Italiano dropdown-ico

Manuale per l’uso Delta BS150LS

25 pagine 0.95 mb
Scarica

Vai alla pagina of 25

Summary
  • Delta BS150LS - page 1

    INSTRUCTION MANUAL 10" Band Saw (Model BS150LS) P ART NO. A03617 - 03-17-04 Copyright © 2004 Delta Machinery ESP AÑOL: PÁGINA 25 T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). ...

  • Delta BS150LS - page 2

    2 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury . Used without the saf ...

  • Delta BS150LS - page 3

    3 GENERAL SAFETY RULES 1. FOR YOUR OWN SAFETY , READ THE INSTRUCTION MANUAL BEFORE OPERA TING THE MACHINE. Learning the machine’ s application, limitations, and specific hazards will gr eatly minimize the possibility of accidents and injury . 2. WEAR EYE PROTECTION. AL WA YS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is d ...

  • Delta BS150LS - page 4

    4 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cor ds which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug. Before connec ...

  • Delta BS150LS - page 5

    5 Fig. A Fig. B GROUNDED OUTLET BOX CURRENT CARR YING PRONGS GROUNDING BLADE IS LONGEST OF THE 3 BLADES GROUNDED OUTLET BOX GROUNDING MEANS ADAPTER Repair or replace damaged or worn cord immediately . 2. Grounded, cor d-connected machines intended for use on a supply circuit having a nominal rating less than 150 volts: If the machine is intended fo ...

  • Delta BS150LS - page 6

    6 FUNCTIONAL DESCRIPTION FOREWORD The Delta ShopMaster Model BS150LS 10" Band Saw has a powerful 1/2 HP , ball-bearing motor for smooth performance and long life. The saw has a 7 inch depth of cut capacity . The BS150LS is supplied with a cast iron table and sturdy steel stand which pr ovides heavy-duty support and a comfortable work height. N ...

  • Delta BS150LS - page 7

    7 BAND SA W ASSEMBL Y P AR TS FOR YOUR OWN SAFETY , DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETEL Y ASSEMBLED AND YOU READ AND UNDERST AND THE ENTIRE INSTRUCTION MANUAL. 1. Band Saw 2. 5mm Hex Wr ench 3. 4mm Hex Wr ench 4. 3mm Hex Wr ench 5. M8 x 45mm Hex Head Screw (4) 6. 3/8" Flat W asher (8) 7. M8 Lock W ashe ...

  • Delta BS150LS - page 8

    8 ASSEMBL Y FOR YOUR OWN SAFETY , DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETEL Y ASSEMBLED AND YOU READ AND UNDERST AND THE ENTIRE INSTRUCTION MANUAL. ST AND ASSEMBL Y 1. Assemble stand as shown in Fig. 4, using parts shown in Fig. 3. The brackets and legs are identified with the same letter in both illustrations. I ...

  • Delta BS150LS - page 9

    9 3. Place a 3/8" flat washer (H) Fig. 7 on M8 x 45mm hex head screw . Insert the screw through the hole in the band saw and and through the hole in the stand. Repeat this process for the thr ee remaining holes. Fig. 7 D Fig. 8 4. Place a 3/8" flat washer on the screw (D) Fig. 8, followed by M8 lock washer , then thread a M8 hex nut on sc ...

  • Delta BS150LS - page 10

    10 Fig.14 Fig.15 7. Fig. 14 shows the disassembled table tilt pinion knob (N) , spring (O), and special screw (P), removed in STEP 1 . 8. Re-assemble the table tilt pinion knob (N) Fig. 15, on the back of saw so that the teeth on the pinion knob (N) engage the teeth on the trunnion (R). Fasten in place with the special scr ew ( P) and spring using ...

  • Delta BS150LS - page 11

    11 Fig.16 9. Loosen the screw (T) Fig. 16 and align pointer (S) with "0" mark on the trunnion scale (M). Tighten securely . NOTE: Make sure table is set at 90 degr ees to the blade or check the pointer alignment after adjusting the table stops (see section" ADJUSTING THE T ABLE POSITIVE STOPS"). 10 . Re-assemble the scr ew (W) F ...

  • Delta BS150LS - page 12

    12 12 OPERA TING CONTROLS AND ADJUSTMENTS Fig. 21 Fig. 22 Fig. 23 ST ARTING AND STOPPING SA W The "ON/OFF" switch is located on the fr ont side of the band saw . T o turn the saw "ON", push the button (A) Fig. 21 in to the "ON" position. T o tur n the saw "OFF", push the button (B) Fig. 22 in to the "OFF ...

  • Delta BS150LS - page 13

    13 Fig. 24 ADJUSTING BLADE TENSION Blades of 1/8", 1/4", and 3/8" in width by 59-1/2" in length are available for use with your band saw . NOTE: The blade tension must be adjusted to accommodate differ ent blade widths in order to pr ovide proper blade tracking, cutting performance, and blade life. DISCONNECT MACHINE FROM POWER ...

  • Delta BS150LS - page 14

    14 14 ADJUSTING UPPER BLADE GUIDES AND BLADE SUPPOR T BEARING IMPORT ANT : BOTH THE UPPER AND LOWER BLADE GUIDES MUST BE PROPERL Y ADJUSTED TO PREVENT THE BLADE FROM TWISTING DURING OPERA TION . DISCONNECT MACHINE FROM POWER SOURCE . UPPER BLADE GUARD (B) FIG. 27 IS SHOWN REMOVED FOR CLARITY . AL W A YS MAKE SURE THE UPPER BLADE GUARD IS INST ALLED ...

  • Delta BS150LS - page 15

    15 ADJUSTING LOWER BLADE GUIDES AND BLADE SUPPORT BEARING The lower blade guides and blade support bearing should be adjusted at the same time as the upper guides and support bearings as follows: DISCONNECT MACHINE FROM POWER SOURCE. 1. Loosen two screws (A) Fig. 29, and move guides (B) as close as possible to the sides of the blade. Be careful not ...

  • Delta BS150LS - page 16

    16 16 ADJUSTING THE T ABLE POSITIVE STOPS Positive stops are pr ovided for the table at the 90 and 45 degree angle to the blade. T o check and adjust the positive stops: DISCONNECT MACHINE FROM POWER SOURCE. 1. Tilt the table to the 90 degree position as shown in Fig. 32 and tighten lock handle (A). Place a square (H) on the table and against the b ...

  • Delta BS150LS - page 17

    17 CHANGING BLADES T o change blades: DISCONNECT MACHINE FROM POWER SOURCE. 1. Pull door latches (A) Fig. 35 and open doors (B). 2. Loosen the two screws (C) Fig. 36, and remove the blade guard (D). 3. T o release tension on the band saw blade loosen screw (E) and turning tension knob (G) Fig. 35 counterclockwise. 4. Remove table alignment screw (F ...

  • Delta BS150LS - page 18

    18 18 Before starting the machine, see that all adjustments ar e properly made and the guar ds are in place. T ur n the upper wheel by hand to make sure that everything is corr ect BEFORE turning on the power . Keep the top guide within 1/8" of the work piece at all times. Do not force the material against the blade. Light pr essure on the wor ...

  • Delta BS150LS - page 19

    19 Fig. 41 Fig. 41 illustrates a typical bevel cutting operation using the accessory miter gage. Fig. 42 Fig. 42 illustrates a typical resawing application using the accessory rip fence. ...

  • Delta BS150LS - page 20

    20 In spite of how well a band saw is maintained, problems can occur . The following troubleshooting guide will help you solve the more common pr oblems: (continued on next page) T rouble: SAW WILL NOT ST ART . Probable Cause Remedy 1. Saw not plugged in. 1. Plug in saw . 2. Fuse blown or circuit breaker tripped. 2. Replace fuse or reset circuit br ...

  • Delta BS150LS - page 21

    21 T rouble: BLADE WILL NOT TRACK. Pr obable Cause Remedy 1. Blade too loose 1. Adjust tension 2. Upper wheel not properly adjusted. 2. Adjust upper wheel. 3. Improperly adjusted blade support bearing. 3. Adjust blade support bearing. T rouble: CUT DOES NOT AGREE WITH SETTING ON THE TIL T SCALE. Pr obable Cause Remedy 1. Pointer out of adjustment 1 ...

  • Delta BS150LS - page 22

    22 BAND SA W BLADES A band saw blade is a delicate piece of steel that is subjected to tremendous strain. Y ou can obtain long use fr om a band saw blade if you use it properly . Use blades of proper thickness, width and temper for the various types of material and cuts. Always use the widest blade possible. Use narrow blades only for sawing small, ...

  • Delta BS150LS - page 23

    23 NOTES ...

  • Delta BS150LS - page 24

    24 24 24 P ARTS, SERVICE OR W ARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standards and ar e serviced by a network of Porter -Cable • Delta Factory Service Centers and Delta Authorized Service Stations. T o obtain additional information regar ding your Delta quality product or to obtain parts, service, ...

  • Delta BS150LS - page 25

    The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas r egistradas de PORTER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T ...

Fabbricante Delta Categoria Saw

I documenti che otteniamo dal fabbricante del dispositivoDelta BS150LS possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Delta
- manuali per l’uso BS150LS
- schede prodotto Delta
- opuscoli
- o etichette energetiche Delta BS150LS
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Delta BS150LS.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Delta BS150LS, manuali di manutenzione, brevi manuali o manuali utente Delta BS150LS. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Delta BS150LS.

Manuali per l’uso simili

Manuale completo del dispositivo Delta BS150LS, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Delta BS150LS dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Delta BS150LS.

Il manuale per l’uso completo Delta, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Delta BS150LS - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Delta BS150LS, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Delta BS150LS che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Delta BS150LS - che ci dovrebbe aiutare nei primi passi durante l'uso Delta BS150LS
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Delta BS150LS
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Delta BS150LS in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Delta BS150LS?

Utilizza il modulo sottostante

Se non hai risolto il problema con Delta BS150LS con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Delta BS150LS è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)