-
Yeoman YM-E9001FLA - page 1
Electric Exmoor & Dartmoor Installation and User Instructions For use in Great Britain and the Republic of Ireland. This product is suitable for use in the stated countries. To install the product in other countries it is essential to obtain translated instructions and in some cases the product may require modification. Contact Yeoman Stoves to ...
-
Yeoman YM-E9001FLA - page 2
2 USER INSTRUCTIONS 3 1. Important Information & Health and Safety 3 2. Operating Instructions 4 3. Maintenance 5 4. Removing & Replacing Doors 6 INSTALLATION INSTRUCTIONS 7 Technical Specifications 7 Site Requirements 7 DIMENSIONS FOR FIRE & OPENING Exmoor 6 Dartmoor 6 1. Fitting Stoves 8 2. Fault Finding 8 3. How to Wire a Plug 8 SERV ...
-
Yeoman YM-E9001FLA - page 3
3 USER INSTRUCTIONS HOW TO USE THESE INSTRUCTIONS The contents of Sections 1, 2 and 3 apply to all the models in our Electric Range. The content of Section 4, Remove and Replace Door , gives different instructions for each model type. Select the relevant information for your model. 1. IMPORTANT INFORMATION and HEALTH AND SAFETY ALL APPLIANCES DESCR ...
-
Yeoman YM-E9001FLA - page 4
2. OPERATING INSTRUCTIONS WARNING! Do not operate the appliance if it is damaged or has malfunctioned. If you suspect the appliance is damaged or has malfunctioned call a qualified service engineer to inspect the appliance, and replace any part of the electrical system if necessary, before reuse. GENERAL 2.1 The appliance can be operated by the inf ...
-
Yeoman YM-E9001FLA - page 5
5 1 2 3 4 Maximum Medium Minimum Maximum plus blue & green ame effects Turning On the Heat: 2.13 When turning on the heater you must always press the 1kW button. Do not start the fire using the 2kW setting. 2.14 It is NOT advisable to run the heater without the flame effects switched on. 2.15 Press the 1kW button to turn the fan heater ON. O ...
-
Yeoman YM-E9001FLA - page 6
6 Take care not to damage the plastic screen when replacing the fuel bed. 4 AR2165 4. REMOVING & REPLACING DOORS & REMOVAL OF FUEL BED WARNING: DOOR CASTINGS ARE EXTREMELY HEAVY - SEEK ASSISTANCE BEFORE REMOVAL. Please note: The fuel bed is secured by 2 x screws on the lower panel on the front of the stove. 3 Screws Fuel bed AR2391 Take car ...
-
Yeoman YM-E9001FLA - page 7
7 INSTALLATION INSTRUCTIONS TECHNICAL SPECIFICATIONS SITE REQUIREMENTS ALL INGLENOOK FIREPLACE OPENINGS: For all models the dimensions required for an inglenook installation can be calculated by adding 225mm (9") to the height of the appliance and 150mm (6") to each side. An additional 50mm (2") must be added to the depth to provide ...
-
Yeoman YM-E9001FLA - page 8
1. FITTING STOVES Most stoves are heavy and do not require anchoring to the hearth or floor, but in certain circumstances the appliance can become unstable e.g. when leaning on the stove. If this is likely, secure the appliance to the hearth or floor with suitably strong fixings. FOR MARLBOROUGH, MANHATTAN, STOCKTON & STOCKTON 5: 1.1 Position t ...
-
Yeoman YM-E9001FLA - page 9
9 INSTALLATION INSTRUCTIONS EUROPEAN PLUG - Suitable for use in Austria, Belgium, Bulgaria, Czech Republic, Denmark, Estonia, Finland, France, Greece, Hungary, Germany, Italy, Latvia, Lithu- ania, Luxembourg, Netherlands, Poland, Portugal, Romania, Slovakia, Slovenia, Spain & Sweden Cable grip Outer Insulation Neutral wire Earth wire Live wire ...
-
Yeoman YM-E9001FLA - page 10
10 6 Front LED board Plugs Push fasteners AR2393 1.8 Dispose of the board at an appropriate recycling centre. 1.9 To connect the new LED board push the fasteners through the ready drilled holes and ensure that all wires are correctly connected. REPLACING THE PRINTED CIRCUIT BOARD 1.10 To remove the PCB first remove the front LED board following ins ...
-
Yeoman YM-E9001FLA - page 11
11 REPLACING THE MIDDLE LED BOARD The middle LED board is attached to the motor unit but can be replaced individually (see Diagram 9). 9 AR2395 Rear LED board Middle LED board 1.21 Disconnect the wire connecting the middle LED board to the rear LED board, noting its orientation. 1.22 Attach the new board and reconnect the wire. REPLACING THE REAR L ...
-
Yeoman YM-E9001FLA - page 12
12 1.31 Tilt the heater casing forward and carefully remove the heater assembly (see Diagram 12). 12 AR2398 1.32 Disconnect the 4 x coloured wires running from the firebox to the heater assembly (see Diagram 13) noting their orienta- tion. 13 AR2399 Disconnect wires Disconnect wires 1.33 Fit new heater assembly, ensuring all wires are correctly att ...
-
Yeoman YM-E9001FLA - page 13
13 SPARE PARTS LIST Parts Description Part No. EXMOOR DARTMOOR Fuel Effect PL0116 PL0118 Handset EL0491 Battery EL0492 PCB Unit EL0493 Front LED Board EL0494 Middle LED Board EL0496 Rear LED Board EL0498 Motor & Effect Assembly EL0495 Heater Assembly EL0497 ...
-
Yeoman YM-E9001FLA - page 14
A division of Stovax Ltd Falcon Road, Sowton Industrial Estate, Exeter, Devon, England EX2 7LF Tel: (01392) 474500 Fax: (01392) 219932 E-mail: yeoman@stovax.com www.yeoman-stoves.co.uk ...
Hai una domanda su Yeoman YM-E9001FLA?
Utilizza il modulo sottostante
Se non hai risolto il problema con Yeoman YM-E9001FLA con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Yeoman YM-E9001FLA è probabile che voglia condividere il modo di risolverlo.