Italiano dropdown-ico

Manuale per l’uso Snapper ZMT2500KH, ZM5201M, ZM6101M

32 pagine 0.87 mb
Scarica

Vai alla pagina of 32

Summary
  • Snapper ZMT2500KH, ZM5201M, ZM6101M - page 1

    Safety Instructions & Operator’s Manual for MID M OUNT Z-RIDER ZERO TURNING HYDRO DRIVE SERIES 0 POWER UNIT MODELS ZMT2500KH MOWER UNIT MODELS ZM5200M ZM6100M MODEL NUMBER EXPLA NA TION Z M T 25 00 KH DRIVE DESIGNA TION ENGINE T YPE M OWER OPERATION SERIES DESIGNATION CONTROL DESIGNA TION ENGINE HP POWER UNIT Z – Zero Turning – Hy dro Dri ...

  • Snapper ZMT2500KH, ZM5201M, ZM6101M - page 2

    2 IM PORTA NT SA FETY INSTRUCTIONS WARNING: This powerf ul cuttin g machine is capable o f amputating h ands and feet and can throw objects that can cau se injury a nd damage! Failur e to comply with the following SA FETY instructions could result in ser ious injury or dea th to the operator or other persons. The ow ner of the machine must understa ...

  • Snapper ZMT2500KH, ZM5201M, ZM6101M - page 3

    3 IM PORTA NT SA FETY INSTRUCTIONS PREPA RA TION (Continued From Pre v ious Pa ge) 4. Handle fuel wit h extra care. Fuels are flammable and vap ors are explosive. Use only an approv ed fuel co ntainer. DO NOT remov e fuel cap or add fuel with engine running. A dd fuel outdoor s only with engine stopped and cool. Clean spilled fuel from machine. DO ...

  • Snapper ZMT2500KH, ZM5201M, ZM6101M - page 4

    4 TABLE OF CONTENTS IMPORTA NT SA FETY INSTRUCTIONS ................................................ 2-3 TA BLE OF CO NTENTS............................................................................. 4 SECTION 1 - FA MILIA RIZA TION .............................................................. 5 SECTION 2 - OPERA TIN G INSTRUCTIONS ............. ...

  • Snapper ZMT2500KH, ZM5201M, ZM6101M - page 5

    5 DECK LIFT LEVER WITH RELEASE BUTTON OPERA T OR’S SEA T FUEL TANK BLA DE ENGA GEM EN T SW I TCH KEY SW ITCH PA RKING BRAKE LEVER DISCHARGE DEFLECTOR ENGINE SPEED CONTR OL (INSIDE LEVER ) CHOKE CONTROL (OUT SIDE LEVER) MOTION CONTROL LEVERS AU X I L I AR Y F U E L TA NK Section 1 - FA MILIA R IZA TION FIGURE 1.1 1. 1 INT RODUCTION This manual has ...

  • Snapper ZMT2500KH, ZM5201M, ZM6101M - page 6

    6 Section 2 - OPERA TING INSTRUCTIONS 2.1 PRE-STA RT CHECK LIST Make the following c hecks and per form the service required bef ore each start-up. 2.1.1. Check tires and add or re lease air as needed to bring press ure to 12 psi in drive tires . Pressure in front dec k caster wheels should be 25 psi. 2.1.2. Check guards , deflectors and c overs to ...

  • Snapper ZMT2500KH, ZM5201M, ZM6101M - page 7

    7 Section 2 - OPERA TING INSTRUCTIONS 2.2 ST A RTIN G & STOPPIN G - ENGINE, BL A DES, PA RKING BRA KE This mac hine is equipped with dual hy drostatic wheel drive tr ansmiss ions. Eac h transm ission is controlled by a separate m otion control lever. The left lever c ontrols the lef t wheel drive transm ission and the right lever controls the r ...

  • Snapper ZMT2500KH, ZM5201M, ZM6101M - page 8

    8 Section 2 - OPERA T ING INSTRUCTIONS 2.2.5. PA RKING BRA KE 1. Engage parking brak e by pulling the parking brak e lever back to the engaged pos ition. NOTE : Motion control levers m ust be in the Neutral position to engage brak e. See Figure 2.6. NOTE: Engaging the parking brak e lock s the mo tion control levers in the neutral pos ition. 2. Rel ...

  • Snapper ZMT2500KH, ZM5201M, ZM6101M - page 9

    9 Section 2 - OPERA T ING INSTRUCTIONS 2.3 CUT TING HEIGHT A DJUS T MENT 1. Adjust cutting height as desired to any position, using deck lift lever. See Figur e 2.8. NOTE: T he engine does not have to be running to adjust cutting height. FIGURE 2.8 2.4 OPERA TION- M OTION CONT ROLS 2.4.1. DRIVING M A CHINE 1. Start engine. Releas e parking brak e. ...

  • Snapper ZMT2500KH, ZM5201M, ZM6101M - page 10

    10 Section 3 - MA INTENA NCE 3.1 INTRODUCT ION To retain the quality of the SNAPPER mower, us e genuine SNAPPER replacem ent parts only. Contact a local SNAPPER dealer for par ts and service as sistance. For the cor rect part or inf ormation for a particular SNAPPER mo wer, alway s mention the m odel and serial num ber. SNAPPER recom m ends returni ...

  • Snapper ZMT2500KH, ZM5201M, ZM6101M - page 11

    11 Section 3 - MA INTENA NCE 3.2.3. CHECK MOW ER DRIVE BE LT 1. Foot Rest Removal a. Lower deck to lowest setting. b. Rem ove foot res t. See Figure 3.3. c. Rem oval of foot re st will allow access to dec k belt. FIGURE 3.3 2. Checking Belt T ension The idler and s pring provide proper belt te ns io n and require no adjustm ent. If belt is frayed, ...

  • Snapper ZMT2500KH, ZM5201M, ZM6101M - page 12

    12 Section 3 - MA INTENA NCE 3.3.3. RIDING M OWER - LUBRICA T ION 1. Front Wheel Bearings Lubricate with Kendall NLGI No. 2 lithium greas e or equivalent, from a grease gun. See Figur e 3.5. FIGURE 3.5 2. Transaxle Check the level of fluid in both of the f luid reservoirs . W ipe away all dirt and debris from around res ervoir cap befor e removing. ...

  • Snapper ZMT2500KH, ZM5201M, ZM6101M - page 13

    13 Section 3 - MA INTENA NCE 3.5 A NNUA LLY (END OF EA CH SEA SON) (Continued from previous P age) 3.5.2. FUEL FILT ER Service f uel filter as instruct ed below. Turn ke y to “OFF ” position. Engine MUST be stopped and MUST be c old before rem oving filter. Clam p fuel line to prevent f uel spillage or perf orm f ilter change when fuel tank and ...

  • Snapper ZMT2500KH, ZM5201M, ZM6101M - page 14

    14 Section 3 - MA INTENA NCE 3.6 DECK REM OVA L (Continued from previous page) 5. Rem ove shoulder bolts, washers and nuts from rear lift arm . See Figure 3.11. FIGURE 3.11 6. Disconnect pull bar fr om f ront axle by rem oving clevis pins and cotter pins . See Figure 3.12. FIGURE 3.12 7. Pull lock collar back and slide power transf er shaf t away f ...

  • Snapper ZMT2500KH, ZM5201M, ZM6101M - page 15

    15 Section 4 - A DJUSTMENTS & REPA IR DA NGER Exercise EXT REME CAUTION w hen making this adjustment, due to clos e proximity of moving parts. 4.1 NEUTRA L POSITION A DJUS T MENTS The motion contr ol levers control the m ovem ent and stopping of the m achine. Move the motion c ontrol levers to the center or neutr al position to stop m achine. I ...

  • Snapper ZMT2500KH, ZM5201M, ZM6101M - page 16

    16 Section 4 - A DJUSTMENTS & REPA IR 4.2 .1. MOWER DEC K A DJU STMENT (L EVELNESS) (Continued) 6. Loosen the nuts and bolts that sec ure both fr ont and rear deck s upport brack ets on the high side of deck . Located above each support brack et, on the top part of the power unit fram e, are three shim plates. Remove the shim plates on both of ...

  • Snapper ZMT2500KH, ZM5201M, ZM6101M - page 17

    17 Section 4 - A DJUSTMENTS & REPA IR WA RNING DO NOT attempt any maintenance, adjustmen ts or service with engine running. S TOP engine. STOP blades. Set brake. Remov e key. Remove spark plug wires an d secu re aw ay from spark p lug s. Eng ine an d components are HOT . A v oid serious burns, allow sufficie nt time for all par ts to cool. 4.3 ...

  • Snapper ZMT2500KH, ZM5201M, ZM6101M - page 18

    18 Section 4 - A DJUSTMENTS & REPA IR 4.5.2. BLADE SHA RPENING 1. Rem ove blade. See Figure 4.5. FIGURE 4.5 2. Ins pect condition of blade. See F igure 4.4. 3. If blade is in good c ondition, sharpen at 22 to 28 degrees . DO NOT shar pen bey ond original cutting edge. See Figure 4.6. FIGURE 4.6 4. Check blade balance after sharpening. If neces ...

  • Snapper ZMT2500KH, ZM5201M, ZM6101M - page 19

    19 Section 4 - A DJUSTMENTS & REPA IR WA RNING Shield the positive t ermin al with terminal cover located on bat tery harness. T his prevent s metal f rom touching the positive terminal which could caus e sparks. Cables must b e connected to battery terminals in the proper position. RE D (Positive) ca b le must go to the ( + ) terminal. BLACK ( ...

  • Snapper ZMT2500KH, ZM5201M, ZM6101M - page 20

    20 Section 4 - A DJUSTMENTS & REPA IR Battery Condition Chart State of Charge Syr inge Hydrometer Digital Voltmeter Five Ball Hydrometer 100% Charged w/ Sulfate Stop 1.280 12.80v Five Balls Floating 100% Charged 1.265 12.60v Four Balls F loating 75% Charged 1.210 12.40v Three Balls Floating 50% Charged 1.160 12.10v Two Balls Floating 25% Charge ...

  • Snapper ZMT2500KH, ZM5201M, ZM6101M - page 21

    21 TROUBLESHOOTING PROBL EM PROBA BLE CA USE CORRECTIVE A CTION Starter Will Not Crank 1. Battery dead. 1. Service battery. Engine 2. Blown fuse. 2. Replace fuse. 3. Electrical connections loose or corroded. 3. Cl ean and check connections for good contact. 4. Defective ignition sw itch. 4. Contact authorized SNA PPER dealer. Engine Will Not Start ...

  • Snapper ZMT2500KH, ZM5201M, ZM6101M - page 22

    22 TROUBLESHOOTING PROBLEM PROBA BLE CA USE CORRECTIVE A CTION T ractor Will Not Move 1. Motion control lev ers in the neutral “N” posit ion. 1. Mov e control levers to desired speed. Loss Of Traction 2. R o ll r e le as e lever is i n “R OL L ” po s it io n . 2. Mov e roll release lever to the engaged position. 3. Low transmission hy draul ...

  • Snapper ZMT2500KH, ZM5201M, ZM6101M - page 23

    23 SERVICE SCHEDULE ITEM SERVICE PERFO RMED REF. EA CH USE 5 HRS 25 HRS 50 HRS 100 HRS EA CH SEA SON Engine Oil Check Oil Level Page 6 X Initial Oil Change Page 10 X Periodic Oil Change Page 11 X* A ir Pre-Cleaner Clean Sponge Elem ent Engine Manual & Page 11. X** A ir Cleaner Clean or Replace Engine Manual. X** Spark Plug Replace Engine Manual ...

  • Snapper ZMT2500KH, ZM5201M, ZM6101M - page 24

    24 2 YEA R LIMITED WARRA NTY For two (2) y ears f rom purc hase date for the original pur chaser's us e, SNA PPER , through any authoriz ed SNA PPER dealer will replace, f ree of charge ( except for taxes where applicable), any part or parts f ound upon exam ination by the fac tory at McDonough, Geor gia, to be defective in m aterial or workm ...

  • Snapper ZMT2500KH, ZM5201M, ZM6101M - page 25

    25 PRIMARY MA INTENA NCE ...

  • Snapper ZMT2500KH, ZM5201M, ZM6101M - page 26

    26 PRIMARY MA INTENA NCE ...

  • Snapper ZMT2500KH, ZM5201M, ZM6101M - page 27

    27 PRIMARY MA INTENA NCE ...

  • Snapper ZMT2500KH, ZM5201M, ZM6101M - page 28

    28 PRIMARY MA INTENA NCE ...

  • Snapper ZMT2500KH, ZM5201M, ZM6101M - page 29

    29 NOTES ...

  • Snapper ZMT2500KH, ZM5201M, ZM6101M - page 30

    30 NOTES ...

  • Snapper ZMT2500KH, ZM5201M, ZM6101M - page 31

    31 NOTES ...

  • Snapper ZMT2500KH, ZM5201M, ZM6101M - page 32

    32 Safety Instructions & Operator’s Manual for M ID MOUNT Z-RIDER ZERO TURNING HYDRO DRIVE SERIES 0 POWER UNIT MODELS ZMT2500KH MOWER UNIT MODELS ZM5200M ZM6100M IMPORTANT Snapper products are built using engines that meet or exceed all a pplicable emissions requirements on the date manufactured. The labels on thos e engines contain very impo ...

Fabbricante Snapper Categoria Lawn Mower

I documenti che otteniamo dal fabbricante del dispositivoSnapper ZMT2500KH, ZM5201M, ZM6101M possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Snapper
- manuali per l’uso ZMT2500KH, ZM5201M, ZM6101M
- schede prodotto Snapper
- opuscoli
- o etichette energetiche Snapper ZMT2500KH, ZM5201M, ZM6101M
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Snapper ZMT2500KH, ZM5201M, ZM6101M.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Snapper ZMT2500KH, ZM5201M, ZM6101M, manuali di manutenzione, brevi manuali o manuali utente Snapper ZMT2500KH, ZM5201M, ZM6101M. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Snapper ZMT2500KH, ZM5201M, ZM6101M.

Manuali per l’uso simili

Manuale completo del dispositivo Snapper ZMT2500KH, ZM5201M, ZM6101M, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Snapper ZMT2500KH, ZM5201M, ZM6101M dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Snapper ZMT2500KH, ZM5201M, ZM6101M.

Il manuale per l’uso completo Snapper, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Snapper ZMT2500KH, ZM5201M, ZM6101M - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Snapper ZMT2500KH, ZM5201M, ZM6101M, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Snapper ZMT2500KH, ZM5201M, ZM6101M che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Snapper ZMT2500KH, ZM5201M, ZM6101M - che ci dovrebbe aiutare nei primi passi durante l'uso Snapper ZMT2500KH, ZM5201M, ZM6101M
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Snapper ZMT2500KH, ZM5201M, ZM6101M
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Snapper ZMT2500KH, ZM5201M, ZM6101M in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Snapper ZMT2500KH, ZM5201M, ZM6101M?

Utilizza il modulo sottostante

Se non hai risolto il problema con Snapper ZMT2500KH, ZM5201M, ZM6101M con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Snapper ZMT2500KH, ZM5201M, ZM6101M è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)