Italiano dropdown-ico

Manuale per l’uso Echo CS-680

34 pagine 1.86 mb
Scarica

Vai alla pagina of 34

Summary
  • Echo CS-680 - page 1

    INSTRUCTION MANUAL CHAIN SAW CS-680 WARNING Read the instructions carefully and follow the rules for safe operation. Failure to do so could result in serious injury. X750-012 20 7 X750 316-510 7 ECHO, INCORPORATED 400 Oakwood Road, Lake Zurich, Illinois 60047-1564 Phone : 847-540-8400 Printed in Japan 1312Ek 0798 ES ...

  • Echo CS-680 - page 2

    Copyright © 2008 All Rights Reserved. The engine exhaust fr om this product contains c hemicals known to the State of California to cause cancer , birth defects or other reproductive harm. W ARNING ...

  • Echo CS-680 - page 3

    1 CS-680 RULES FOR SAFE OPERATION A. Kickback Safety Precautions for Chain Saw Users 1. With a basic understanding of kickback, you can reduce or eliminate the element of surprise. Sudden surprise contributes to accidents. 2. Keep a good firm grip on the saw with both hands, the right hand on the rear handle, and the left hand on the front handle, ...

  • Echo CS-680 - page 4

    2 CS-680 1. Do not operate a chain saw with one hand! Serious injury to the operator, helpers, bystanders, or any combination of these persons may result from one- handed operation. A chain saw is intended for two-handed use. 2. Do not operate a chain saw when you are fatigued. 3. Use safety footwear, snug-fitting clothing and protective gloves. W ...

  • Echo CS-680 - page 5

    3 CS-680 WARNING The safety alert symbol accompanied by the word “WARNING” calls attention to an act or condition which CAN lead to serious personal injury or death if not avoided. CAUTION The safety alert symbol accompanied by the word “CAUTION” calls attention to an act or condition which may lead to minor or moderate personal injury if n ...

  • Echo CS-680 - page 6

    4 CS-680 SYMBOL FORM DECALS Locate this safety decal on your unit. The complete unit illustration found in the “NOMENCLATURE OF PARTS” section will help you locate them. Make sure the decal is legible and that you understand and follow the instructions on it. If a decal cannot be read, a new one can be ordered from your ECHO dealer. WARNING!! T ...

  • Echo CS-680 - page 7

    5 CS-680 PACKING LIST The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, guide bar and saw chain installation and other assembly may be necessary. After opening the carton, check for damage. Immediately notify your retailer or ECHO dealer of damaged or missing parts. Use the packing li ...

  • Echo CS-680 - page 8

    6 CS-680 NOMENCLATURE OF PARTS * If a decal cannot be read, a new one can be ordered from your ECHO dealer. 19 14 15 17 16 5 4 8 7 10 11 12 3 2 1 X524-002251 X505-006660 9 21 6 22 20 23 18 13 WARNING!! This chain saw is capable of severe kickback that could result in serious injury to the user. Do not operate this chain saw unless you have extraord ...

  • Echo CS-680 - page 9

    7 CS-680 1. Instruction manual - Included with unit. Read before operation and keep for future reference to learn proper, safe operating techniques. 2. Safety manual - Describe operating and safety instructions for this chain saw. 3. Spiked bumper - Device, fitted in front of the guide bar mounting point, acting as a pivot when in contact with a t ...

  • Echo CS-680 - page 10

    8 CS-680 OPERATOR SAFETY VIBRATION AND COLD s )TISBELIEVEDTHATACONDITIONCALLED2AYNAUDS Phenomenon, which affects the fingers of certain individuals, may be brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning followed by loss of color and numbness in the finge ...

  • Echo CS-680 - page 11

    9 CS-680 SPARK ARRESTOR MUFFLER s 4HESPARKARRESTORMUFmERCONTROLSTHEEXHAUST noise and prevents hot, glowing particles of carbon from leaving the muffler. Make sure the spark arrestor screen is in good repair and properly seated in the muffler. s #ERTAININTERNALCOMBUSTIONENGINESOPERATEDON forest, brush, ...

  • Echo CS-680 - page 12

    10 CS-680 WARNING Saw chain is sharp! Always wear gloves when handling assembly, otherwise serious personal injury may result. GUIDE BAR AND SAW CHAIN INSTALLATION/REMOVAL NOTICE Move the chain brake lever (Front hand guard) fully rearward to remove or install the clutch cover to chain saw. 1. Remove spark plug lead. (See page 25) 2. Remove two clu ...

  • Echo CS-680 - page 13

    11 CS-680 7. T ur n saw o ver and chec k brake band f or correct position on clutch drum. If brake band is not in place around drum, remov e cov er , make sure brak e is unlock ed, and reinstall. Tighten clutch cov er nuts finger tight. WARNING Improper c lutch cover assembl y can result in serious injury , and will cause severe saw damage if unit ...

  • Echo CS-680 - page 14

    12 CS-680 Fuel Mix Chart 50 : 1 U.S. Metric Gasoline Oil Gasoline Oil Gallons US. fl. oz. L mL 1 2.6 4 80 2 5.2 8 160 5 12.8 20 400 FUEL AND LUBRICANT FUEL STATEMENT GASOLINE - Use 89 Octane [(R+M)/2] (mid grade or higher) gasoline or gasohol known to be good quality. Gasohol may contain up to 10 % Ethyl (grain) alcohol or 15 % MTBE (methyl teriar ...

  • Echo CS-680 - page 15

    13 CS-680 HANDLING FUEL MIXING INSTRUCTIONS - 1. Fill an approved fuel container with half of the required amount of gasoline. 2. Add the proper amount of two-stroke oil to gasoline. 3. Close container and shake to mix oil with gasoline. 4. Add remaining gasoline, close fuel container, and remix. IMPORTANT s 3PILLEDFUELISALEADINGC ...

  • Echo CS-680 - page 16

    14 CS-680 WARNING s !FTERCHOKECONTROLKNOBISPULLEDANDTHEN knob is returned to original position, throttle remains a little open (latch condition). s )FENGINEISSTARTEDINTHISLATCHCONDITION chain starts to turn. Do not start engine before chain brake is activated. CAUTION s !FTERSTARTING ...

  • Echo CS-680 - page 17

    15 CS-680 WHEN THE ENGINE IS COLD CAUTION Make sure the bar and chain are free from any obstruction when starting the chain saw. s -OVECHAINBRAKELEVERFULLYFORWARDTOLOCK chain brake before starting. s &ILLTHEFUELTANKWITHFUELMIXTURE It is not permitted to fill fuel above the shoulder level of ...

  • Echo CS-680 - page 18

    16 CS-680 RUNNING s 7HENENGINESTARTSKEEPIDLINGFORAFEW minutes. s 3ETTHEBRAKELEVERINTHEUNLOCKEDPOSITION before starting to cut. s 0ULLTHROTTLETRIGGERGRADUALLYANDINCREASE revolution of the engine. s 4HECHAINSTARTSRUNNINGWHENTHEENGINE reaches 3800 r/m ...

  • Echo CS-680 - page 19

    17 CS-680 CUTTING INSTRUCTION GENERAL CAUTION s 2EADTHE%#(/h#(!).3!73!&%49 MANUAL” included with your chain saw for additional cutting and safety instructions. s 7EARSUITABLEHEARINGPROTECTIONSUCHAS earmuffs or earplugs to protect against objectionable or uncomfortable loud noises. s $ONOTLET? ...

  • Echo CS-680 - page 20

    18 CS-680 FELLING THE TREE A falling tree can seriously damage anything it may hit - a car, a house, a fence, a power-line, or another tree. There are ways to make a tree fall where you want it, so first decide where that is! Before cutting, clear the area around the tree. You will need good footing while working and you should be able to work the ...

  • Echo CS-680 - page 21

    19 CS-680 LIMBING Limbing a fallen tree is much the same as bucking. Never stand on the tree that you are limbing. When limbing, caution is the word. Be careful of the tip touching other limbs. Always use both hands. Don’t cut with the saw overhead or aligned vertically with your body. If the saw should kick- back, you may not have enough control ...

  • Echo CS-680 - page 22

    20 CS-680 Chain brake function When the lever is pushed forward, chain brake instantly stops the chain. Chain brake unlock When the lever is fully pulled toward the operator, brake is unlocked. When the bar nose hits another tree, etc. Improper thrust cutting CHAIN BRAKE OPERATION s 3ETTHELEVERINTHEUNLOCKEDPOSITIONBEFORE ...

  • Echo CS-680 - page 23

    21 CS-680 End of the guide bar may be placed at the height of about 35 cm (14 in.). 35 cm (14 in.) AUTOMATIC CHAIN BRAKE Kickback produced from the tip of the guide bar will trip the automatic chain brake. To make sure that the automatic chain brake operates properly, follow these steps: 1. Stop the engine. 2. Hold the saw with the guide bar approx ...

  • Echo CS-680 - page 24

    22 CS-680 CHAIN AND GUIDE BAR COMBINATION The following combinations are recommended for model CS-680 . GUIDE BAR Replacement guide bars. The following guide bars may be considered to have equivalent kickback energy. s 3PROCKETNOSEGUIDEBARSOFTHESAMELENGTH and nose radius, same pitch and having the same number of teeth. s? ...

  • Echo CS-680 - page 25

    23 CS-680 MAINTENANCE AND CARE IMPORTANT Time intervals shown are maximum. Actual use and your experience will determine the frequency of required maintenance. Your ECHO chain saw is designed to provide many hours of trouble free service. Regular scheduled maintenance will help your chain saw achieve that goal. If you are unsure or are not equipped ...

  • Echo CS-680 - page 26

    24 CS-680 CARBURETOR ADJUSTMENT Every unit is run at the factory and the carburetor is set in compliance with Emission Regulations. In addition, the carburetor is equipped with “H” (High Speed) and “L” (Low Speed) needle adjustment limiters that prevent settings outside acceptable limits. 1. Before adjusting carburetor clean or replace air ...

  • Echo CS-680 - page 27

    25 CS-680 Oil filter Fuel filter Oil tank cap Fuel tank cap 0.65 mm (0.026 in.) Cleaner cover latch Air filter Air cleaner cover AIR FILTER s #HECKBEFOREEVERYUSE s #LOSECHOKE ). s 2ELEASETHECLEANERCOVERLATCHANDREMOVEAIR cleaner cover and filter. s "RUSHOFFDUSTLIGHTLY? ...

  • Echo CS-680 - page 28

    26 CS-680 GUIDE BAR s #LEANBEFOREUSING - Clean the groove of the guide bar with a small screwdriver. - Clean oil holes with a wire. s 2EVERSEGUIDEBARPERIODICALLY s #HECKSPROCKETANDTHECLUTCHANDCLEANTHEBAR mount area before installation of the bar. Replace either or both if worn. SPROCKET ...

  • Echo CS-680 - page 29

    27 CS-680 SETTING THE SAW CHAIN Shar pen lower edge Drive link Tie strap Right hand cutter Preset tie strap Left hand cutter Guard link Top plate Side plate Depth gauge Hold the file tipped 10° upward 10° Important points for proper maintenance of saw chain: s +EEPTHECUTTERSSHARPATALLTIMES s +EEPTHELEFTAND? ...

  • Echo CS-680 - page 30

    28 CS-680 s 0LACETHEDEPTHGAUGETOOLlRMLYONGUIDEBAR so that depth gauge protrudes. Then file top of depth gauge with the flat file until flat with top of the depth gauge tool. - Be sure to round off the front edge of the depth gauge. Properly filed cutters are shown in illustration. When setting of the chain is fin ...

  • Echo CS-680 - page 31

    29 CS-680 TROUBLESHOOTING WARNING Fuel vapors are extremely flammable and MAYCAUSElREANDOREXPLOSION.EVERTEST for ignition spark by grounding spark plug near cylinder plug hole, otherwise serious personal injury may result. Problem Engine — hard to start Cause Remedy — does not start Engine cranks Fuel at carburetor N ...

  • Echo CS-680 - page 32

    30 CS-680 STORAGE AFTER USE * Technical data subject to change without notice. TECHNICAL DATA s )NSPECTANDADJUSTEVERYPARTOFTHECHAINSAW - Completely clean every part and repair if necessary. - Apply thin coating of oil on metal parts to prevent rust. s 2EMOVECHAINANDGUIDEBAR s $RAINFUELT ...

  • Echo CS-680 - page 33

    31 CS-680 WARRANTY STATEMENTS ECHO LIMITED WARRANTY STATEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010 ECHO’S RESPONSIBILITY ECHO Incorporated’s Limited Warranty, provides to the original purchaser that this ECHO product is free from defects in material and workmanship. Under normal use and maintenance from date of purchase, ECHO ...

  • Echo CS-680 - page 34

    32 CS-680 PURCHASED REPAIR PARTS, SHORT BLOCKS AND ACCESSORIES s DAYRESIDENTIALORNONINCOMEPRODUCINGWARRANTY s DAYCOMMERCIALINSTITUTIONALAGRICULTURALINDUSTRIALINCOMEPRODUCINGORRENTALAPPLICATIONWARRANTY ATTENTION TWO-STROKE ENGINE POWER PRODUCT OWNERS This ECHO ...

Fabbricante Echo Categoria Chainsaw

I documenti che otteniamo dal fabbricante del dispositivoEcho CS-680 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Echo
- manuali per l’uso CS-680
- schede prodotto Echo
- opuscoli
- o etichette energetiche Echo CS-680
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Echo CS-680.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Echo CS-680, manuali di manutenzione, brevi manuali o manuali utente Echo CS-680. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Echo CS-680.

Manuali per l’uso simili

Manuale completo del dispositivo Echo CS-680, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Echo CS-680 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Echo CS-680.

Il manuale per l’uso completo Echo, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Echo CS-680 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Echo CS-680, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Echo CS-680 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Echo CS-680 - che ci dovrebbe aiutare nei primi passi durante l'uso Echo CS-680
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Echo CS-680
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Echo CS-680 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Echo CS-680?

Utilizza il modulo sottostante

Se non hai risolto il problema con Echo CS-680 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Echo CS-680 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)