 . PT2801002ASSY Wiring Diagram (Standard with Presets) ...

  • Pelco ED2920 - page 24

    20 PELCO Manual C460M-E (7/95) Note: For non-receiver models only , you must reverse the left/right and up/down function pins shown above if you are not using the C1906/PP or C1925/PP pretested cables. Figure 18 . PT2801003ASSY Wiring Diagram (SL with Presets) ...

  • Pelco ED2920 - page 25

    PELCO Manual C460M-E (7/95) 21 8.4 LIMIT/STOP ADJUSTMENTS WARNING: Do not operate pan/tilt without limit stops. Do not remove or reposition the fixed actuator on the non-SL. DAMAGE WILL OCCUR. NOTE: SL models are not equipped with pan limit stops. (Disregard steps 1-5 below). To set limit stops, perform the following steps (refer to Figure 19). 1. ...

  • Pelco ED2920 - page 26

    22 PELCO Manual C460M-E (7/95) 9.2 AUTO/RANDOM SCAN OPERATION The pan/tilt will function in the Auto/Random mode with the addition of the appropriate PELCO control system. The pan/tilt has no additional limit switches or relays for auto scan operation and is, therefore, only compatible with current sensing auto/random type cir- cuits employed in ou ...

  • Pelco ED2920 - page 27

    PELCO Manual C460M-E (7/95) 23 Figure 20 . Exploded Assembly Parts Diagram (Model PT2801000ASSY) 11.0 EXPLODED ASSEMBLY DIAGRAM (Model PT2801000ASSY) ...

  • Pelco ED2920 - page 28

    24 PELCO Manual C460M-E (7/95) Figure 21 . Exploded Assembly Hardware Diagram (Model PT2801000ASSY) 11.1 EXPLODED HARDWARE DIAGRAM (Model PT2801000ASSY) ...

  • Pelco ED2920 - page 29

    PELCO Manual C460M-E (7/95) 25 12.0 MECHANICAL PARTS LIST (PT2801000ASSY) The following parts list corresponds to the exploded assembly diagram in Figure 20. Item Qty Description Part Number 1 4 Ring, Snap #Q2-18 15510000 2 Ring, Snap #Q2-18 (SL) 15510000 2 1 Pin, Pan Limit (Non-SL) 1554049COMP 1 Pin, Pan Limit (P/PP Only) 2804003COMP 3 1 Pin, T il ...

  • Pelco ED2920 - page 30

    26 PELCO Manual C460M-E (7/95) 45 1 Gear , SP Delrin (SL/PP) 280010016 1 Gear , 1.875 Plastic (P/PP) PT250010002 46 1 Gear , SP Delrin 28010017 47 1 Bracket, Pot Pan (P/PP) 2804014COMP 1 Bracket, Pot Pan (SL/PP) 2804117COMP 48 1 Bracket, Pot Pan 2804015COMP 49 1 Gear , Preset Pan Spindle 2804016COMP 50 1 Gear , Preset T ilt Shaft 2804020COMP 51 1 C ...

  • Pelco ED2920 - page 31

    PELCO Manual C460M-E (7/95) 27 13.0 ENCLOSURE MODELS ED28 Harris environmental discreet sur- veillance enclosure with black opaque lower dome with clear viewing win- dow for outdoor applications. Fixed camera mount supplied. (UL, CE) ED28-1 Same as ED28 except supplied with factory installed heater/blower and service light. (UL) ED2820 Harris envir ...

  • Pelco ED2920 - page 32

    28 PELCO Manual C460M-E (7/95) Fuse Protection: 3 AG type Control Method: 15-pulse train (pulse width modu- lated) superimposed on the video sig- nal during the vertical interval by the control transmitter. Pulse train occu- pies one TV line period. Input Video Line: 1 v p-p nominal; 2v p-p maximum at less than 75% APL; 1.5v p-p maxi- mum at 90% AP ...

  • Pelco ED2920 - page 33

    PELCO Manual C460M-E (7/95) 29 ELECTRICAL Input Voltage: 24 VAC required for pan/tilt Power Requirements: Running Pan — .31 amp (7.5 vA) Tilt — .38 amp (9.2 vA) Starting Pan — .47 amp (11.2 vA) Tilt — .56 amp (13.5 vA) Maximum Current: 2 amps per conductor (SL models only) Connectors: Pan/Tilt Amp CPC type (mate sup- plied). Installed onto ...

  • Pelco ED2920 - page 34

    30 PELCO Manual C460M-E (7/95) 17.0 PAN/TIL T ASSEMBL Y INST ALLA TION This section covers the installation of the ED28KIT in retrofitting a non-pan/tilt-equipped ED28 and ED28-1 or ED29/ED29-1/ED29-3 Harris Dome with a pan/tilt assembly unit. Please read through and understand the installation instructions before proceeding with the in- stallation ...

  • Pelco ED2920 - page 35

    PELCO Manual C460M-E (7/95) 31 Exploded Assembly Parts List Item Qty Description Part Number 1 1 Bracket PM200C4000COMP 2 1 Dome drive bracket SB34105COMP A 3 Bolt, 1/4-20 x 5/8" hex C/S ZH1/4-20X.625CH B 2 Nut lock, 1/4-20, nylon insert SS ZH1/420NUTCHN C 3 W asher , split lock, 1/4" SS ZH1/4L WSSL D 5 Washer , flat, nylon ZH260X562X65C ...

  • Pelco ED2920 - page 36

    32 PELCO Manual C460M-E (7/95) 18.0 WARRANTY AND RETURN INFORMATION This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycl ing t ...

Fabbricante Pelco Categoria Security Camera

I documenti che otteniamo dal fabbricante del dispositivoPelco ED2920 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Pelco
- manuali per l’uso ED2920
- schede prodotto Pelco
- opuscoli
- o etichette energetiche Pelco ED2920
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Pelco ED2920.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Pelco ED2920, manuali di manutenzione, brevi manuali o manuali utente Pelco ED2920. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Pelco ED2920.

Manuali per l’uso simili

Manuale completo del dispositivo Pelco ED2920, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Pelco ED2920 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Pelco ED2920.

Il manuale per l’uso completo Pelco, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Pelco ED2920 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Pelco ED2920, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Pelco ED2920 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Pelco ED2920 - che ci dovrebbe aiutare nei primi passi durante l'uso Pelco ED2920
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Pelco ED2920
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Pelco ED2920 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Pelco ED2920?

Utilizza il modulo sottostante

Se non hai risolto il problema con Pelco ED2920 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Pelco ED2920 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)