Italiano dropdown-ico

Manuale per l’uso MTD E610E

28 pagine 4.42 mb
Scarica

Vai alla pagina of 28

Summary
  • MTD E610E - page 1

    IMPOR T ANT : READ SAFETY R ULES AND INSTR UCTIONS CAREFULL Y MTD PR ODUCTS INC. P .O . BO X 368022 CLEVELAND , OHIO 44136-9722 SNO W THR O WERS Models E600E, E610E E640F , E660G Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest- covered, brush-covered or grass-covered land unl ...

  • MTD E610E - page 2

    2 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE YOUR SNOW THROWER. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY ...

  • MTD E610E - page 3

    3 • If the snow thrower should start to vibrate abnormally, stop the engine and check immediately for the cause. Vibration is generally a warning of trouble. • Stop engine whenever you leave the operating position, before unclogging the collector/impeller housing or discharge guide, and making any repairs, adjustments, or inspections. Never pla ...

  • MTD E610E - page 4

    4 SECTION 2: FINDING YOUR MODEL NUMBER This Operator’s Manual is an important part of your new snow thrower. It will help you assemble, prepare and maintain your snow thrower. Please read and understand what it says. Before you start to prepare your snow thrower for its first use, please locate the model plate and copy the information from it in ...

  • MTD E610E - page 5

    5 SECTION 4: CONTENTS OF HARDWARE PACK La y out the hardware according to the illustration f or identification pur poses. Part numbers are shown in parentheses. (Hardware pac k may contain e xtra items which are not used on y our unit.) A ATTACHING THE HANDLES Hex Bolts (A) (710-3180) Handle T abs (784-5599) Hex Bolts (710-3008) Lock Washers (736- ...

  • MTD E610E - page 6

    6 SECTION 5: ASSEMBLY INSTRUCTIONS IMPORTANT: After assembly, service engine with gasoline, and check oil level as instructed in the separate engine manual packed with your unit. NOTE: All references to right or left side of the snow thrower are determined from behind the unit in the operating position. UNP A CKING • Remove staples or break glue ...

  • MTD E610E - page 7

    7 Figure 4 Figure 5 Figure 6 A TT A CHING THE HANDLE ASSEMBL Y (Hard ware A) 1. Place right handle (A) in position against the snow thro wer so the flat side of the handle is against the snow thro wer . Secure bottom hole in handle to snow thro wer using he x bolt 3/4" long and lock w asher . See Figure 4. Do not tighten at this time. 2. Plac ...

  • MTD E610E - page 8

    8 Figure 7 Figure 8 Figure 9 Figure 10 A TT A CHING THE CHUTE ASSEMBL Y (Hard ware B) Place chute assembly (C) o ver chute opening, with the opening in the chute assembly f acing the front of the unit. Place chute flange keepers beneath lip of chute assembly , with the flat side down. Secure with he x head screws and he x lock n uts as shown in F ...

  • MTD E610E - page 9

    9 Figure 11 Figure 12 IMPORT ANT : Attach the shift rod and clutch cables as f ollows . THEN CHECK THE ADJUSTMENTS AS INSTR UCTED , AND MAKE ANY FINAL ADJUST - MENTS NECESSAR Y BEFORE OPERA TING Y OUR SNO W THRO WER. F ailure to follo w the instr uctions ma y cause damage to the snow thro wer . A TT A CHING THE SHIFT ROD (Har d ware D) 1. Place the ...

  • MTD E610E - page 10

    10 T raction Drive Clutch and Shift Le ver Adjustment To check the adjustment of the traction drive clutch and shift lever, move the shift lever all the way forward to sixth (6) position. With the traction drive lever released, push the snow thrower forward. The unit should move forward freely. Then engage the traction drive clutch grip. The wheels ...

  • MTD E610E - page 11

    11 TRA CTION DRIVE/A UGER CLUTCH LOCK (See Figure 14) The traction drive clutch is located on the right handle. Squeeze the traction driv e clutch to engage the wheel drive . Release to stop . This same le v er also locks the auger clutch so y ou can tur n the chute crank without interr upting the snow throwing process . If the auger drive clutch i ...

  • MTD E610E - page 12

    12 Electric Starter: WARNING: The electric starter is equipped with a three-wire power cord and plug, and is designed to operate on 120 volt AC household current. It must be properly grounded at all times to avoid the possibility of electric shock which may be injurious to the operator. Follow all instructions carefully. Determine that your house w ...

  • MTD E610E - page 13

    13 5. Wipe all snow and moisture from the carburetor cover in the area of the control levers. Also, move control levers back and forth several times. T O ENGA GE DRIVE 1. With the engine running near top speed, move shift lever into one of the five FORWARD positions or two REVERSE positions. Select a speed appropriate for the snow conditions that e ...

  • MTD E610E - page 14

    14 SKID SHOE ADJUSTMENT The space between the sha v e plate and the ground can be adjusted. Ref er to page 10 of the Assembly Instructions. TRA CTION DRIVE CLUTCH ADJUSTMENT Ref er to the Final Adjustment section of the Assem- bly Instructions to adjust the traction drive clutch. If you are uncertain that you hav e reached the correct adjustment, t ...

  • MTD E610E - page 15

    15 WHEELS Oil or spray lubricant into bearings at wheels at least once a season. Pull the klick pins and remove wheels, clean and coat axles with a multipurpose automotive grease. See Figure 23. Figure 23 . Figure 24 A UGER SHAFT Remove shear bolts on auger shaft. Oil or spray lubricant inside shaft. See Figure 24. GEAR SHAFT Lubricate the gear sha ...

  • MTD E610E - page 16

    16 BEL T REMO V AL AND REPLA CEMENT WARNING: Disconnect the spark plug wire from the spark plug and ground. A UGER BEL TS NOTE: It is necessary to remove both belts in order to change either one. If changing just one belt, be certain to check the condition of the other belt (model 600/610E has only one auger belt) . 1. Remov e the plastic belt cove ...

  • MTD E610E - page 17

    17 Figure 28 CHANGING FRICTION WHEEL R UBBER The rubber on the friction wheel is subject to wear and should be check ed after 25 hours of operation, and periodically thereafter . Replace the fr iction wheel rubber if any signs of wear or cr acking are f ound. 1. Drain the gasoline from the sno w thro wer , or place a piece of plastic under the gas ...

  • MTD E610E - page 18

    18 SECTION 12: Trouble Shooting Guide Note: For repairs beyond the minor adjustments above, contact your local authorized service dealer. T rouble P ossible Cause(s) Corrective Action Engine f ails to star t Fuel tank empty , or stale fuel. Block ed fuel line. Choke not in ON position F aulty spark plug. K ey not in s witch on engine. Spark plug wi ...

  • MTD E610E - page 19

    19 REF . NO . PA R T NO . DESCRIPTION Qty . 1 618-0123 Housing—L.H. 1 2 618-0124 Housing—R.H. 1 3 710-0642 Screw 5 4 711-0908 Spiral Axle 24" 1 711-0909 Spiral Axle 26" 1 711-0910 Spiral Axle 28" 1 5 714-0161 K ey 1 6 715-0143 Pin-Spiral 1 7 717-0526 Shaft-W orm 1 8 717-0528 Gear-W orm 1 9 718-0186 Collar-Thrust 1 10 721-0325 Plu ...

  • MTD E610E - page 20

    20 Blower Housing E600E E610E E640F E660G ...

  • MTD E610E - page 21

    21 Blower Housing E600E E610E E640F E660G REF . NO . PA R T NO . DESCRIPTION QTY . 1 784-5618 Housing, Bearing 2 2 05931 Housing, Bearing 1 3 618-0120 Gear Assembly (24") 1 618-0121 Gear Assembly (26") 1 618-0122 Gear Assembly (28") 1 4 684-0039A 24" Housing Assembly 1 684-0040A 26" Housing Assembly 1 684-0041A 28" Hou ...

  • MTD E610E - page 22

    22 Handle Assembly E600E E610E E640F E660G ...

  • MTD E610E - page 23

    23 Handle Assembly E600E E610E E640F E660G REF . NO . PA R T NO . DESCRIPTION QTY . 1 684-0008A Arm-Shift 1 3 684-0033A P anel-Handle 1 4 684-0036 Handle-Engagement—R.H. 1 5 684-0037 Handle-Engagement—L.H. 1 7 710-0276 Scre w 1 8 710-0451 Bolt-Carriage 1 9 710-0599 Scre w 4 10 710-1003 Screw 2 11 711-0653 Pin-Cle vis 1 12 712-0116 Nut-He x 1 13 ...

  • MTD E610E - page 24

    24 Frame Assembly E600E E610E E640F E660G ...

  • MTD E610E - page 25

    25 Frame Assembly E600E E610E E640F E660G REF . NO . PA R T NO . DESCRIPTION QTY . 1 618-0063 Bearing Ass’y . 1 2 656-0012A Ass’y ., F r iction Wheel Disc 1 3 684-0013B Rod Shift, Wheel Dr ive 1 4 684-0021 Brkt. Ass’y . Friction Wheel 1 5 684-0030 F rame Ass’y ., 600 S/T 1 6 684-0042B Wheel F r iction 1 7 710-0654A He x Self-T ap Screw 4 8 ...

  • MTD E610E - page 26

    26 REF . NO . PA R T NO . DESCRIPTION QTY . 1 05896A Brac ket-Idler 1 2 629-0071 Cord-Extension 110V 1 3 710-0627 Screw-He x 1 4 710-1245 Screw-He x 1 5 710-0230 Screw-He x 1 6 710-0342 Screw-He x 1 7 710-0696 Screw-He x 1 8 710-0627 Screw-He x 1 9 710-0896 Screw-He x 2 10 712-0181 Nut-Hex 1 11 731-1324 Cover-Belt 1 12 732-0339 Spr ing 1 13 736-011 ...

  • MTD E610E - page 27

    27 Engine and V-Belts E640F E660G 16 736-0270 W asher—Lock 1 17 736-0331 W asher—Bell 1 18 736-0505 W asher—Flat 1 19 748-0234 Shoulder Spacer 1 20 748-0360 Pulle y , Adapter 1 21 754-0346 V -Belt 1 22 754-0430 V -Belt Matched 2 23 756-0313 Idler , Flat 1 24 756-0569 Pulle y , Half 4 25 756-0967 Pulle y—Auger 2 26 756-0986 Pulle y Half 1 27 ...

  • MTD E610E - page 28

    MANUF A CTURER’S LIMITED W ARRANTY FOR: For TWO YEARS from the date of retail purchase within the United States of America, its possessions and territories, MTD PRODUCTS INC will, at its option, repair or replace, for the original purchaser, free of charge, any part or parts found to be defective in material or workmanship. This warranty covers u ...

Fabbricante MTD Categoria Snow Blower

I documenti che otteniamo dal fabbricante del dispositivoMTD E610E possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici MTD
- manuali per l’uso E610E
- schede prodotto MTD
- opuscoli
- o etichette energetiche MTD E610E
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso MTD E610E.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione MTD E610E, manuali di manutenzione, brevi manuali o manuali utente MTD E610E. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto MTD E610E.

Manuali per l’uso simili

Manuale completo del dispositivo MTD E610E, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare MTD E610E dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti MTD E610E.

Il manuale per l’uso completo MTD, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale MTD E610E - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice MTD E610E, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per MTD E610E che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo MTD E610E - che ci dovrebbe aiutare nei primi passi durante l'uso MTD E610E
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del MTD E610E
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio MTD E610E in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su MTD E610E?

Utilizza il modulo sottostante

Se non hai risolto il problema con MTD E610E con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con MTD E610E è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)