Italiano dropdown-ico

Manuale per l’uso Chamberlain 8200 1/2 HP

40 pagine 1.01 mb
Scarica

Vai alla pagina of 40

Summary
  • Chamberlain 8200 1/2 HP - page 1

    Garage Door Opener Model 8200 Series 1/2 HP For Residential Use Only Owner's Manual ■ Please read this manual and t he enclosed safety materials carefully! ■ Fasten t he manual near the garage door aft er installation. ■ The door WILL NOT CLOSE unless the Prot ector System ® is connected and properly aligned. ■ Periodic checks of the ...

  • Chamberlain 8200 1/2 HP - page 2

    Start by reviewing t hese important safety alert symbols 2 Contents Page A review of safety alert symbols ..................................2 You'll need tools ...........................................................3 Safety information regarding garage door locks and ropes ..........................................................3 Testing ...

  • Chamberlain 8200 1/2 HP - page 3

    Pliers Wire Cutters Claw Hammer Hack Saw Screwdriver Adjustable End Wrench 1/2" and 7/16" Sockets and Wrench Drill Tape Measure 2 1 Stepladder Pencil 3/16", 5/16" and 5/32" Drill Bits Carpenter's Level Y ou'll Need T ools During assembly, installation and adjustment of the opener, instructions will call for hand t ...

  • Chamberlain 8200 1/2 HP - page 4

    4 Safety Reversing Sensor Horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, steel, aluminum, door with glass panels, etc.). See page 24 for details. Support bracket & fastening hardware is required. See page 17. — — — — — — — — Door Center Header Wall Safety Reversing Sensor Floor must be ...

  • Chamberlain 8200 1/2 HP - page 5

    Safety Reversing Sensor FINISHED CEILING Support bracket & fastening hardware is required. See page 17. Safety Reversing Sensor Header Wall Access Door Gap between floor and bottom of door must not exceed 1/4". 5 Closed Position Belt Pulley Bracket Header Bracket Trolley Straight Door Arm Manual Release Rope & Handle Door Bracket Curve ...

  • Chamberlain 8200 1/2 HP - page 6

    Trolley Header Bracket Hanging Brackets Belt Curved Door Arm Section Straight Door Arm Section Safety Labels and Literature Light Lens (2) Rail Brace (3) T-rail Center Section (each) (2) T-rail End Section (2) UP CEILING MOUNT ONLY Belt Cap Retainer Door Bracket 8200 (1), 8200-2 (2), 8200-2K (2) 8200-2K 2-Conductor Bell Wire White & White/Red B ...

  • Chamberlain 8200 1/2 HP - page 7

    Lock Washer 5/16" (4) Nut 5/16"-18 (6) Clevis Pin 5/16"x2-3/4" (1) NOTICE Handle Insulated Staples (10) ASSEMBLY INSTALLATION Dry Wall Anchors (2) Clevis Pin 5/16"x1" (1) Hex Screw 5/16"-18x7/8" (4) Rope Trolley Clip (1) Lock Nut 1/4"-20x7/16" (12) Nut 5/16"-18 (4) Washered Screw 5/16"-18x ...

  • Chamberlain 8200 1/2 HP - page 8

    8 Assembly St ep 1 Assemble the T -rail & Attach the Belt Pulley Bracket T-RAIL BACK (TO OPENER) T-RAIL FRONT (TO DOOR) Belt pulley bracket attaches to FRONT END of T-rail T-rail (End Section) T-rail (Center Section) Carriage Bolt 1/4"-20x1/2" T-rail (End Section) Square Carriage Bolt Hole 1/4" Lock Nut Bracket Lock Washer 5/16&q ...

  • Chamberlain 8200 1/2 HP - page 9

    Assembly St ep 2 Install the Trolley on the T -rail 9 • As a temporary stop, insert a screwdriver into the hole in the front end of the T-rail. • Slide the trolley assembly along the rail to the screwdriver stop. If trolley hits against any nuts on the T-rail, the bolts and nuts were attached from the wrong side and must be repositioned. Review ...

  • Chamberlain 8200 1/2 HP - page 10

    Assembly St ep 4 Install the Belt & Set the Belt T ension Serious injury can result if fingers become entangled in moving opener sprocket. Attach belt cap retainer securely. Never operate opener while your hand is near the opener sprocket. Nut Ring Trolley Threaded Shaft Nut Ring Slots Trolley Square End Opener Sprocket 10 • Drop the notched ...

  • Chamberlain 8200 1/2 HP - page 11

    Hex Screws # 8 x 3/8" Belt Cap Retainer Opener Sprocket Mounting Plate Assembly St ep 5 Attach the Belt Cap Retainer IMPORT ANT INST ALLA TION INSTRUCTIONS T o reduce the risk of severe injury or deat h to persons: 1. READ AND FOLLOW ALL INST ALLA TION INSTRUCTIONS. 2. Install only on a properly balanced and lubricated garage door. An improper ...

  • Chamberlain 8200 1/2 HP - page 12

    • Open your door to the highest point of travel as shown. Draw an intersecting horizontal line on the header wall 2" above the high point. This height will provide travel clearance for the top edge of the door. Header Wall Ceiling Track Highest Point of Travel Door 2" 12 Proceed to Step 2, page 14. Door Track Header Wall Highest Point o ...

  • Chamberlain 8200 1/2 HP - page 13

    Header Wall Vertical Centerline Vertical Centerline of Garage Door 2x4 Unfinished Ceiling Structural Supports 2x4 OPTIONAL CEILING MOUNT FOR HEADER BRACKET • Close the door and mark the inside vertical centerline of your garage door. Extend the line onto the header wall above door. If headroom clearance is minimal, you can install the header brac ...

  • Chamberlain 8200 1/2 HP - page 14

    Lag Screws 5/16"x9x1-5/8" Highest Point of Travel (of Garage Door) Vertical Center Line Header Wall Garage Door UP CEILING MOUNT ONLY Wall Mounting Holes Optional Wall Mounting Holes The nail hole is for positioning only. You must use lag screws to mount the header bracket. UP CEILING MOUNT ONLY Door Spring Header Bracket 2x4 Structural S ...

  • Chamberlain 8200 1/2 HP - page 15

    Header Bracket Belt Pulley Bracket Temporary Support Header Wall Garage Door , Liftmaster Synchro Drive Tee Rail to Header Bracket 5/16/92 T-rail Clevis Pin 5/16"x2-3/4 " Ring Fastener Header Bracket Belt Pulley Bracket T-rail • Position the opener on the garage floor below the header bracket. Use packing material as a protective base. ...

  • Chamberlain 8200 1/2 HP - page 16

    Installation St ep 4 Position the Opener Follow instructions which apply to your door type as illustrated. To prevent damage to steel, aluminum, fiberglass or glass panel doors, do not rest the opener on the door without using a 2x4. SECTIONAL Door & ONE-PIECE Door with T rack A 2x4 laid flat is convenient for setting an ideal door-to-T-rail di ...

  • Chamberlain 8200 1/2 HP - page 17

    Installation St ep 5 Hang the Opener Two representative installations are shown. Yours may be different. Hanging brackets should be angled, Figure 1, to provide rigid support. On finished ceilings, Figure 2, attach a sturdy metal bracket to structural supports before installing the opener. The bracket and fastening hardware are not supplied. • Me ...

  • Chamberlain 8200 1/2 HP - page 18

    18 Installation St ep 6 Install the Multi-Function Door Control Panel 6ABx1-1/4" Screw Multi-Function Door Control Insulated Staples Dry Wall Anchors Screw 6-32x1" Hardware Shown Actual Size Outside Keylock Accessory Connections To opener terminal screws: white to 2; white/red to 1 WARNING Opener Terminal Screws Antenna Right Panel of Ope ...

  • Chamberlain 8200 1/2 HP - page 19

    • Install a 75 watt maximum light bulb in each socket. The lights will turn ON and remain lit for approximately 4-1/2 minutes when power is connected. Then the lights will turn OFF. • If the bulbs burn out prematurely due to vibration, replace them with "Garage Door Opener" bulbs. • Slide lenses into guides as shown. Snap bottom tab ...

  • Chamberlain 8200 1/2 HP - page 20

    To prevent electrocution, remove power from the garage door opener and from the circuit you plan to use for the permanent connection. To reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn't fit into the outlet y ...

  • Chamberlain 8200 1/2 HP - page 21

    Without a properly working safety reversing sensor, persons (particularly children) could be injured or killed by a closing garage door. Read and follow all instructions. To protect small children, install the safety reversing sensor so that the beam will be no higher than 4"-6" above the garage floor. Disconnect power to the garage door ...

  • Chamberlain 8200 1/2 HP - page 22

    Installation St ep 10 Install the Safety Reversing Sensor 22 FLOOR MOUNT (Right Side) WALL MOUNT (Right Side) DOOR TRACK MOUNT (Right Side) Indicator light Lens Lip Sensor Brack et Door T rac k Sensor Brack et Optional Extension Bracket (See Accessories) Lens Indicator light Attach with concrete anchors (not provided) Inside Garage Wall Indicator l ...

  • Chamberlain 8200 1/2 HP - page 23

    23 Invisible Light Beam Protection Area Sensor Sensor Connect Wire to Opener Terminals Bell Wire Bell Wire Finished Ceiling OPENER TERMINAL SCREWS Sensor Connections Door Control Connections (dotted line) 1 2 3 Figure 6 Wiring the Safety Sensors 1/4"-20x1/2" Carriage bolt Lens Wing nut Figure 5 MOUNTING AND WIRING THE SAFETY SENSORS • S ...

  • Chamberlain 8200 1/2 HP - page 24

    Installation St ep 1 1 Fasten Door Bracket Follow instructions which apply to your door type as illustrated below or on page 25. To prevent damage to steel, aluminum, fiberglass or glass panel doors, always reinforce the inside of the door both vertically and horizontally with an angle iron. A horizontal brace should be long enough to be secured to ...

  • Chamberlain 8200 1/2 HP - page 25

    Horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, aluminum, steel, door with glass panel, etc.). (Not Provided) Header Wall Vertical Centerline of Garage Door — Finished Ceiling — Optional Placement of Door Bracket Header Bracket 2x4 Support Door Bracket For a door with no exposed framing or for the optio ...

  • Chamberlain 8200 1/2 HP - page 26

    Ring Fastener Door Bracket Clevis Pin 5/16"x1-1/4" Curved Door Arm Straight Door Arm Clevis Pin 5/16"x1" Lock Washers 5/16" Nuts 5/16"-18 Door Bracket Screws 5/16"-18x7/8" Manual Release Handle Rope Lock Washers 5/16" Nuts 5/16"-18 Screws 5/16"-18x7/8" Cut This End Inner Trolley Outer Trol ...

  • Chamberlain 8200 1/2 HP - page 27

    Nuts 5/16"-18 Lock Washers 5/16" Ring Fastener Straight Arm Screws 5/16"-18x7/8 Door Bracket Clevis Pin 5/16"x1-1/4" Curved Door Arm Door Arm Fully Open Trolley Door Arm Connector Hole Closed Door Open Door Door with Backward Slant Door Arm Connector Hole Fully Closed Trolley Door Arm All ONE-PIECE Doors Assemble the Door A ...

  • Chamberlain 8200 1/2 HP - page 28

    Ad justment Step 1 Adjust the UP and DOWN Limits Do not make any limit adjustments until the Safety Reversing Sensors are completely installed. 28 Limit adjustment settings regulate the points at which the door will stop when moving up or down. The door will stop in the up direction if anything interferes with door travel. The door will reverse in ...

  • Chamberlain 8200 1/2 HP - page 29

    Ad justment Step 2 Adjust the Force Too much force on the door will interfere with the proper operation of the safety reverse system. The door might not reverse properly when required and could seriously injure or kill someone under it. Do not increase the force beyond the minimum amount required to close the door. Do not use the force adjustments ...

  • Chamberlain 8200 1/2 HP - page 30

    Ad justment Step 4 T est the Safety Reverse System Test: • With the door fully open, place a one-inch board (or a 2x4 laid flat) on the floor, centered under the garage door. • Operate the door in the down direction. The door must reverse on striking the obstruction. Adjustment: If the door stops on the obstruction, it is not traveling far enou ...

  • Chamberlain 8200 1/2 HP - page 31

    Once a Month Manually operate door. If it is unbalanced or binding, call for professional garage door service. Check to be sure door opens and closes fully. Adjust limits and/or force if necessary. (See pages 28 and 29.) Repeat the safety reverse test. Make any necessary adjustments. (See page 30.) Once a Year Oil door rollers, bearings and hinges. ...

  • Chamberlain 8200 1/2 HP - page 32

    To open the door manually: The door should be fully closed if possible. Pull down on the manual release handle and lift the door manually. To reconnect the door to the opener, press the Door Control push bar. Trolley Trolley Release Arm NOTICE Manual Release Handle (Pull Down) Trolley Trolley Release Arm NOTICE Manual Release Handle (Pull Down & ...

  • Chamberlain 8200 1/2 HP - page 33

    KG KG 1 3 9 7 5 1 3 9 7 5 1 2 3 Smart (learn) Button SECURITY ✚ Garage Door Opener Indicator Light RIGHT SIDE PANEL KG KG 1 3 9 7 5 1 3 9 7 5 1 2 3 33 Figure 2 SECURITY ✚ Multi-Function Remote Control Select a Push Button Figure 1 Receiver and Remot e Cont rol Programming Children operating or playing with a garage door opener can injure themse ...

  • Chamberlain 8200 1/2 HP - page 34

    1. Does the opener have electric power? Plug a lamp into the outlet. If it doesn't light, check the fuse box or the circuit breaker. (Some outlets are controlled by a wall switch.) 2. Have you disabled all door locks? Review installation instruction warnings on Page 11. 3. Is there a build-up of ice or snow under the door? The door may be froz ...

  • Chamberlain 8200 1/2 HP - page 35

    Having a Problem? (continued) Situation Probable Cause & Solution The opener strains or maximum force is needed to operate the door: The door may be out of balance or the springs are broken. Close the door and use the manual release rope and handle to disconnect the trolley. Open and close the door manually. A properly balanced door will stay i ...

  • Chamberlain 8200 1/2 HP - page 36

    9 10 11 NOTICE 5 6 UP CEILING MOUNT ONLY 8 7 4 3 2 1 LOCK LIGHT 13 12 2 1 3 3 4 5 10 5 RAIL GREASE NO. 83A4 8 9 7 6 Repair Parts Rail Assembly Parts Installation Parts 36 KEY PART NO. NO. DESCRIPTION 1 1A995 Master link kit 2 41B3869-1 Complete trolley assembly 3 183B112 Rail braces (each) 4 183B111 T-rail – center sections (each) 5 183B113 T-rai ...

  • Chamberlain 8200 1/2 HP - page 37

    Repair Parts Opener Assembly Parts 2 12 10 15 4 3 DN UP Brown Wire (Down) Contact LIMIT SWITCH ASSY. Grey Wire Yellow Wire (Up) Contact Center Limit Contact Drive Gear 11 5 6 7 9 8 9 8 20 14 13 16 1 3 18 19 17 5 KEY PART NO. NO. DESCRIPTION 1 41A4371 Belt cap retainer 2 41A4885-2 Gear and sprocket assy., Complete with: Spring washer Thrust washer R ...

  • Chamberlain 8200 1/2 HP - page 38

    Accessories A vailable for your Opener 38 Outside Keylock: Opens the garage door automatically from outside when remote control is not handy. To Add the Keyless Entry We recommend that you program your password before you install the Keyless Entry. You will not need assistance, and you can test the reception at the mounting location before installa ...

  • Chamberlain 8200 1/2 HP - page 39

    Index Access Door/Outside Quick Release Accessory ............................................................................................4, 5 Electrical Safety Warnings ........................................................................................................................2, 20, 31 Garage Door Testing for balance, binding and s ...

  • Chamberlain 8200 1/2 HP - page 40

    CHAMBERLAIN SER VICE IS ON CALL OUR LARGE SERVICE ORGANIZATION SPANS AMERICA INSTALLATION AND SERVICE INFORMATION IS AS NEAR AS YOUR TELEPHONE SIX DAYS A WEEK. SIMPLY DIAL OUR TOLL FREE NUMBER: 1-800-528-9131 HOURS: (Central Std. Time) 6 A.M. to 7 P.M. Monday through Friday 8 A.M. to 6 P.M. Saturday For professional installation, parts and service, ...

Fabbricante Chamberlain Categoria Garage Door Opener

I documenti che otteniamo dal fabbricante del dispositivoChamberlain 8200 1/2 HP possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Chamberlain
- manuali per l’uso 8200 1/2 HP
- schede prodotto Chamberlain
- opuscoli
- o etichette energetiche Chamberlain 8200 1/2 HP
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Chamberlain 8200 1/2 HP.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Chamberlain 8200 1/2 HP, manuali di manutenzione, brevi manuali o manuali utente Chamberlain 8200 1/2 HP. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Chamberlain 8200 1/2 HP.

Manuali per l’uso simili

Manuale completo del dispositivo Chamberlain 8200 1/2 HP, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Chamberlain 8200 1/2 HP dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Chamberlain 8200 1/2 HP.

Il manuale per l’uso completo Chamberlain, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Chamberlain 8200 1/2 HP - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Chamberlain 8200 1/2 HP, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Chamberlain 8200 1/2 HP che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Chamberlain 8200 1/2 HP - che ci dovrebbe aiutare nei primi passi durante l'uso Chamberlain 8200 1/2 HP
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Chamberlain 8200 1/2 HP
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Chamberlain 8200 1/2 HP in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Chamberlain 8200 1/2 HP?

Utilizza il modulo sottostante

Se non hai risolto il problema con Chamberlain 8200 1/2 HP con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Chamberlain 8200 1/2 HP è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)