Italiano dropdown-ico

Manuale per l’uso Cisco Systems 8xDMT

32 pagine 0.26 mb
Scarica

Vai alla pagina of 32

Summary
  • Cisco Systems 8xDMT - page 1

    1 Cisco IOS Release 12.1(6)DA Octal-Port DMT ATU-C Line Card This feature module describes the Cisco IOS support for the octal-port DMT A TU-C (8xDMT) line card. It includes information on new and modif ied commands. This document includes the following sections: • Feature Overvie w , page 1 • Supported Platforms, page 4 • Supported Standards ...

  • Cisco Systems 8xDMT - page 2

    Octal-Port DMT ATU-C Line Card Feature Overview 2 Cisco IOS Release 12.1(6)DA Benefits G.hs Support (ITU G.994.1) G.hs support is provided through both the MIB and the CLI. Features from G.hs that are supported include: • Enabling/disabling all or one of the following modes. – G.dmt – T1.413 Issue 2 – G.lite • Setting auto mode defers the ...

  • Cisco Systems 8xDMT - page 3

    Octal-Port DMT ATU-C Line Card Feature Overview 3 Cisco IOS Release 12.1(6)DA Note The original option, which generates a minor alarm when conf igured minimum bit rates are not met, is conf igured by default in DSL prof iles. The default conf iguration is no dmt minrate-blocking . • dmt rate-adaptation The dmt rate-adaptation command monitors the ...

  • Cisco Systems 8xDMT - page 4

    Octal-Port DMT ATU-C Line Card Supported Platforms 4 Cisco IOS Release 12.1(6)DA Supported Platforms DSLAMs This feature supports the 8xDMT line card on the Cisco 6015, Cisco 6160, and Cisco 6260 platforms with NI-2. T able 1 details the total av ailable ADSL modem connections for each chassis. The 8xDMT is designed for use with the Cisco 6015, Cis ...

  • Cisco Systems 8xDMT - page 5

    Octal-Port DMT ATU-C Line Card Supported Standards, MIBs, and RFCs 5 Cisco IOS Release 12.1(6)DA Supported Standards, MIBs, and RFCs Standards • ANSI T1.413-Issue 2, Category 1 only • ANSI T1.413-Issue 2, Annex F (Reduced NEXT) • Uni versal T est & Operations PHY for A TM, Lev el 2; A standard for transport of A TM cells ov er a 16-bit pa ...

  • Cisco Systems 8xDMT - page 6

    Octal-Port DMT ATU-C Line Card Prerequisites 6 Cisco IOS Release 12.1(6)DA Prerequisites T o use the 8xDMT feature, you must hav e one of the following DSLAMs with the 8xDMT line card, and IOS 12.1(6) or abov e installed: • Cisco 6015 • Cisco 6160 • Cisco 6260 Configuration Tasks See the follo wing sections for conf iguration tasks for the 8x ...

  • Cisco Systems 8xDMT - page 7

    Octal-Port DMT ATU-C Line Card Configuration Tasks 7 Cisco IOS Release 12.1(6)DA Creating and Associating a DSL Profile with Each Port Before starting this conf iguration task, install the 8xDMT line card. Refer to the Octal-P ort DMT A TU-C Line Car d FR U Installation and Conf iguration Notes for information on installing the 8xDMT line card. Sta ...

  • Cisco Systems 8xDMT - page 8

    Octal-Port DMT ATU-C Line Card Monitoring and Maintaining the 8xDMT Line Card 8 Cisco IOS Release 12.1(6)DA Troubleshooting Tips Cisco provides Cisco.com as a starting point for all technical assistance. Customers and partners can obtain documentation, troubleshooting tips, and sample conf igurations from online tools. For Cisco.com re gistered use ...

  • Cisco Systems 8xDMT - page 9

    Octal-Port DMT ATU-C Line Card Configuration Examples 9 Cisco IOS Release 12.1(6)DA Configuration Examples The following e xample shows a prof ile named 8xDMT2 being created. The prof ile uses the default prof ile values for any parameters not specif ied. Current configuration : 7019 bytes ! version 12.1 no service pad service timestamps debug upti ...

  • Cisco Systems 8xDMT - page 10

    Octal-Port DMT ATU-C Line Card Command Reference 10 Cisco IOS Release 12.1(6)DA Command Reference This section documents the new and modif ied commands that are specif ic to the8xDMT feature. All other commands used with this feature are documented in the Command Refer ence for Cisco DSLAMS with NI-2 . For information on other Cisco IOS commands th ...

  • Cisco Systems 8xDMT - page 11

    Octal-Port DMT ATU-C Line Card alarms 11 Cisco IOS Release 12.1(6)DA alarms T o enable alarms in prof ile command mode, use the alarms command. T o disable alarms, use the no form of the command. alarms Syntax Description This command has no keyw ords or arguments. Defaults Disabled. Command Modes Prof ile conf iguration. Command History Usage Guid ...

  • Cisco Systems 8xDMT - page 12

    Octal-Port DMT ATU-C Line Card alarms 12 Cisco IOS Release 12.1(6)DA Note The alarms command has no effect on critical alarms, major alarms, or minor alarms related to subsystems other than the DSL subscriber ports. Examples In this example, the command enables alarms for the def ault prof ile: DSLAM# configure terminal DSLAM(config)# dsl-profile d ...

  • Cisco Systems 8xDMT - page 13

    Octal-Port DMT ATU-C Line Card dmt bitrate 13 Cisco IOS Release 12.1(6)DA dmt bitrate T o set the maximum and minimum allo wed bit rates for the fast or interleav ed DMT prof ile parameters, use the dmt bitrate prof ile conf iguration command. T o reset this command to the default value, use the no form of this command. dmt bitrate maximum {fast | ...

  • Cisco Systems 8xDMT - page 14

    Octal-Port DMT ATU-C Line Card dmt bitrate 14 Cisco IOS Release 12.1(6)DA Caution This command causes the port to retrain when you change the value of the bit rate parameter . Setting a parameter to its current value does not cause a retrain. If a port is training when you change the parameter , the port stops training and retrains to the new param ...

  • Cisco Systems 8xDMT - page 15

    Octal-Port DMT ATU-C Line Card dmt check-bytes 15 Cisco IOS Release 12.1(6)DA dmt check-bytes T o set upstream and do wnstream FEC check (redundancy) bytes, use the dmt-checkbytes prof ile conf iguration command. T o reset this command to the default value, use the no form of this command. dmt check-bytes {fast | interleaved} downstream bytes upstr ...

  • Cisco Systems 8xDMT - page 16

    Octal-Port DMT ATU-C Line Card dmt check-bytes 16 Cisco IOS Release 12.1(6)DA Related Commands None. ...

  • Cisco Systems 8xDMT - page 17

    Octal-Port DMT ATU-C Line Card dmt margin 17 Cisco IOS Release 12.1(6)DA dmt margin T o set upstream and do wnstream signal-to-noise ratio (SNR) margins for a DMT prof ile, use the dmt margin command. T o reset this command to the default value, use the no form of this command. dmt margin downstr eam dmt-margin upstr eam dmt-margin Syntax Descripti ...

  • Cisco Systems 8xDMT - page 18

    Octal-Port DMT ATU-C Line Card dmt minrate-blocking 18 Cisco IOS Release 12.1(6)DA dmt minrate-blocking T o force a port not to retrain when actual bit rates fall below the v alues conf igured in the dmt bitrate minimum command, use the dmt minrate-blocking command. T o disable dmt minrate-blocking, use the no form of the command. dmt minrate-block ...

  • Cisco Systems 8xDMT - page 19

    Octal-Port DMT ATU-C Line Card dmt overhead-framing 19 Cisco IOS Release 12.1(6)DA dmt overhead-framing T o set the ov erhead framing mode, use the dmt overhead-framing command.T o reset this command to the default v alue, use the no form of this command. dmt overhead-framing {mode0 | mode1 | mode2 | mode3 } Syntax Description Defaults Mode3. Comma ...

  • Cisco Systems 8xDMT - page 20

    Octal-Port DMT ATU-C Line Card dmt overhead-framing 20 Cisco IOS Release 12.1(6)DA • Mode 2—Reduced ov erhead framing with separate fast and sync bytes in the fast and interlea ved latency b uffers respecti vely . • Mode 3—Reduced ov erhead framing with merged fast and sync bytes using either the f ast or interleav ed latency b uffer . Note ...

  • Cisco Systems 8xDMT - page 21

    Octal-Port DMT ATU-C Line Card dmt rate-adaptation enable 21 Cisco IOS Release 12.1(6)DA dmt rate-adaptation enable DMT rate adaptation monitors upstream and downstream DMT ports for signal-to-noise ratio (SNR) margins during specif ied time intervals. If an unacceptable SNR mar gin is detected, the port is retrained at a lo wer bit rate to improve ...

  • Cisco Systems 8xDMT - page 22

    Octal-Port DMT ATU-C Line Card dmt rate-adaptation interval 22 Cisco IOS Release 12.1(6)DA dmt rate-adaptation interval T o change the interv als during which a DMT port is monitored for signal-to-noise ratio (SNR) margins, use the dmt rate adaptation interval command in DSL prof ile conf iguration mode. T o disable dmt rate adaptation interval , u ...

  • Cisco Systems 8xDMT - page 23

    Octal-Port DMT ATU-C Line Card dmt rate-adaptation interval 23 Cisco IOS Release 12.1(6)DA Usage Guidelines Use the dmt rate-adaptation interval to specify the frequenc y at which line margins are checked on a DMT port. The dmt rate-adaptation interval command works in conjunction with the dmt rate-adaptation margin command. If the actual SNR margi ...

  • Cisco Systems 8xDMT - page 24

    Octal-Port DMT ATU-C Line Card dmt rate-adaptation margin 24 Cisco IOS Release 12.1(6)DA dmt rate-adaptation margin T o conf igure the minimum acceptable SNR margins on a DMT port, which force the port to retrain when bad margins e xist for the duration of the dmt rate-adaptation interval, use the dmt rate adaptation margin command in DSL prof ile ...

  • Cisco Systems 8xDMT - page 25

    Octal-Port DMT ATU-C Line Card slot 25 Cisco IOS Release 12.1(6)DA slot T o provision a slot for a specif ic card type, or to change the line coding for a f lexi line card, use the slot command. slot slot# car dtype Syntax Description Defaults None. Command Modes Global conf iguration. Command History slot# The number of the slot you want to provis ...

  • Cisco Systems 8xDMT - page 26

    Octal-Port DMT ATU-C Line Card slot 26 Cisco IOS Release 12.1(6)DA Usage Guidelines Use the slot command to provision a slot for a line card. Card mismatch error conditions include the follo wing: • A line card is already installed in the specif ied slot • The specif ied slot contains one type of card but is provisioned for another type If you ...

  • Cisco Systems 8xDMT - page 27

    Octal-Port DMT ATU-C Line Card Glossary 27 Cisco IOS Release 12.1(6)DA Glossary A ADSL Asymmetric Digital Subscriber Line. A digital subscriber line (DSL) technology in which the transmission of data from server to client is much faster than the transmission from the client to the server . ADSL Transmission Unit—central office See A TU-C . ADSL T ...

  • Cisco Systems 8xDMT - page 28

    Octal-Port DMT ATU-C Line Card Glossary 28 Cisco IOS Release 12.1(6)DA DDTS Cisco Distributed Defect T racking System. digital signal level 3 See DS3 . Distributed Defect Tracking System See DDTS . DS3 digital signal le vel 3. Framing specif ication used for transmitting digital signals at 44.736 Mbps on a T3 facility . DSLAM Digital Subscriber Lin ...

  • Cisco Systems 8xDMT - page 29

    Octal-Port DMT ATU-C Line Card Glossary 29 Cisco IOS Release 12.1(6)DA IP address The 32-bit address assigned to hosts that want to participate in a TCP/IP Internet. ITU The International T elecommunications Union; a telecommunications standards body . L LCD Loss of Cell Delineation LODS Loss Of Delay Synchronization LOF Loss Of Frame. loopback A d ...

  • Cisco Systems 8xDMT - page 30

    Octal-Port DMT ATU-C Line Card Glossary 30 Cisco IOS Release 12.1(6)DA router A system responsible for making decisions about which of sev eral paths network (or Internet) traf f ic will follo w . T o do this, it uses a routing protocol to gain information about the network and algorithms to choose the best route based on sev eral criteria known as ...

  • Cisco Systems 8xDMT - page 31

    Octal-Port DMT ATU-C Line Card Glossary 31 Cisco IOS Release 12.1(6)DA U upstream rate The line rate for message or data transfer from the source machine to a destination machine on the network. Also see do wnstream rate. V VC V irtual circuit. A logical circuit created to ensure reliable communication between two network devices. A virtual circuit ...

  • Cisco Systems 8xDMT - page 32

    Octal-Port DMT ATU-C Line Card Glossary 32 Cisco IOS Release 12.1(6)DA ...

Fabbricante Cisco Systems Categoria Network Router

I documenti che otteniamo dal fabbricante del dispositivoCisco Systems 8xDMT possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Cisco Systems
- manuali per l’uso 8xDMT
- schede prodotto Cisco Systems
- opuscoli
- o etichette energetiche Cisco Systems 8xDMT
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Cisco Systems 8xDMT.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Cisco Systems 8xDMT, manuali di manutenzione, brevi manuali o manuali utente Cisco Systems 8xDMT. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Cisco Systems 8xDMT.

Manuali per l’uso simili

Manuale completo del dispositivo Cisco Systems 8xDMT, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Cisco Systems 8xDMT dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Cisco Systems 8xDMT.

Il manuale per l’uso completo Cisco Systems, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Cisco Systems 8xDMT - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Cisco Systems 8xDMT, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Cisco Systems 8xDMT che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Cisco Systems 8xDMT - che ci dovrebbe aiutare nei primi passi durante l'uso Cisco Systems 8xDMT
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Cisco Systems 8xDMT
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Cisco Systems 8xDMT in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Cisco Systems 8xDMT?

Utilizza il modulo sottostante

Se non hai risolto il problema con Cisco Systems 8xDMT con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Cisco Systems 8xDMT è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)