Italiano dropdown-ico

Manuale per l’uso Desa 496

28 pagine 1.01 mb
Scarica

Vai alla pagina of 28

Summary
  • Desa 496 - page 1

    Important: Read this manual and all labels carefully before operating your powder actuated tool. This manual should always accompany the tool and be transferred with it upon change of ownership. Operating Instructions POWDER ACTUATED TOOL MANUFACTURERS´ INSTITUTE INC. ™ G 029 ® A N I N D E P E N D E N T L A B O R A T O R Y T E S T I N G F O R P ...

  • Desa 496 - page 2

    2 105635 INDEX Warning: Safety Precautions ............................................................ 3-11 Why A Fastener Holds ........................................................................ 12 Selecting Fasteners and Power loads ................................................ 13 Operation .............................................. ...

  • Desa 496 - page 3

    3 105635 G 018 W arning: Safety Precautions IMPORTANT: Read these operating instructions carefully and com- pletely before trying to operate or service this tool. Improper use of this tool can cause serious injury or death from firing fastener into body or from flying debris. We expressly disclaim any liability for any injury to persons or damage t ...

  • Desa 496 - page 4

    4 105635 482-12 G 018 Safety Precautions POWDER ACTUATED TOOLS IN USE WARNING 482-10 ! 4. Always clear the work area on all sides and post appropriate warning signs on job sites. G 018 G 018 1. Never place your hand over the muzzle. Accidental discharge can cause serious injury. HANDLING THE TOOL 2. Never place your finger on the trigger until the ...

  • Desa 496 - page 5

    5 105635 G 018 G 018 G 018 G 018 Safety Precautions 4 . Never carry or pass a loaded powder actuated tool. Never point a powder actuated tool at anyone. 3. Store powder actuated tool and power load strips in a locked container. Unload tool before storing. Keep power loads of different power levels in separate containers. 5. If the tool is dropped, ...

  • Desa 496 - page 6

    6 105635 TOO HARD Point flattens 482-29 TOO BRITTLE Surface shatters 482-30 TOO SOFT Sinks in with average hammer blow 482-28 ? ? ? G 018 G 018 G 018 G 018 Safety Precautions 7. An operator taking medication should take extra precautions while handling the tool. Never drink alcoholic beverages or take medications which impair your vision, balance o ...

  • Desa 496 - page 7

    7 105635 TILE BRICK 482-33 CAST IRON GLASS G 018 G 018 G 018 G 018 G 018 Safety Precautions 3. Never make fastenings in spalled or cracked areas. 2 . Never attempt to drive power fasteners into very hard or brittle materials including, but not limited to cast iron, glass, tile, stone, brick, or hardened steel. Materials of this type tend to shatter ...

  • Desa 496 - page 8

    8 105635 TOO THIN WELD 482-40 G 018 3/16" MIN 1/2" 1" 482-41 Safety Precautions 7. Do not drive power fasteners into steel base material less then 3/16" thick, within 2" of a weld, within 1/2" of the edge or within 1" of another power fastener. 3" 3" 3" 482-39 6. Do not drive power fasteners into co ...

  • Desa 496 - page 9

    9 105635 POWER LOADS POWER LOADS GASOLINE GAS OLINE 482-50 482-49 G 018 G 018 G 018 G 018 G 018 Safety Precautions 2. Should the tool fail to fire, hold the muzzle firmly against the work surface for 30 seconds. Release the trigger and remove pressure on the tool while holding the muzzle against the work surface. Again press the tool firmly against ...

  • Desa 496 - page 10

    10 105635 YELLOW? GREEN? RED? POWDER LOADS ONLY 482-57 Safety Precautions 1 2 3 4 5 6 7 8 9 10 11 12 1 22 L E K C I N B R A S S 482-54 C A L I B E R NOTE: Failure to start with the lowest power level can result in overdrive condition and will result in damage to tool (See page 13). 2. Remington power load strips are available in three power levels ...

  • Desa 496 - page 11

    11 105635 482-59 G 018 Safety Precautions 6. Power fasteners are a permanently installed fixture. An act of demolition is required for their removal. Appropriate safety precautions must be taken. 9. If work is interrupted for any reason, remove the power load strip before removing the power fastener. 8. Never pry a power load out of the strip. Pryi ...

  • Desa 496 - page 12

    12 105635 Why A Power Fastener Holds WHY A POWER FASTENER HOLDS IN CONCRETE The compression bond of the concrete to the power fastener accounts for the majority of the holding power. The fastener displaces the concrete which tries to return to its original form causing a squeezing effect. Maximum holding power is achieved when the depth of penetrat ...

  • Desa 496 - page 13

    13 105635 482-67 OVERDRIVE G 018 Selecting Power Fasteners and Power loads FASTENING INTO CONCRETE The proper power fastener length can be determined by adding the thickness of the material to be fastened and the amount of fastener that will actually penetrate the con- crete. The concrete must be three times as thick as the intended fastener penetr ...

  • Desa 496 - page 14

    14 105635 Operation 1. Grasp barrel assembly and slide forward rapidly until it stops. Push barrel assembly back into tool to the closed position. This sets piston into firing position. 4. Place the muzzle of tool perpendicular to work surface without tilting the tool. Push tool against work surface until sliding action of barrel stops. 3. Select t ...

  • Desa 496 - page 15

    15 105635 Operation 5. Squeeze trigger to set power fastener. Be sure to keep pressure on tool during this operation. 7. Should the tool fail to fire, hold the muzzle firmly against the work surface for 30 seconds. Release the trigger and remove pressure on the tool while holding the muzzle against the work surface. Again press the tool firmly agai ...

  • Desa 496 - page 16

    16 105635 Parts List 496 Key Part No. No. Description Qty. 1 502001 Housing 1 2 502100 Outer Liner Assembly 1 3 501104 Push Pin 1 4 301013 Ball Setter 2 5 501106 Spring Ball Set 1 6 501107 Key Stop 1 7 301014 Annular Spring 1 8 502200 Barrel 1 9 502202 Piston Assembly (Includes Ring) 1 10 501212 Ring 1 11 502215 3" Muzzle Cap 1 12 TA4086 Plast ...

  • Desa 496 - page 17

    17 105635 Cleaning and Maintenance Clean tool after each days use. Disassemble and clean the barrel assembly with the wire brush provided with tool. Notice: Do not attempt to clean power load strip channel with wire brush. Apply good quality penetrating lubricant spray (such as WD-40) sparingly and wipe dry. 1 3 2 4 5 6 7 4 8 9 10 11 12 13 14 15 16 ...

  • Desa 496 - page 18

    18 105635 T ool Disassembly Figure 2 - Removing Stop Stop A. REMOVING BARREL ASSEMBLY 1. Using screwdriver, lift end of annular spring and rotate spring until stop is uncovered (see Figure 1). Annular Spring WARNING: Always unload a powder actuated tool before disassembling, replacing barrel, cleaning, or assembling. Stop 3. Pull barrel assembly ou ...

  • Desa 496 - page 19

    19 105635 6. Remove piston assembly from barrel (see Figure 4). B. REMOVING REAR PAD AND HANDLE PAD ASSEMBLY 1. Loosen screws on back of handle pad assembly and rear pad with 3mm Allen wrench. 2. Remove assembly handle pad and rear pad. Do not remove the screw from the assembly handle pad (see Figure 5). 3mm Allen Wrench Figure 5 - Removing Handle ...

  • Desa 496 - page 20

    20 105635 D. REMOVING FIRING PIN 1. Remove two springs from outer liner assembly (see Figure 8). 2. Push in sear and pull out firing pin guide (see Figure 8). Line up sear with end of slot. Remove spring and sear. Remove firing pin assembly. Remove push pin (see Figure 9). Figure 8 - Removing Springs and Pushing in Sear to Remove Firing Pin Guide F ...

  • Desa 496 - page 21

    21 105635 T ool Assembly WARNING: Always unload a powder actuated tool before disassembling, replacing barrel, cleaning, or assembling. A. INSERTING OUTER LINER ASSEMBLY INTO HOUSING 1. Place ball bearing and spring in end of outer liner assembly (see Figure 11, page 20). 2. Slide outer liner assembly into tool body. B. ATTACHING TRIGGER ASSEMBLY T ...

  • Desa 496 - page 22

    22 105635 F. ASSEMBLING BARREL ASSEMBLY 1. Insert piston assembly into barrel (see Figure 17). Piston Barrel Figure 17 - Inserting Piston in Barrel 2. Insert buffer in muzzle cap. 3. Screw muzzle cap to barrel assembly. 4. Insert barrel into outer liner assembly (see Figure 18). Muzzle Cap Buffer Barrel Piston Figure 18 - Inserting Barrel Assembly ...

  • Desa 496 - page 23

    23 105635 5. Insert stop into slot on outer liner assembly (see Figure 19). Stop Figure 19 - Replacing Stop Outer Liner Assembly 6. Push stop towards front of tool (see Figure 20). Stop Figure 20 - Pushing Stop towards Front of Tool Annular Spring Stop Figure 21 - Rotating Annular Spring to Secure Stop 7. Rotate annular spring until stop is covered ...

  • Desa 496 - page 24

    24 105635 T roubleshooting Guide Piston hangs out of muzzle. Overdriven fastener. Piston jammed. Power load strip will not advance. Reduction or loss of power. Tool does not completely depress. Tool does not fire. Opening and clos- ing of barrel or pushing down on tool, etc. is not smooth but is rough or binds. PROBLEM Tool overdriven. Piston not p ...

  • Desa 496 - page 25

    25 105635 Parts Centrals Contact authorized dealers of this product. If they can’t supply original replace- ment part(s), either contact your nearest Parts Central (see below) or call DESA International’s Parts Department at 1-800-972-7879for information. When calling DESA International, have ready • model number of your tool • replacement ...

  • Desa 496 - page 26

    26 105635 Application Chart 2 1/2" 2 1/2" 2" 1 1/2" 1 1/2" 1 1/2" 1" 1" 1" to this Concrete Cement Block Steel (3/16" to 3/8" Thick) Concrete Cement Block Steel (3/16" to 3/8" Thick) Concrete Cement Block Steel (3/16" to 3/8" Thick) Yellow Green Yellow/Red power load color p ...

  • Desa 496 - page 27

    27 105635 Maintenance Log Date Maintenance Performed ...

  • Desa 496 - page 28

    Limited W arranty Agreement DESA International warrants the Remington Power Pro  Model 496 against defects in materials and workmanship for a period of one (1) year from the date of purchase. If within one (1) year from the purchase date this Powder Actuated Tool fails due to a defect in material or workmanship, DESA will send replacement part(s ...

Fabbricante Desa Categoria Drill

I documenti che otteniamo dal fabbricante del dispositivoDesa 496 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Desa
- manuali per l’uso 496
- schede prodotto Desa
- opuscoli
- o etichette energetiche Desa 496
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Desa 496.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Desa 496, manuali di manutenzione, brevi manuali o manuali utente Desa 496. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Desa 496.

Manuali per l’uso simili

Manuale completo del dispositivo Desa 496, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Desa 496 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Desa 496.

Il manuale per l’uso completo Desa, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Desa 496 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Desa 496, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Desa 496 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Desa 496 - che ci dovrebbe aiutare nei primi passi durante l'uso Desa 496
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Desa 496
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Desa 496 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Desa 496?

Utilizza il modulo sottostante

Se non hai risolto il problema con Desa 496 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Desa 496 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)