Italiano dropdown-ico

Manuale per l’uso KVH Industries TracVisionM7

31 pagine 2.26 mb
Scarica

Vai alla pagina of 31

Summary
  • KVH Industries TracVisionM7 - page 1

    T racVision M7 Installation Guide T racVision M7 Switchplate Configuration ...

  • KVH Industries TracVisionM7 - page 2

    T racVision M7 Installation Guide 1 Switchplate Configuration KVH, TracVision, and the unique light-colored dome with contrast ing baseplate are registered trademarks of KVH Industries, Inc. All other trademarks are property of their r espective companies. The information in this document is subject to change w ithout notice. No company shall be li ...

  • KVH Industries TracVisionM7 - page 3

    3 Before you begin, follow these steps to make sure you have everything you need to complete the installation. a. Unpack the bo x and ensure it contains everything shown on the Kitpack Conte nts List . Save the packagin g for future use. b. Carefully examine all of the supplied parts to ensure nothing was damag ed in shipment. c. Gather all of the ...

  • KVH Industries TracVisionM7 - page 4

    4 Before you begin, consid er the following antenna installation guidelines: • Minimize blockage. The antenna requires a clear view of the sky to receive satellite TV (see Figure 4). The fewer obstructions, the better the system will perform. • Make sure the mounting surface is w ide enough to accommodate th e antenna’s base (see Figure 5). A ...

  • KVH Industries TracVisionM7 - page 5

    5 Before you begin, consider the following switchplate installa tion guidel ines: • Select a switchplate mounting location in a dry, well-ventilated area belowdecks away from any heat sources or salt spray. • Be sure to leave enough room at the switchplate’s rear panel for connect ing the cables (see Figure 6 for switchplate dimensions). • ...

  • KVH Industries TracVisionM7 - page 6

    6 Once you have ident ified a suitable an tenna mounting site, accordin g to the guidelines provided in Step 2, follow these steps to drill the mounting holes and ca ble access hole to prepare the site for installation. a. Unfold the antenna mounting template (supplied in the Custom er Welcome Kit) an d place it onto the mounting surfac e. Make sur ...

  • KVH Industries TracVisionM7 - page 7

    7 Inside the antenna, a foam block prevents the antenna assembly from moving during shipment. Follow these steps to remove thi s shipping restraint. a. Remove the six #10-32 Phillips screws securing the radome to the baseplat e (see Figure 10). Carefully lif t the radome straight up until clear of the antenna assembly and set it aside in a safe pla ...

  • KVH Industries TracVisionM7 - page 8

    8 Follow these steps to connect the data, power, and RF cables to the antenna. a. First determine the number of RF coa x cables required for your partic ular installation (see Figure 12). (See Figure 13 to determine t he type of cable required.) b. Route the data, power, and RF cables belowdecks through the 3" (80 mm) cable access hole. Leave ...

  • KVH Industries TracVisionM7 - page 9

    9 Follow these steps to mount the antenna to the mounting surface. a. Place the antenn a baseplate over the holes drilled in the mounting surface. b. Make sure the forward arrow inside the baseplate points toward the bow and is parallel to the vess el’s centerline (see Figure 15). c. Ma ke su r e t he fo ur h ol e s in the baseplate line up with ...

  • KVH Industries TracVisionM7 - page 10

    10 Follow these steps to connect the switchplate to the ante nna. NOTE: System wiring diagrams are provided in Appendix D on page 27. a. First dress the data an d power cables from the antenna . Strip back the ins ulation of each wire approximately 1/4" (6 mm ) and gently twist each wi re to ensure a good electr ical connection. b. Connect the ...

  • KVH Industries TracVisionM7 - page 11

    11 In Step 6, you routed the RF coax cable (s) from the antenna, through the cable access hole, and into the vessel. Follow these steps to connect the RF coax cable(s) to the customer’s satellite TV receiver(s). a. If you are connecting two rece ivers to the TracVision system, decide which receiver will be the primary receiver. The primary receiv ...

  • KVH Industries TracVisionM7 - page 12

    12 Follow these steps to connect power. The switchplate supplies power to the antenna. a. Before you begin, di sconnect ve ssel power. b. Connect a power cable to 12 VDC vessel power (for cable speci fic ations, see Figure 3 on page 3). c. Connect your vessel power wires to the power (+) and ground (-) input terminals on the switchplate (see Figure ...

  • KVH Industries TracVisionM7 - page 13

    13 In Step 3, you identified a suitable mounting location for the switchplate and cut out the mounting hole in the mounting surface. Now follow these steps to mount the switchplate. a. Fit the switchplate assembly into the mounting hole until it is flush with the mounting surface. b. Drill four 5/32" (4 mm) holes in the countersunk settings in ...

  • KVH Industries TracVisionM7 - page 14

    14 Follow these steps to enter your vessel’s latitude and longitude into the antenna. NOTE: The antenna will use your position information to speed up satellite acquisition. If the antenna knows where you are, it knows where it should start looking for the satellite (see Figure 22). In addition, for a linear syst em, the antenna will use your pos ...

  • KVH Industries TracVisionM7 - page 15

    15 c. Ensure the antenna has a clear, unobstructed view of the sky. d. Apply power to the satellite TV receiver(s) and the switchplate (see Figure 23 on page 14). Wait two minutes for sy stem startup. e. Data should now be scrolling in your HyperTerminal window (s ee Figure 25). If no data appears, check your connections and make sure you’re usin ...

  • KVH Industries TracVisionM7 - page 16

    16 Follow these steps to set up the system for the desired pair of satellites. Enter the following comma nds via Windows HyperTerminal or KVH Flash Update Wizard: a. Type HALT then press Enter. b. Type DEBUGON then press Enter. c. Type the following command the n press Enter. Italics indicate a variable. SATINSTALL, SatelliteA,SatelliteB SatelliteA ...

  • KVH Industries TracVisionM7 - page 17

    17 Follow these steps to set the ant enna’s linear LNB to the correct skew angle for your selecte d satellite and vessel position. a. Using HyperTerminal or KVH Flash Update Wizard, type SKEWANGLE then press Enter. Note the reported skew angle. TIP: The SKEWANGLE command provides the correct skew angle for the cu rrently selected satellite only. ...

  • KVH Industries TracVisionM7 - page 18

    18 The installation process is complete! Before you depart the vessel, test the system to verify the antenna works properly. Then give the Customer Welcome Kit to the customer and explain how to use the system. Also be sure the customer understands the followin g: • Keep the radome installed on the antenna at all times. The radome protects the an ...

  • KVH Industries TracVisionM7 - page 19

    Appendices 19 This section provides supplement al instructions for advanced configurations. It also provides system wiring diagrams and a switchplate mounting template. Contents A. Wiring 3+ Receivers, 21 B. Satellite Library, 23 C. User-Defined Satellites, 24 D. Wiring Diag rams, 27 Switchplate Mounting Template, 31 ...

  • KVH Industries TracVisionM7 - page 20

    21 Antenna with Circular Dual LNB (North American syste ms only) To connect three or more receivers, follow these steps to install an acti ve (powered) multiswitch between the antenna and the rece ivers. NOTE: You can purchase an active multiswitch, Channel Master model 6314IFD, from KVH (order part #19-0123). 1. Connect the RF1 cable from the ante ...

  • KVH Industries TracVisionM7 - page 21

    22 Antenna with Linear Quad LNB (European systems only) Follow these steps to connect three or four receivers directly to the antenna. NOTE: If you need to conn ect more than four receivers to the TracVision system, install an active multiswitch that generates a 22 KHz tone (such as Spaun model 5602NF - KVH part #19-0 413). Connect the multiswitch ...

  • KVH Industries TracVisionM7 - page 22

    23 The TracVision antenna can track a variety of DVB-compatible and DSS (DIRECTV) satellites. Most popular satellites are programmed in the antenna’s libra ry (see the tables below). Satellite Librar y B Appendix North America Standard Circular Dual LNB Required Asia Standard Circular Dual LNB Required Latin America Galaxy Circular Dual LNB Requi ...

  • KVH Industries TracVisionM7 - page 23

    24 The satellite library in the TracVision ante nna includes two slots for user-defined satellites (USER 1 and USER 2). You can program one or both of these library slots for any satellite you wish that is not already set up in the library. To configure a user-defined satellite, you will need to program into the antenna the following information ab ...

  • KVH Industries TracVisionM7 - page 24

    25 Enter the following comma nds via Windows HyperTerminal or KVH Flash Update Wizard. 1. Type HALT then press Enter. 2. Type DEBUGON then press Enter. 3. Type the following SATCONFIG command then press Ent er. Italics indicate a variable field (see Figure 33 for definitions). SATCONFIG,USER A,B,C, D,E 4. Type @DEBUGON then press Enter. 5. Type the ...

  • KVH Industries TracVisionM7 - page 25

    26 Example - Linear Satellite The following is an example of programming a linear user-defined satellite (USER 1). Satellite Name: YOURSAT 123 at 7°W Commands you would enter into the antenna via HyperTerminal or KVH Flash Update Wizard: HALT DEBUGON SATCONFIG,US ER1,7,W, 3,L @DEBUGON @SATCONFIG,A,98,11966, 275 00,34,0x0800,H,H,3 @SATCONFIG,A,98,1 ...

  • KVH Industries TracVisionM7 - page 26

    27 This appendix provides system wiring diagrams for the following receiver configurations: • One or two receivers • Three or more receivers (circular) • Three or more receivers (linear quad) The wiring diagrams on the following pages are intended as a q uick reference only. Be sure to follow the complete wiring instructions provided earlier ...

  • KVH Industries TracVisionM7 - page 27

    28 Wiring One or T wo Receivers Continued... D Data Switchplate Antenna Po w e r SATELLITE IN OUT TO TV TV ANT/CABLE IN AUDIO VIDEO S-VIDEO PHONE JA CK RL SA TELLITE IN Secondar y Receiv er - Optional Primar y Receiver SATELLITE IN OUT TO TV TV ANT/CABLE IN AUDIO VIDEO S-VIDEO PHONE JA CK RL SA TELLITE IN This receiv er controls satellite selection ...

  • KVH Industries TracVisionM7 - page 28

    29 Wiring Three or Four Receivers (Circular) Continued... D + – + – Switchplate +12 VDC RF2 RF1 LHCP +18V RHCP +13V Antenna Receiv er #2 SATELLITE IN OUT TO TV TV ANT/CABLE IN AUDIO VIDEO S-VIDEO PHONE JA CK RL SA TELLITE IN Receiv er #1 SATELLITE IN OUT TO TV TV ANT/CABLE IN AUDIO VIDEO S-VIDEO PHONE JA CK RL SA TELLITE IN Receiv er #3 SATELLI ...

  • KVH Industries TracVisionM7 - page 29

    30 Wiring Three or Four Re ceivers (Linear Quad) Continued... D Antenna Receiv er #2 SATELLITE IN OUT TO TV TV ANT/CABLE IN AUDIO VIDEO S-VIDEO PHONE JA CK RL SA TELLITE IN Receiv er #1 (Primar y) SATELLITE IN OUT TO TV TV ANT/CABLE IN AUDIO VIDEO S-VIDEO PHONE JA CK RL SA TELLITE IN Receiv er #3 SATELLITE IN OUT TO TV TV ANT/CABLE IN AUDIO VIDEO S ...

  • KVH Industries TracVisionM7 - page 30

    31 3.82" (97 mm) .32" (8 mm) 2.36" (60 mm) .16" (4 mm) 3.19" (81 mm) 2.05" (52 mm) P anel Cutout 3 / 32 " (2.25 mm) Switchplate Mounting T emplate ...

  • KVH Industries TracVisionM7 - page 31

    KVH Industries, Inc. 50 Enterprise Center Middletown, RI 02842-5279 U.S.A. Phone: +1 401 847-3327 Fax: +1 401 849-0045 E-mail: info@kvh.com Internet: www .kvh.com KVH Europe A/S Kokkedal Industripark 2B 2980 Kokkedal Denmark Phone: +45 45 160 180 Fax: +45 45 160 181 E-mail: info@kvh.dk Internet: www .kvh.com © Copyright 2006 KVH Industries Inc. KV ...

Fabbricante KVH Industries Categoria Security Camera

I documenti che otteniamo dal fabbricante del dispositivoKVH Industries TracVisionM7 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici KVH Industries
- manuali per l’uso TracVisionM7
- schede prodotto KVH Industries
- opuscoli
- o etichette energetiche KVH Industries TracVisionM7
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso KVH Industries TracVisionM7.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione KVH Industries TracVisionM7, manuali di manutenzione, brevi manuali o manuali utente KVH Industries TracVisionM7. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto KVH Industries TracVisionM7.

Manuali per l’uso simili

Manuale completo del dispositivo KVH Industries TracVisionM7, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare KVH Industries TracVisionM7 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti KVH Industries TracVisionM7.

Il manuale per l’uso completo KVH Industries, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale KVH Industries TracVisionM7 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice KVH Industries TracVisionM7, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per KVH Industries TracVisionM7 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo KVH Industries TracVisionM7 - che ci dovrebbe aiutare nei primi passi durante l'uso KVH Industries TracVisionM7
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del KVH Industries TracVisionM7
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio KVH Industries TracVisionM7 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su KVH Industries TracVisionM7?

Utilizza il modulo sottostante

Se non hai risolto il problema con KVH Industries TracVisionM7 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con KVH Industries TracVisionM7 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)