Italiano dropdown-ico

Manuale per l’uso Harbor Freight Tools 46813

37 pagine 1.65 mb
Scarica

Vai alla pagina of 37

Summary
  • Harbor Freight Tools 46813 - page 1

    10" T ABLE SA W Model 46813 ASSEMBL Y AND OPERA TING INFORMA TION 3491 Mission Oaks Blvd., Camarillo, CA 9301 1 Visit our W eb site at http://www .harborfreight.com Copyright 2002 by Harbor Freight T ools ® . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the expre ...

  • Harbor Freight Tools 46813 - page 2

    SPECIFICA TIONS T ABLE SA VE THIS MANUAL Y ou will need this manual for the safety warnings and precautions, assembly , operating, inspection, maintenance, and cleaning procedures, parts list and assembly diagrams. Keep your invoice with this manual. Write the invoice number on the inside of the front cover . Keep this manual and invoice in a safe ...

  • Harbor Freight Tools 46813 - page 3

    4. DO NOT USE THIS PRODUCT IF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not attempt to use this product. 5. USE EYE, HEARING, AND BREA THING PROTECTION. Wear ANSI approved safety impact eyeglasses, hearing protect ...

  • Harbor Freight Tools 46813 - page 4

    SPECIFIC PRODUCT W ARNINGS AND PRECAUTIONS 1. GROUND THIS PRODUCT . The electrical power cord for this product is equipped with a grounded 3-Prong Plug. Never remove the grounding prong or modify the Plug in any way . Do not use adapter plugs with this product. T o comply with the National Electric Code, and to provide additional protection from th ...

  • Harbor Freight Tools 46813 - page 5

    7. KEEP ALL GUARDS IN PLACE AND IN WORKING ORDER. 8. REMOVE ALL ADJUSTING WRENCHES FROM THE T ABLE SA W BEFORE TURNING IT ON. 9. A VOID UNINTENTIONAL ST ARTING. Make sure you are prepared to begin work before turning the Power Switch (part #8E) “ON”. 10. DO NOT USE THIS TOOL FOR CUTTING MET ALS OR BRITTLE MA TERIALS. Do not cut dangerous materi ...

  • Harbor Freight Tools 46813 - page 6

    20. (Continued) T o avoid kickback, keep a firm grip on the workpiece at all times. Support overhanging work pieces; as the work piece is cut and weakens it will sag, causing a pinched Saw Blade. Push the workpiece slower than normal when cutting through knots, pressure treated and green lumber . Do not attempt to force the workpiece back on the cu ...

  • Harbor Freight Tools 46813 - page 7

    UNP ACKING When unpacking, check to make sure all parts shown on the Parts Lists (pages 27 through 29) are included. If any parts are missing or broken, please call Harbor Freight T ools at the number shown on the cover of this manual as soon as possible. PRODUCT OVERVIEW 1. NOTE: Prior to operating the 10" T able Saw , make sure you familiari ...

  • Harbor Freight Tools 46813 - page 8

    FIGURE C SKU 46813 P AGE 8                ? ...

  • Harbor Freight Tools 46813 - page 9

    ASSEMBL Y INSTRUCTIONS NOTE: For additional references to the parts listed below , refer to the Assembly Diagrams on pages 29 through 37 of this manual. W ARNING! PRIOR T O PERFORMING ANY ASSEMBL Y PROCEDURES, MAKE SURE THE 10" T ABLE SA W IS DISCONNECTED FROM ITS ELECTRICAL POWER SOURCE. T o Mount The 10" T able Saw On A W orkbench: 1. N ...

  • Harbor Freight Tools 46813 - page 10

    3. Attach one Short Leg Brace (part #9B) to the lower mounting holes in two Legs (part #4B), using one Carriage Bolt (part #5B), one W asher (part #3B), and one Hex Nut (part #2B) for each Short Leg Brace. Repeat the assembly procedure for the remaining one Short Leg Brace and two Legs. (See Figure B, and Assy . Diagram B.) 4. Attach one Side Brace ...

  • Harbor Freight Tools 46813 - page 11

    END BRACE (#6B) MOUNTING HOLES END BRACE (#6B) HEX NUT (#2B) W ASHER (#3B) BASE (#1G) HEX HEAD BOL T (#8B) BASE (#1G) FIGURE D T o Assemble The Extension T ables: 1. With the 10" T able Saw upside down, align the right and left side Extension T ables (part #5H) with the right and left ends of the T able Saw (with the beveled edges in front). ( ...

  • Harbor Freight Tools 46813 - page 12

    EXTENSION T ABLE (#5H) HEX HUT (#13H) HEX HEAD BOL T (#1 1H) W ASHER (#12H) 10” T ABLE SA W EXTENSION T ABLE (#5H) HEX NUT (#13H) SQUARE HEAD BOL T (#10H) EXTENSION T ABLE (#5H) FIGURE E FIGURE F W ASHER (#12H) SKU 46813 P AGE 12 ...

  • Harbor Freight Tools 46813 - page 13

    3. NOTE: The back side of the Front Rail (part #7H) has two slots. Slide the upper slot of the Front Rail over the Square Head Bolts (part #10H). (See Figures F , G, and Assy . Diagram H.) 10” T ABLE SA W/EXTENSION T ABLES (#5H) HEX NUT (#13H) W ASHER (#12H) SEMI-CIRCLE HEAD SCREW (#2E) SWITCH PLA TE (#3E) SQUARE NUT(#4E) (LOWER SLOT) FRONT RAIL ...

  • Harbor Freight Tools 46813 - page 14

    BASE (#1G) (RIGHT EDGE) EXTENSION T ABLE (#5H) 456789 SCALE (#6H) 7-1/8” MARK, RIGHT SCALE 3. Loosely attach a W asher (part #12H) and Hex Nut (part #13H) to each Square Head Bolt (part #10H). (See Figures I, J, and Assy . Diagram H.) FIGURE H 10” T ABLE SA W REAR RAIL (#3H) BASE (#1G) EXTENSION T ABLE (#5H) 2 -1 /2 ” FIGURE I 4. NOTE: The ba ...

  • Harbor Freight Tools 46813 - page 15

    10” T ABLE SA W/EXTENSION T ABLES (#5H) (REAR EDGES) REAR RAIL (#3H) SLOT SQUARE HEAD BOL T (#10H) W ASHER (#12H) HEX NUT (#13H) FIGURE J 5. Wrench tighten all five Square Head Bolts (part #10H). (See Figures I, J, and Assy . Diagram H.) T o Attach The Rip Fence And Miter Gauge: 1. Hook the Lock Block (part #7C) under the Rear Rail (part #3H). Th ...

  • Harbor Freight Tools 46813 - page 16

    RIP FENCE (#10C) LOCK BLOCK (#7C) REAR RAIL (#3H) SA W T ABLE FIGURE K SCALE INDICA TOR (#20C) RIP FENCE (#10C) FRONT RAIL (#7H) FINE ADJUSTMENT KNOB (#30C) SA W T ABLE (#17H) RIP FENCE HANDLE (#37C) FIGURE L T o Attach The Power Switch: 1. Insert two Semi-Circle Head Screws (part #2E) from the rear of the Switch Plate (part #3E). Then, loosely scr ...

  • Harbor Freight Tools 46813 - page 17

    T o Assemble And Attach The Bevel And Height Handles T o The Base: 1. Insert one Screw (part #6G) each through a Bevel Handle and Height Handle (part #5G). T ighten each Screw into a Hand Wheel Assembly (part #4G). Then, attach an End Cap (part #7G) to each of the two Handles. (See Figures B, M, and Assy . Diagram G.) 2. Align one Handle Assembly ( ...

  • Harbor Freight Tools 46813 - page 18

    3. Secure the Motor Bracket (part #7F) to the Motor Mounting Plate (part #50-I), using four Hex Head Bolts (part #9-I), eight W ashers (part #52-I), four Lock W ashers (part #1-I), and four Hex Nuts (part #51-I). (See Figure N, and Assy . Diagrams F , and I.) LOCK W ASHER (#1-I) HEX NUT (#51-I) W ASHER (#52-I) HEX HEAD BOL T (#9-I) BEL T GUARD MOUN ...

  • Harbor Freight Tools 46813 - page 19

    2. Secure the Belt Guard (parts #1F , #4F) to the Motor (part #7F), using four Flat W ashers (part #3F) and four Hex Nuts (part #2F). (See Figures N, O, and Assy . Diagram F .) OUTER BEL T GUARD (#1F) MOTOR PULLEY (#5F) FLA T WASHER (#3F) HEX NUT (#2F) INNER BEL T GUARD (#4F) FIGURE O T o Attach The V-Belt: 1. T urn the Height Handle counterclockwi ...

  • Harbor Freight Tools 46813 - page 20

    3. Push the Motor (part #7F), with its attached Belt Guard (parts #1F , #4F), forward and place the V-Belt (part #40-I) on the Motor Pulley (part #5F). (See Figure P , and Assy . Diagrams F , and I.) 4. T urn the Height Handle clockwise until it stops. (See Figure B, and Assy . Diagram G.) 5. Pull the Motor (part #7F), with its attached Belt Guard ...

  • Harbor Freight Tools 46813 - page 21

    OUTER BLADE W ASHER (#15-I) ARBOR SHAFT (#13-I) BLADE NUT (#16-I) 10” SA W BLADE (#14-I) FIGURE R 3. Reach into the Saw Blade opening and remove the Blade Nut (part #16-I)) and Outer Blade W asher (part #15-I). (See Figure R, and Assy . Diagram I.) 4. Place the 10" Saw Blade (part #14-I) on the Arbor Shaft (part #13-I)). NOTE: Make sure the ...

  • Harbor Freight Tools 46813 - page 22

    6. Once the 10" Saw Blade (part #14-I) is secured onto the Arbor Shaft (part #13-I), replace the Throat Plate (part #15H) and tighten the Flat Head Screw (part #16H) back in place. (See Figure Q, and Assy . Diagram H.) T o Attach The Blade Guard Assembly: 1. Unscrew and temporarily remove the Flat Head Screw (part #16H)) located at the front o ...

  • Harbor Freight Tools 46813 - page 23

    OPERA TING INSTRUCTIONS T o Raise And Lower The 10" Saw Blade: 1. When cutting, the top edge of the Saw Blade (part #14-I) should rise about 1/4” above the top edge of the workpiece. 2. T o raise the height of the 10" Saw Blade (part #14-I), unlock the Bevel Lock (part #19-I). Next, turn the Height Handle (part #5G) clockwise until the ...

  • Harbor Freight Tools 46813 - page 24

    3. T o adjust the bevel of the 10" Saw Blade (part #14-I), unlock the Bevel Lock (part #19-I). Next, move the Bevel Handle (part #5G) to the right or left until the desired bevel of the 10" Saw Blade is shown by the Bevel Scale (part #10G). Then, re-lock the Bevel Lock. (See Figure B, and Assy . Diagrams G, and I.) T o Adjust The Angle Of ...

  • Harbor Freight Tools 46813 - page 25

    2. Before each use, inspect the general condition of the 10" T able Saw . Inspect the Power Switch (part #8E), Power Plug and Cord Assembly (part #8F), and extension cord (if used) for damage. Check for loose screws, misalignment, binding of moving parts, broken, cracked, or improper mounting of the 10" Saw Blade (part #14-I), broken part ...

  • Harbor Freight Tools 46813 - page 26

    '       ? ...

  • Harbor Freight Tools 46813 - page 27

     8 = $   8 = $   +        +      ...

  • Harbor Freight Tools 46813 - page 28

    P ARTS LIST SKU 46813 P AGE 28  8  = $   8 = $       ;        ; ? ...

  • Harbor Freight Tools 46813 - page 29

     8 = $   8 = $   0    0    0    0 ? ...

  • Harbor Freight Tools 46813 - page 30

    ASSEMBL Y DIAGRAM B NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts. SKU 46813 P AGE 30 ...

  • Harbor Freight Tools 46813 - page 31

    ASSEMBL Y DIAGRAM C NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts. SKU 46813 P AGE 31 ...

  • Harbor Freight Tools 46813 - page 32

    ASSEMBL Y DIAGRAM D NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts. SKU 46813 P AGE 32 ...

  • Harbor Freight Tools 46813 - page 33

    ASSEMBL Y DIAGRAM E NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts. SKU 46813 P AGE 33 ...

  • Harbor Freight Tools 46813 - page 34

    ASSEMBL Y DIAGRAM F NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts. SKU 46813 P AGE 34 ...

  • Harbor Freight Tools 46813 - page 35

    ASSEMBL Y DIAGRAM G NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts. SKU 46813 P AGE 35 ...

  • Harbor Freight Tools 46813 - page 36

    ASSEMBL Y DIAGRAM H NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts. SKU 46813 P AGE 36 ...

  • Harbor Freight Tools 46813 - page 37

    ASSEMBL Y DIAGRAM I NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts. SKU 46813 P AGE 37 ...

Fabbricante Harbor Freight Tools Categoria Saw

I documenti che otteniamo dal fabbricante del dispositivoHarbor Freight Tools 46813 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Harbor Freight Tools
- manuali per l’uso 46813
- schede prodotto Harbor Freight Tools
- opuscoli
- o etichette energetiche Harbor Freight Tools 46813
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Harbor Freight Tools 46813.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Harbor Freight Tools 46813, manuali di manutenzione, brevi manuali o manuali utente Harbor Freight Tools 46813. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Harbor Freight Tools 46813.

Manuali per l’uso simili

Manuale completo del dispositivo Harbor Freight Tools 46813, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Harbor Freight Tools 46813 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Harbor Freight Tools 46813.

Il manuale per l’uso completo Harbor Freight Tools, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Harbor Freight Tools 46813 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Harbor Freight Tools 46813, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Harbor Freight Tools 46813 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Harbor Freight Tools 46813 - che ci dovrebbe aiutare nei primi passi durante l'uso Harbor Freight Tools 46813
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Harbor Freight Tools 46813
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Harbor Freight Tools 46813 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Harbor Freight Tools 46813?

Utilizza il modulo sottostante

Se non hai risolto il problema con Harbor Freight Tools 46813 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Harbor Freight Tools 46813 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)