Italiano dropdown-ico

Manuale per l’uso Peerless Industries ONE-TP

33 pagine 1.59 mb
Scarica

Vai alla pagina of 33

Summary
  • Peerless Industries ONE-TP - page 1

    Models: ONE-TP , ONE-TP-S, R TONE, R T ONES 3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com Features: • Fits 23" to 84" flat panel screens • Easily expandable adapter brackets and wall plate • Adjustable tilt of +15°/-5° for viewing flexibility ? ...

  • Peerless Industries ONE-TP - page 2

    2 of 33 ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 Note: Read entire instruction sheet before you start installation and assembly . T ools Needed for Assembly • stud finder ("edge to edge" stud finder is recommended) • phillips screwdriver • drill • 1/4" bit for concrete and cinder block wall • 5/32" bit for wood st ...

  • Peerless Industries ONE-TP - page 3

    3 of 33 ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 Parts may appear slightly different than illustrated. HH Parts List Black Silver Description Qt y . Part # Part# AA wall plate 1 201-1210 201-4210 BB left tilt bracket 1 201-0181 201-0192 CC right tilt bracket 1 201-0177 201-0193 DD #14 x 2.5 wood screw 6 5S1-015-C03 5S1-015-C03 EE Alligator® a ...

  • Peerless Industries ONE-TP - page 4

    4 of 33 ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 Loosen four 1/4-20 x 1/4" screws on each adapter bracket ( BB,CC ). Position extension brackets, with slots facing downward , onto adapter brackets ( BB,CC ) at the appropriate position to accommodate your screen as shown in Figure 1.1. Securely tighten all 1/4-20 x 1/4" screws as show ...

  • Peerless Industries ONE-TP - page 5

    5 of 33 ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 Att aching Tilt Bracket s to Screen using Baffled Fastener Pack NOTE: Refer to page 4 for adjustments of top extension bracket. T o prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Place screen face side down. Refer to screen manufac ...

  • Peerless Industries ONE-TP - page 6

    6 of 33 ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 Begin with the shortest length screw , hand thread through multi-washer and adapter bracket into screen as shown below . Screw must make at least three full turns into the mounting hole and fit snug into place. Do not over tighten. If screw cannot make three full turns into the screen, select a ...

  • Peerless Industries ONE-TP - page 7

    7 of 33 ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 With tape measure, measure the outside to outside of the brackets on the back of your screen. If width of the tilt brackets on back of the screen is over 18-1/2" shown in figure 3.1, using a 7/16" wrench, attach wing bracket ( GG ) to center bracket using two 1/4" serrated flanged ...

  • Peerless Industries ONE-TP - page 8

    8 of 33 ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 Inst allation to Double W ood Stud W all NOTE: If mounting equipment weighing greater than 200 lbs, triple stud mounting is strongly recommended. Skip to page 9 Wall plate ( AA ) can be mounted to two studs that are 16" apart. Use a stud finder to locate the edges of the studs. Use of an ed ...

  • Peerless Industries ONE-TP - page 9

    9 of 33 ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 Inst allation to T riple Wood S tud Wall fig. 4.3 CS = center of screen 4" (102 mm) 4" (102 mm) Wall plate ( AA ) can be mounted to three studs that are 16" apart. Use a stud finder to locate the edges of the studs. Use of an edge-to-edge stud finder is highly recommended. Based o ...

  • Peerless Industries ONE-TP - page 10

    10 of 33 ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 Inst allation to Solid Concrete or Cinder Block Make sure that wall plate ( AA ) is level, use it as a template to mark four mounting holes. The top mounting hole should be 2.5" above the desired screen center as shown in figure 4.1 on page 8. Drill four 1/4" (6 mm) dia. holes to a mi ...

  • Peerless Industries ONE-TP - page 11

    11 of 33 ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 Mounting and Removing Flat Panel Screen Adjust tension knobs shown in detail 2 to desired tension, balancing your screen size and weight. The tension knob, without changing the bracket tension, can be pulled out, away from the bracket and turned independently of the knob post for readjustment a ...

  • Peerless Industries ONE-TP - page 12

    Modelos: ONE-TP , ONE-TP-S, RT ONE, RT ONES 3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com Máxima capacidad de carga UL 250lb (1 13.5kg) Instalación y Ensamblaje: OneMount™ Este producto está inscripto en la Lista UL. Debe ser instalado por un instalador pro ...

  • Peerless Industries ONE-TP - page 13

    Visite el sitio Web de Peerless en www .peerlessmounts.com Para el Servicio al cliente llame al 1-800-729-0307 ó 708-865-8870 13 of 33 Español ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 T abla de contenido Lista de piezas ........................................................................................................................... ...

  • Peerless Industries ONE-TP - page 14

    Visite el sitio Web de Peerless en www .peerlessmounts.com Para el Servicio al cliente llame al 1-800-729-0307 ó 708-865-8870 14 of 33 Español ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 List a de las p artes Negro Plateado Descripción Cantidad # d e parte # de parte AA placa de pared 1 201-1210 201-4210 BB soporte de inclinación izquierdo 1 ...

  • Peerless Industries ONE-TP - page 15

    Visite el sitio Web de Peerless en www .peerlessmounts.com Para el Servicio al cliente llame al 1-800-729-0307 ó 708-865-8870 15 of 33 Español ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 Afloje cuatro tornillos de 1/4-20 x 1/4" en cada soporte de adaptación ( BB,CC ). Coloque los soportes de extensión, con las ranuras hacia abajo , contr ...

  • Peerless Industries ONE-TP - page 16

    Visite el sitio Web de Peerless en www .peerlessmounts.com Para el Servicio al cliente llame al 1-800-729-0307 ó 708-865-8870 16 of 33 Español ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 Fijación de los soportes inclinables a la p ant alla usando los sujet adores identificados y clasificados en las divisiones del emp aque plástico NOT A: Refi ...

  • Peerless Industries ONE-TP - page 17

    Visite el sitio Web de Peerless en www .peerlessmounts.com Para el Servicio al cliente llame al 1-800-729-0307 ó 708-865-8870 17 of 33 Español ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 Comience con uno de los tornillos más cortos, enrósquelo, con la mano, a través de la arandela múltiple y el soporte adaptador a la p arte posterior de la ...

  • Peerless Industries ONE-TP - page 18

    Visite el sitio Web de Peerless en www .peerlessmounts.com Para el Servicio al cliente llame al 1-800-729-0307 ó 708-865-8870 18 of 33 Español ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 Con la cinta de medir , mida del exterior al exterior de los soportes en la p arte de atrás de la pantalla. Si el ancho de los soportes de inclinación en la ...

  • Peerless Industries ONE-TP - page 19

    Visite el sitio Web de Peerless en www .peerlessmounts.com Para el Servicio al cliente llame al 1-800-729-0307 ó 708-865-8870 19 of 33 Español ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 Inst alación a dos mont antes en p ared de madera NOTA: Para montar equipo que pese más de 200 lbs, se recomienda enfáticamente el uso de tres montantes. Pa ...

  • Peerless Industries ONE-TP - page 20

    Visite el sitio Web de Peerless en www .peerlessmounts.com Para el Servicio al cliente llame al 1-800-729-0307 ó 708-865-8870 20 of 33 Español ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 Inst alación a tres mont antes en p ared de madera fig. 4.3 4" (102 mm) 4" (102 mm) La placa de pared ( AA ) se puede fijar a tres montantes que ten ...

  • Peerless Industries ONE-TP - page 21

    Visite el sitio Web de Peerless en www .peerlessmounts.com Para el Servicio al cliente llame al 1-800-729-0307 ó 708-865-8870 21 of 33 Español ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 T aladre hoyos e inserte las expansiones ( EE ). Coloque la placa ( AA ) sobre las expansiones ( EE ) y fíjela con los tornillos ( DD ). Apriete todos los fij ...

  • Peerless Industries ONE-TP - page 22

    Visite el sitio Web de Peerless en www .peerlessmounts.com Para el Servicio al cliente llame al 1-800-729-0307 ó 708-865-8870 22 of 33 Español ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 CS Cómo mont ar y remover la pant alla de p anel plano Ajuste los botones de tensión que se muestran en el detalle 2 a la tensión deseada, para balancear el ...

  • Peerless Industries ONE-TP - page 23

    Modèles: ONE-TP , ONE-TP-S, R TONE, R TONES Caractéristiques : • Convient aux écrans plats de 23 à 84 po • Supports adaptateurs et plaque murale facilement extensibles • Inclinaison réglable sur +15°/-5° offrant divers angles de visionnement • Conception intuitive facilitant l’installation • Quincaillerie de sécurité pour aider ...

  • Peerless Industries ONE-TP - page 24

    Adresse de notre site internet : www .peerlessmounts.com Service clientèle : 1-800-729-0307 ou 708-865-8870 Français 24 of 33 ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 Remarque : V euillez lire la feuille d’instructions au complet avant de commencer l’installation et le mont age. Outils nécessaires au mont age • localisateur de montant ...

  • Peerless Industries ONE-TP - page 25

    Adresse de notre site internet : www .peerlessmounts.com Service clientèle : 1-800-729-0307 ou 708-865-8870 Français 25 of 33 ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 Liste des pièces Noir Argent Description Q t é Pièce n o Pièce n o AA plaque murale 1 201-1210 201-4210 BB support inclinable gauche 1 201-0181 201-0192 CC support inclinab ...

  • Peerless Industries ONE-TP - page 26

    Adresse de notre site internet : www .peerlessmounts.com Service clientèle : 1-800-729-0307 ou 708-865-8870 Français 26 of 33 ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 Desserrez quatre vis de 1/4-20 x ¼ po sur chaque support adaptateur ( BB,CC ). Placez les rallonges de support de fixation, fentes vers le bas , sur les supports adaptateurs ( ...

  • Peerless Industries ONE-TP - page 27

    Adresse de notre site internet : www .peerlessmounts.com Service clientèle : 1-800-729-0307 ou 708-865-8870 Français 27 of 33 ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 Fixation des support s inclinables à l’écran à l’aide du jeu de fixations à comp artiment s REMARQUE : V euillez vous reporter à la page 26 pour le réglage de la rall ...

  • Peerless Industries ONE-TP - page 28

    Adresse de notre site internet : www .peerlessmounts.com Service clientèle : 1-800-729-0307 ou 708-865-8870 Français 28 of 33 ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 Commencez par la vis la plus courte et vissez-la manuellement à l’écran en la faisant passer à travers la rondelle tout usage et le support adaptateur , comme indiqué ci- ...

  • Peerless Industries ONE-TP - page 29

    Adresse de notre site internet : www .peerlessmounts.com Service clientèle : 1-800-729-0307 ou 708-865-8870 Français 29 of 33 ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 À l’aide d’un ruban à mesurer , mesurez les supports situés à l’arrière de l’écran d’un bord à l’autre. Si la largeur des supports inclinables situés à l? ...

  • Peerless Industries ONE-TP - page 30

    Adresse de notre site internet : www .peerlessmounts.com Service clientèle : 1-800-729-0307 ou 708-865-8870 Français 30 of 33 ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 Inst allation sur un mur à doubles mont ants en bois REMARQUE : Si le matériel de montage pèse plus de 200 lb (91 kg), il est fortement conseillé d’avoir recours au monta ...

  • Peerless Industries ONE-TP - page 31

    Adresse de notre site internet : www .peerlessmounts.com Service clientèle : 1-800-729-0307 ou 708-865-8870 Français 31 of 33 ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 Inst allation sur un mur à triples mont ant s en bois fig. 4.3 4" (102 mm) 4" (102 mm) La plaque murale ( AA ) peut être installée sur trois montants espacés de 1 ...

  • Peerless Industries ONE-TP - page 32

    Adresse de notre site internet : www .peerlessmounts.com Service clientèle : 1-800-729-0307 ou 708-865-8870 Français 32 of 33 ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 Inst allation sur du béton plein ou du bloc de béton DD AA EE Assurez-vous que la plaque murale ( AA ) est de niveau et utilisez-la comme gabarit pour marquer l’emplacement ...

  • Peerless Industries ONE-TP - page 33

    Adresse de notre site internet : www .peerlessmounts.com Service clientèle : 1-800-729-0307 ou 708-865-8870 Français 33 of 33 ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 • N’employez pas une force excessive pour serrer les vis. Un serrage excessif peut endommager le support. Serrez les vis à un couple maximum de 4,5 Nm (40 po-lb). • Pren ...

Fabbricante Peerless Industries Categoria Indoor Furnishings

I documenti che otteniamo dal fabbricante del dispositivoPeerless Industries ONE-TP possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Peerless Industries
- manuali per l’uso ONE-TP
- schede prodotto Peerless Industries
- opuscoli
- o etichette energetiche Peerless Industries ONE-TP
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Peerless Industries ONE-TP.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Peerless Industries ONE-TP, manuali di manutenzione, brevi manuali o manuali utente Peerless Industries ONE-TP. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Peerless Industries ONE-TP.

Manuali per l’uso simili

Manuale completo del dispositivo Peerless Industries ONE-TP, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Peerless Industries ONE-TP dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Peerless Industries ONE-TP.

Il manuale per l’uso completo Peerless Industries, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Peerless Industries ONE-TP - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Peerless Industries ONE-TP, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Peerless Industries ONE-TP che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Peerless Industries ONE-TP - che ci dovrebbe aiutare nei primi passi durante l'uso Peerless Industries ONE-TP
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Peerless Industries ONE-TP
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Peerless Industries ONE-TP in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Peerless Industries ONE-TP?

Utilizza il modulo sottostante

Se non hai risolto il problema con Peerless Industries ONE-TP con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Peerless Industries ONE-TP è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)