-
Makita 4303C - page 1
Electronic Jig Saw Length of stroke MODEL 4303C weight I Net Strokes Overall per minute length Max. cutting capacities Wood Steel INSTRUCTION MANUAL SPECIFICATIONS 2.5 kg 'Omm I I!$: 1 1,000 - 3,000 I 219mm (1") 1 (2.318") (8-518") 1 (5.5 Ibs) 26 mm Manufacturer reserves the right to change specifications without notice. Note: S ...
-
Makita 4303C - page 2
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries ...
-
Makita 4303C - page 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don’t carry tool with finger on switch. Be sure switch is OFF when plugging in. 16. EXTENSION CORDS. Make sure your extension cord is in good condition. When using an ...
-
Makita 4303C - page 4
VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user - as well as damage to the tool. If in doubt, DO NOT PLUG IN T ...
-
Makita 4303C - page 5
Installing Makita jig saw blade CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the blade. Use the hex wrench to loosen the bolt. With the blade teeth facing forward, insert the blade into the blade holder as far as it will go. Make sure that the back edge of the blade fits into the roller and tigh ...
-
Makita 4303C - page 6
Installing universal shank jig saw blade CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the blade. If the universal blade clamp is used, you can use blades of other makes which have a universal shank like the one shown in the figure, with a blade width of 6.35 mm (1/4"). Insert the blade into ...
-
Makita 4303C - page 7
Straight line or orbital cutting action I Conventional jig saws cut with a straight line action, that is, the blade moves only up and down in a straight line. Your saw also cuts in this manner but, for softer workpieces, an orbital cutting action can be selected. Soft workpieces like wood and plastic permit deep penetration of indivi- dual saw teet ...
-
Makita 4303C - page 8
Speed change To adjust the tool speed, turn the speed change dial. The tool speed can be adjusted between 1,000 and 3,000 strokes per minute. Number 1 The reference table on the right denotes the relationship between the number set- tings on the speed change dial and the approximate strokes per minute at that setting. Strokes per minute 1,000 1 Ref ...
-
Makita 4303C - page 9
Operation Turn the tool on and wait until the blade attains full speed. Then rest the base flat on the workpiece and gently move the tool forward along the previously marked cut- ting line. When cutting curves, advance the tool very slowly. I . I CAUTION : Failure to hold the tool base flush with the workpiece may cause blade breakage. Bevel cuttin ...
-
Makita 4303C - page 10
I I Front flush cuts Loosen the bolt on the back of the base with the hex wrench, then slide the base backwards. Check the contact between the back edge of the blade and the roller, then secure the bolt. Plunge cutting Starting a cut at other than the edge of the workpiece without first drilling a starting hole requires a "plunge cut". Th ...
-
Makita 4303C - page 11
Using guide rule (Rip fence) When cutting widths of under 150 mm (6") repeatedly, use of the guide rule will assure fast, clean, straight cuts. ~ I To attach the guide rule (rip fence), secure the rule holder to the base with the screw (do not tighten). Insert the guide rule between the base and the rule holder. Now tighten the screw with the ...
-
Makita 4303C - page 12
To attach the circular guide, use the pin, inserting it in the center hole (arrow) and secure it with the threaded knob. Then slide the base of the tool forwards. The circular guide attaches to the base of the tool in the same manner as the guide rule (rip fence). Metal cutting Always use a suitable coolant (cutting oil) when cutting metal. Failure ...
-
Makita 4303C - page 13
MAINTENANCE CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Ma ...
-
Makita 4303C - page 14
Jig saw blade H 1.5 - 3 mm thick 11/16’’ - 1/8”) H 1 - 6 mm thick 1 - 3 mm thick (3164‘’ - 114“) 13/64” - 1/8”) H 3 - 55 mm thick (1/8” - 2-1/8”) H 3 - 30 mm thick 3 - 10 mm thick 11/8” - l-l/8”) 11/8” - 3/8”) Application Plastics Aluminum Mild steel 1.5 - 3 mm thick 1 - 6 mm thick 1 - 3 mm thick 11/16’ - 1/8”) 13/64 ...
-
Makita 4303C - page 15
May-19--'94 US ELECTRONIC JIG SAW Model 4303C Note: The switch and other part configurations may differ from country to country. 15 ...
-
Makita 4303C - page 16
MODEL 4303C ZD DESCRIPTION =E 1 2 3 4 5 6 7 8 9 0 11 2 3 14 18 19 20 21 22 23 24 25 26 2, 28 29 30 31 32 33 34 35 36 31 38 39 40 - 1 1 1 1 1 1 4 1 1 1 3 1 1 1 1 1 1 1 1 1 1 ITEM NO NO USED MA1 41 42 43 44 45 46 47 48 49 50 51 52 53 51 55 56 57 58 59 60 61 62 63 64 55 66 67 66 69 70 72 75 75 79 80 ~ May-19-'94 US IKSCRIPTION Pan Head Screw MSr2 ...
Hai una domanda su Makita 4303C?
Utilizza il modulo sottostante
Se non hai risolto il problema con Makita 4303C con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Makita 4303C è probabile che voglia condividere il modo di risolverlo.