-
Chicago Electric 66910 - page 1
CHIPPER SHREDDER 2.5 HP Model 66910 SEt uP anD OPERa tIng InStRuCtIOnS Visit our website at: http://www .harborfreight.com Read this material before using this product. Failure to do so can result in serious injury . Sa VE tHIS Manual. Copyright © 2009 by Harbor Freight T ools ® . All rights reserved. No portion of this manual or any artwork cont ...
-
Chicago Electric 66910 - page 2
Page 2 For technical questions, please call 1-800-444-3353. SKU 66910 Sa VE tHIS Manual Keep this manual for the safety warnings and precautions, assembly , operating, inspection, maintenance and cleaning procedures. Write the product’ s serial number in the back of the manual (or month and year of purchase if product has no number). Keep this ma ...
-
Chicago Electric 66910 - page 3
Page 3 For technical questions, please call 1-800-444-3353. SKU 66910 T able A shows the correct size to use 3. depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number , the heavier the cord. T o reduce the risk of disconnection of appliance cord from the extension cord during oper ...
-
Chicago Electric 66910 - page 4
Page 4 For technical questions, please call 1-800-444-3353. SKU 66910 to install the proper wall outlet. Do not change the equipment plug, extension cord receptacle, or extension cord plug in any way . This design is referred to as double-insulated, indicated by . W ARNING: Handling the cord on this 9. product will expose you to lead, a chemical kn ...
-
Chicago Electric 66910 - page 5
Page 5 For technical questions, please call 1-800-444-3353. SKU 66910 for misalignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other condition that may affect its operation. Any part that is damaged should be properly repaired or ...
-
Chicago Electric 66910 - page 6
Page 6 For technical questions, please call 1-800-444-3353. SKU 66910 factors which cannot be built into this product, but must be supplied by the operator . Sa VE tHESE InStRuCtIOnS. SPECIFICa tIOnS Electrical Requirements 120V~ / 60Hz / 15A Motor Speed: 3460 RPM Cutting Capacity 1-1/4” Diameter Maximum Safety Features Internal Safety Cut-Off Sw ...
-
Chicago Electric 66910 - page 7
Page 7 For technical questions, please call 1-800-444-3353. SKU 66910 REV 10h Phase 1 note: Leave Bolts (28, 32) only nger tight until the end of Phase 2. Place cupped side of Curved W ashers (27) against legs (24, 26) during assembly . Place Axles (25) into Legs (24, 26). 1a. note the position of left and Right legs in diagram. Secure front Axl ...
-
Chicago Electric 66910 - page 8
Page 8 For technical questions, please call 1-800-444-3353. SKU 66910 Phase 2 2a. with Main Housing (14) facing down. Main Housing may bend if dropped. Flip Leg assembly over , and squeeze 2b. legs together to allow them to be inser ...
-
Chicago Electric 66910 - page 9
Page 9 For technical questions, please call 1-800-444-3353. SKU 66910 Phase 3 Place the Hopper (1) onto the Main 3a. Housing (14), lining up the three holes in the Main Housing. Secure the Hopper in place using three W ashers (8), Spring W ashers (6) and Safety Screws (7). ? ...
-
Chicago Electric 66910 - page 10
Page 10 For technical questions, please call 1-800-444-3353. SKU 66910 Product Features POWER SWItCH (42) CIRCuIt BREaKER (39) FEED StICK (76) FIguRE D HOPPER (1) POWER CORD (37) tIE-DOWn KnOBS (1 1) CHutE (67) FIguRE E MaIn HOuSIng (14) OPERa tIng InStRuCtIOnS Read the EntIRE IMPORt ant SaFEty InFORMa tIOn section at the beginning of this manual i ...
-
Chicago Electric 66910 - page 11
Page 1 1 For technical questions, please call 1-800-444-3353. SKU 66910 Do not force the Chipper Shredder . Let 8. the natural suction process take in the material to be cut. Always stand clear and to the side of the Chute (67). (See Figure E.) Without putting your hands into the 9. Hopper (1), slowly drop the material in (one branch at a time). Th ...
-
Chicago Electric 66910 - page 12
Page 12 For technical questions, please call 1-800-444-3353. SKU 66910 MaIntEnanCE anD SER VICIng Procedures not specically explained in this manual must be performed only by a qualied technician. tO PREVEnt SERIOuS InJuR y FROM aCCIDEnt al OPERa tIOn OR ElECtRIC SHOCK: t urn the Power Switch (42) of the Chipper Shredder to its “OFF” posi ...
-
Chicago Electric 66910 - page 13
Page 13 For technical questions, please call 1-800-444-3353. SKU 66910 tROuBlESHOOtIng tO PREVEnt SERIOuS InJuR y FROM aCCIDEnt al OPERa tIOn OR ElECtRIC SHOCK: t urn the Power Switch (42) of the Chipper Shredder to its “OFF” position and unplug the unit from its electrical outlet before performing any inspection, maintenance, or cleaning proce ...
-
Chicago Electric 66910 - page 14
Page 14 For technical questions, please call 1-800-444-3353. SKU 66910 P aRtS lISt Part Description Qty . 1 Hopper 1 2 Hopper Flap 1 3 1 4 Screw 3 5 Lock Nut 3 6 Flat W asher 3 7 Safety Screw 3 8 W asher 3 9 Cover 2 10 Nut 2 11 T ie-Down Knob 2 13 2 14 Main Housing 1 15 1 16 Spring W asher ...
-
Chicago Electric 66910 - page 15
Page 15 For technical questions, please call 1-800-444-3353. SKU 66910 REV 10g aSSEMBl y DIagRaM nOtE: 5mm allen Wrench (79) not shown. 6mm allen Wrench (80) not shown. 14mm-17mm Wrench (82) not shown. ...
-
Chicago Electric 66910 - page 16
Page 16 For technical questions, please call 1-800-444-3353. SKU 66910 lIMItED 90 Da y W aRRanty Ha rb o r Fr ei gh t T oo ls Co. mak e s ev er y ef for t to assure that its product s meet high quali ty and dur abil ity stand ard s, an d warr ant s to the ori gina l purchaser that this product is free from defects in materials and workmanship for t ...
Hai una domanda su Chicago Electric 66910?
Utilizza il modulo sottostante
Se non hai risolto il problema con Chicago Electric 66910 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Chicago Electric 66910 è probabile che voglia condividere il modo di risolverlo.