-
RIDGID AC99402 - page 1
1 This Miter Saw Utility V ehicle has been engineered and manufactur ed to our high standard for dependability , ease of operation and op erator safety . When pr operly car ed for , the Miter Saw Utility V ehicle will give you years of rugged, trouble- free performance. WARNING: T o r educe the risk of injury , the user must read and understand the ...
-
RIDGID AC99402 - page 2
2 n Introduction ...................................................................................................................................................................... 2 n Rules for Safe Operation ......................................................................................................................................... ...
-
RIDGID AC99402 - page 3
3 RULES FOR SAFE OPERA TION Safe operation of this accessory r equires that you read and understand this operator's manual, the operator’ s manual for the miter saw and all labels affixed to the tool. READ ALL INSTRUCTIONS n KNOW YOUR ACCESSORY . Read the operator's manual carefully . Lear n the product's applications and limitatio ...
-
RIDGID AC99402 - page 4
4 SYMBOLS The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your car eful attention and understanding. The safety warnings do not by themselves eliminate any danger . The instructions or warnings they give are not substitutes for proper accident pr evention me ...
-
RIDGID AC99402 - page 5
5 UNP ACKING NOTE: Before beginning assembly , check that all parts ar e included. If you ar e missing any part, do not assemble this accessory . Call 1-800-4-RIDGID or E-mail us at info@rid gidwoodworking.com to get the missing part. Sometimes n Stand Assembly (1) n Roller Assembly (2) n Wheels (2) n Operator's Manual (1) n Hex Bolt, M8x50 mm ...
-
RIDGID AC99402 - page 6
6 ASSEMBL Y A TT ACHING THE LOWER FOOT See Figures 1 d 2. n Place stand assembly “flat” on floor . n Rotate lower foot into upright position aligning holes as shown. n Locate the following parts: Hex Bolt, M8 x 50 mm (2) Flat W asher , M8 (4) Lock Nut, M8 (2) n Install bolt, two washers and lock nut as shown. Finger tighten lock nut. n Repeat a ...
-
RIDGID AC99402 - page 7
7 WORKST AND SET -UP See Figures 4 - 5. Before Y ou Start n If a miter saw is already assembled to the stand, make sure that it is securely attached to the stand per the instructions in this manual. n If a compound miter saw is already assembled to the stand, make sure to place the blade 90° to the table (if applicable). Miter the blade to the rig ...
-
RIDGID AC99402 - page 8
8 ASSEMBL Y MOUNTING MITER SA W See Figures 6 - 7. WARNING: Failure to unplug the tool could r esult in accidental starting causing possible serious personal injury . Before Y ou Start RIDGID miter saws bolt directly onto this workstand. When you ar e finished attaching your saw to the workstand rer ead the Operation and Rules for Safe Operation se ...
-
RIDGID AC99402 - page 9
9 ASSEMBL Y MOUNTING OTHER BRANDS See Figure 8. NOTE: Other brands of miter saws (not RIDGID miter saws) will requir e additional 5/16 in. mounting holes to be drilled. See instructions below . n Locate the following parts: Hex Bolts, M6 x 40mm (4) Flat W ashers, M6 (4) Fender W ashers, M6 (4) Lock Nuts, M6 (4) CENTER THE MITER SA W ON THE WORK- ST ...
-
RIDGID AC99402 - page 10
10 ASSEMBL Y EXTENSION BAR(S) OPERA TION See Figures 10 - 11. Both extension bars may be adjusted to pr ovide maximum workpiece support. T o adjust the extension bars: n Loosen adjustable handle by tur ning counter clock- wise. NOTE: Adjustable handle can be repositioned if necessary . Lift up on handle and rotate to desired position then release h ...
-
RIDGID AC99402 - page 11
11 Before Y ou Start n Remove any workpieces, clamps or other accessories. n Make sure miter saw is securely attached to the stand per the instructions in this manual. n If a miter saw is already assembled to the stand, make sure to place the blade 90° to the table (if applicable), miter the blade to the right as far as it will go, place the blade ...
-
RIDGID AC99402 - page 12
12 ASSEMBL Y TRANSPORTING TOOL See Figure 15. n When hauling the workstand in a vehicle, securely tie it down to prevent movement and possible damage. n Always get help if you need to lift the workstand. When lifting, hold the workstand close to your body . Bend your knees so you can lift with your legs, not your back. MAINTENANCE See Figures 16 - ...
-
RIDGID AC99402 - page 13
13 EXPLODED VIEW/REP AIR P AR TS Miter Saw Utility V ehicle Model AC99401 RIDGID parts are at www .ridgidparts.com 1 829859 Rear Roller Extension 2 829758-5 W asher (20 x 10.5 x 1.5) 3 829759-3 Nylock Nut (M10) 4 829799 Rubber Cap 5 829757-6 Hex Head Bolt (M8 x 1.25 x 33) 6 830256 T able 7 829871-1 Compression Spring 8 829741 Clamp 9 829758-5 W ash ...
-
RIDGID AC99402 - page 14
14 NOTES ...
-
RIDGID AC99402 - page 15
15 W ARRANTY Proof of purchase must be presented when r equesting war - ranty service. Limited to RIDGID ® hand held and stationary power tools purchased 2/1/04 and after . This product is manufactured by One W orld T echnologies, Inc. The trademark is licensed from RIDGID, Inc. All warranty communications should be dir ected to One W orld T ech n ...
-
RIDGID AC99402 - page 16
16 Customer Service Information: For parts or service, contact your nearest RIDGID authorized service center . Be sure to provide all relevant information when you call or visit. For the location of the authorized service center near est you, please call 1-866-539-1710 or visit us online at www .ridgid.com. The model number and serial number are fo ...
Hai una domanda su RIDGID AC99402?
Utilizza il modulo sottostante
Se non hai risolto il problema con RIDGID AC99402 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con RIDGID AC99402 è probabile che voglia condividere il modo di risolverlo.