Manuale per l’uso Pelco IV SE SERIES

16 pagine 0.88 mb
Scarica

Vai alla pagina of 16

Summary
  • Pelco IV SE SERIES - page 1

    INSTALLATION Spectra ® IV Series Spectra ® IV SE Series C3416M-B (11/06) Surface Mount Back Box ...

  • Pelco IV SE SERIES - page 2

    2 C3416M-B (11/06) Installation 1 2 3 ...

  • Pelco IV SE SERIES - page 3

    C3416M-B (11/06) 3 1. Using the ba ck box as a t emplate, mark the fasten er positions on the moun ting surfac e. 2. Prepare th e mounting surfa ce. Pull power and video wire/cab le for the do me system. Refer to T able A, T able B, and T able C f or wiring distances . 3. Open the hi nged door t o the back b ox. Push t he tab lock towards the wall ...

  • Pelco IV SE SERIES - page 4

    4 C3416M-B (11/06) 4 5 VIDEO UTP+ UTP- RX- RX+ TX+ TX- PWR- PWR+ GND AUX2 GND GND NO NC COM 7 6 5 4 3 2 1 ALARMS AUX1 ...

  • Pelco IV SE SERIES - page 5

    C3416M-B (11/06) 5 4. Attach the back box to the moun ting surfa ce. 5. Connect wir ing to the circuit boa rd inside the back box. When finished, clos e the door to th e back box and turn on t he power . The green LED will light . NOTES: • Aux 1: Maximum 2 A at low voltage (<40 V) Aux 2: Maximum 30 mA at 32 VDC • If you are u sing both u nsh ...

  • Pelco IV SE SERIES - page 6

    6 C3416M-B (11/06) SWITCH 1 AND 2 6 7 8 9 ...

  • Pelco IV SE SERIES - page 7

    C3416M-B (11/06) 7 6. Attach the b ack box leash to the lower dome by sliding the leash through the tab o f the lower dome until it snap s into place. 7. Configure DI P switches SW1 and SW2 locate d on the top of the dome drive. For DIP switch settings, refer to the labels locat ed on the top of the dome dr ive or to t he Switch Settings section. N ...

  • Pelco IV SE SERIES - page 8

    8 C3416M-B (11/06) T roubleshooting If your dome do es not power up proper ly after installati on, use the following steps. 1. Check the fuse on the circuit boa rd inside the ba ck box for continuity . Replace the fuse if needed. 2. Check the wiri ng with a volt meter to en sure pr oper voltage is being received into the ba ck box. If your dome pow ...

  • Pelco IV SE SERIES - page 9

    C3416M-B (11/06) 9 Switch Settings WAR N I NG : If you are using D-ty pe or P-type control, your system may no t operate if the baud rate and address switches are not set cor rectly . The switches ar e set at t he factory at the def aults for D-t ype control (2400 baud and address 1). T able E. Switch Settings for SW2 Special Sy stems S w i t c h N ...

  • Pelco IV SE SERIES - page 10

    10 C3416M-B (11/06) T able F . Switch Settings for SW1, P- T ype Control NOTE: For Coaxitron controls, SW1 is not us ed; set all switches OFF . For D-type con trol systems, refer to T able G . T able G. Switch Settings for SW1, D-T ype Control NOTE: For Coaxitron controls, SW1 is not used; set all switches OFF . For P-type con trol systems, refer t ...

  • Pelco IV SE SERIES - page 11

    C3416M-B (11/06) 11 SPECTRA ADDRESS SWITCH SETTI NG SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 71 ON ON ON OFF OFF OFF ON OFF 72 OFF OFF OFF ON OFF OFF ON OFF 73 ON OFF OFF ON OFF OFF ON OFF 74 OFF ON OFF ON OFF OFF ON OFF 75 ON ON OFF ON OFF OFF ON OFF 76 OFF OFF ON ON OFF OFF ON OFF 77 ON OFF ON ON OFF OFF ON OFF 78 OFF ON ON ON OFF OFF ON O ...

  • Pelco IV SE SERIES - page 12

    12 C3416M-B (11/06) SPECTRA ADDRESS SWITCH SET TING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 151 ON ON ON OFF ON OFF OFF ON 152 OFF OFF OFF ON ON OFF OFF ON 1 5 3 O NO F F O F FO N O NO F F O F FO N 154 OFF ON OFF ON ON OFF OFF ON 155 ON ON OFF ON O N OFF OFF ON 156 OFF OFF ON ON ON OFF OFF ON 157 ON OFF ON ON ON OFF OFF ON 158 OFF ON ON ON ...

  • Pelco IV SE SERIES - page 13

    C3416M-B (11/06) 13 SPECTRA ADDRESS SWITCH SETTI NG SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 223 ON ON ON ON ON OFF ON ON 224 OFF OFF OFF OFF OFF ON ON ON 225 ON OFF OFF OFF OFF ON ON ON 226 OFF ON OFF OFF OFF ON ON ON 227 ON ON OFF OFF OFF ON ON ON 228 OFF OFF ON OFF OFF ON ON ON 229 ON OFF ON OFF OFF ON ON ON 230 OFF ON ON OFF OFF ON ON ON ...

  • Pelco IV SE SERIES - page 14

    14 C3416M-B (11/06) Specifications *For variable- speed operatio n an appropriat e controller is re quired. With fixed-s peed controll ers, pan/tilt speed is 20°/sec. The CM6700/CM68 00 controller with the KBD200A keyboard has pro grammable fixed speeds. The materials used in the manufacture of this document and its co mponents are compliant to th ...

  • Pelco IV SE SERIES - page 15

    PRODUCT WARRANTY AND RETURN INFORMA TION WARRA NTY Pelco will r epair or repla ce, without char ge, any merc handise proved d efective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are a s noted below: • Five years on FR/F T/FS Series fiber optic produc ts and TW3000 Series unshielded ...

  • Pelco IV SE SERIES - page 16

    W orldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .p elco.c om ISO 9001 Australia | Canada | Finland | France | Italy | Russia | Singapore | Spain | Sweden | The Netherl ands | United Ar ab Emirat es | United Kingdom | ...

Fabbricante Pelco Categoria Home Security System

I documenti che otteniamo dal fabbricante del dispositivoPelco IV SE SERIES possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Pelco
- manuali per l’uso IV SE SERIES
- schede prodotto Pelco
- opuscoli
- o etichette energetiche Pelco IV SE SERIES
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Pelco IV SE SERIES.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Pelco IV SE SERIES, manuali di manutenzione, brevi manuali o manuali utente Pelco IV SE SERIES. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Pelco IV SE SERIES.

Manuali per l’uso simili

Manuale completo del dispositivo Pelco IV SE SERIES, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Pelco IV SE SERIES dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Pelco IV SE SERIES.

Il manuale per l’uso completo Pelco, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Pelco IV SE SERIES - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Pelco IV SE SERIES, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Pelco IV SE SERIES che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Pelco IV SE SERIES - che ci dovrebbe aiutare nei primi passi durante l'uso Pelco IV SE SERIES
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Pelco IV SE SERIES
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Pelco IV SE SERIES in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Pelco IV SE SERIES?

Utilizza il modulo sottostante

Se non hai risolto il problema con Pelco IV SE SERIES con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Pelco IV SE SERIES è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Commenti (0)